The Lulzbot TAZ6 single extruder configuration had an XY position for
z homing that did not match the factory firmware, and was off center
enough to cause the extruder to crash into the home button trim
sometimes when homing. This commit changes the printer config so
that the XY position for Z homing matches the original Marlin firmware
for this printer.
The Lulzbot TAZ6 single extruder configuration had an bed_tilt points
that did not match the factory firmware, and were off enough that the
nozzle (used for probing on this printer) could slip off the edge of
the probe point or miss it entirely. This commit changes the printer
config so that the coordinates for bed_tilt calibration match the
original Marlin firmware for this printer.
For the Lulzbot TAZ6 single extruder config, use 'gear_ratio' and
'rotation_distance' to configure the extruder.
The rotation distance is based on effective circumference of the hobbed
bolt based on the original Marlin firmware for the TAZ6 single-extruder,
and the gear ratio was determined by simply counting the number of
teeth on the pinion and spur gears.
Signed-off-by: Steven T. Snyder <github@steventsnyder.com>
Add support for automatically calculating the internal step_distance
from new config parameters - rotation_distance, microsteps,
full_steps_per_rotation, and gear_ratio.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Minor indentation changes and remove default values for heater_fan.
Add to printers.test test cases.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds config for the Monoprice Select Mini v2 cartesian printer. I have
successfully tested the configuration.
Signed-off-by: Kilian Neuner <github@9-r.net>
Add an 'mcu' option to the board_pins config and use that to specify
the name of the mcu to apply the aliases to. Support applying the
aliases to multiple mcus.
Add support for any number of options starting with an "aliases_"
prefix.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move all the config reference information from files in the config/
directory to a new Config_Reference.md document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Config should not specify a default pressure_advance. Note limit on
current with old 30 Ohm Z-motor.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fixing alias for thermistors to be on the host rather than the PRU.
Moving the D1W alias from PRU MCU to host MCU.
Signed-off by Jon Charnas <goeland86@gmail.com>
Corrected the diag1_pin numbers. Useful for anyone copying and pasting the lines. Its something really easy to look over and can lead to some hair pulling from the time wasted trying to troubleshoot why the tmc diag pin error from Klipper.
Signed-off-by: Juan Moreno <uncholowapo@gmail.com>
Adding board_pins section.
Added linux host MCU board pin aliases for endstops.
Also added a sample filament switch sensor config.
Signed-off-by: Jon Charnas <goeland86@gmail.com>
From July 2020, Ender 3 Pros came with a 32-bit Creality 4.2.2 board, similar to the Ender 3 V2. Unlike the Ender 3 V2, it comes with the ST7920 LCD screen and HR4988 steppers. Using the config file already in Marlin source, I came up with this klipper config file.
Signed-off-by: Matthias Liffers <m@tthi.as>
The following parameters have been tweaked:
- X endstop position has been set to -2, as per original marlin cofig
- Second Z axis disabled by default (this must be purchased as an
add-on)
The comment at the top of this file has also been modified to describe
the difference between this (old) model and the new (rebranded) Tevo
Tarantula pro.
Signed-off-by: Oliver Fawcett-Griffiths <olly@ollyfg.com>
By homing the y axis before the x axis, the nozzle will not touch the
plastic cover of the bed heater cable.
Signed-off-by: Yannic Schroeder <schroeder@ibr.cs.tu-bs.de>
menu.cfg:
- jinja2 template scripting
- new Setup menu
- new Calibration menu
menu:
- redesigned menu code
- jinja2 support
- option to reverse menu up and down directions
- functionality set to support menu injection from other modules
- a new way of defining menu hierarchy
- other adjustments
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
Using the setup_start_value() method avoids the PWM output line
transitioning to an intermediate state prior to setting the initial
value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add user-configurable contrast, vcomh (affects "smearing"), and invert options for SSD1306/SH1106 type OLED displays.
Signed-off-by: James Esau <james_esau@hotmail.com>
Input shaping can help to reduce printer vibrations due to resonances
and eliminate or reduce ghosting in prints.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
This commit allows to modify the icons (or glyphs) in the displays that
support it. Existing icons can be modified and new icons can be added via
a [display_glyph] section in the config.
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Option for using the current diameter instead of nominal while the first measurement isn't in place
Signed-off-by: Matthias Pabel <matthias.pabel@hs-augsburg.de>
Add config file to printers.test. Fix errors in config and unify
settings with the mini-e3-v1.2 config.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This is a basic config example for a SKR Mini E3 v2.0, the pinouts are different than the 1.2 and requires different compile options, so worth having an example.
Signed-off-by: Paul Greidanus <paul@majestik.org>
This gives it parity with heater_fan. Also change the default speed from
max_power to 1.0, since it is already scaled by max_power in set_speed.
Signed-off-by: Adrian Keet <arkeet@gmail.com>
Always disable the PWM after each command sent. Automatically trim
the command duration so the PWM disable doesn't increase the total
pulse time (when the duration is 200ms or greater).
Track the ideal command end time separately from the pwm transmit time
and only delay toolhead moves to this ideal time.
Update verify_state() to automatically schedule the check using the
time of the last sent command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's no longer necessary to queue gcode scripts - gcode.run_script()
now does that automatically.
Also, make release_gcode config optional.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the normal gcode.get_float() mechanism for extracting parameters
from the g-code command.
Don't register descriptions for the G2/G3 commands as the convention
is to only use descriptions for "extended g-code commands".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds config for the Ultimaker 2's UltiMainboard v2 board, with the
correct pins assigned and current control for the A4988 motor
drivers.
Signed-off-by: Avery Todd <averyct@pm.me>
The pin_up_touch_mode_reports_triggered should be set to True on all
genuine BLTouch.
Expand the description for stow_on_each_sample and state the default.
Reword the set_output_mode option to be more similar to other
descriptions.
It is no longer necessary to warn about clones being not supported.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fysetc Cheetah v1.2 boards require a special sequence to reset reliably.
This sequence works for me in all cases. Simpler sequences without
double reset did not work correctly. This is likely because of a weird
stateful circuitry for toggling the bootloader state.
Cheetah boards use RTS to configure bootloader triggering. By default,
pySerial sets RTS on connect, which unfortunately configures the board
to start the bootloader on reset.
Add a toggle for the RTS state to allow users to workaround. The RTS state
is set before the serial connection is opened, so there are no glitches.
Addresses #2026.
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
This config was not yet available - I have updated all the pin defines, starting with the BTT SKR board which is the most similar board + tested it on my printer which is currently working with the TMC5160 drivers using software SPI. I have not tested it with other drivers etc but the config should work for them.
Signed-off-by: Chester Lowrey <hilo90mhz@gmail.com>
Disable support for customizing the main lcd display content via the
menu system. Advise users to use the new display_data config sections
as a replacement.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a new config based system for specifying the on-screen
contents of an lcd screen. The default screen configuration (found in
klippy/extras/display/display.cfg) is the same as the previous
hard-coded display, so this should not change behavior for existing
users.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Correct TMC2130 diag1_pin logic - the diag1_pin logic should be inverted and pulled up.
Use pullup for endstops - pullups should be used here.
Signed-off-by: Wen-Jeng Hsiao <isuperwilly@gmail.com>
Update printer-seemecnc-rostock-max-v2-2015.cfg to include the [display] and [board_pins] sections needed for Reprap 20x4 LCD display (#2561).
Signed-off-by: Angelo Lagis <angelo_lagis@hotmail.com>
Support probing the corner washers for the bed tilt using G29,
flesh out the rest of the configuration for the display, and add
support for the Aerostruder (commented out by default).
Signed-Off-By: Chris Lee <clee@mg8.org>
Also applies to the Monoprice Maker Pro MK1.
This config is based on the version from Chris Barnes (https://www.facebook.com/Jarannis)
found on https://pastebin.com/raw/wm8PQezy. This config was mostly working and I
only had to change a few things:
- updated key names for min_point and max_point to mesh_min and mesh_max
- enabled PID control
- tweaked bounds to allow movement during mesh leveling
- removed all comments
- decreased homing speed slightly
- sane bed mesh sample defaults
In response to Kevin O'Connor:
- remove pressure_advance setting from extruder section
- remove respond section
- remove pause_resume section
Signed-off-by: Matt Shirley <mdshw5@gmail.com>
Steven Snyder
Timothée Girard
Kevin O'Connor
Sean McGroty
Pranas Kiziela
Justin Schuh
9R
Raabi91
Jeff Tang
Dushyant Ahuja
Dmitry Butyugin
Jon C
uncholowapo
Florian Heilmann
rjpatawaran
Vladimir Serov
Matthias Liffers
Oliver Fawcett-Griffiths
Yannic Schröder
Bryan Boettcher
Janar Sööt
Trevor Jones
bondus
Tonny Møller
Jimmacle
Voron
combolek
Iakabos
Paul Greidanus
James
Kianusch Sayah Karadji
Denis Ignatenko
Lucio Tarantino
matpab
Adrian Keet
Hywelmartin
camatthew88
Avery Todd
Grigori Goronzy
Chester
Arksine
Willy Hsiao
kakou-fr
Angelol125
FanDjango
Chris Lee
Matt Shirley
FanDjango
Junliang Yan
mtw3d