mirror of https://github.com/Desuuuu/klipper.git
config: Additional formatting changes to example-extras.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
3a15219de3
commit
11bf83b498
|
@ -181,15 +181,15 @@
|
|||
# to a probe_height position. The default is 5.
|
||||
|
||||
# Tool to help adjust bed screws tilt using Z probe. One may define a
|
||||
# [screws_tilt_adjust] config section to enable a SCREWS_TILT_CALCULATE
|
||||
# g-code command.
|
||||
# [screws_tilt_adjust] config section to enable a
|
||||
# SCREWS_TILT_CALCULATE g-code command.
|
||||
#[screws_tilt_adjust]
|
||||
#screw1: 100,100
|
||||
# The X,Y coordinate of the first bed leveling screw. This is a
|
||||
# position to command the nozzle to that is directly above the bed
|
||||
# screw (or as close as possible while still being above the bed).
|
||||
# This is the base screw used in calculations.
|
||||
# This parameter must be provided.
|
||||
# This is the base screw used in calculations. This parameter must
|
||||
# be provided.
|
||||
#screw1_name: front screw
|
||||
# An arbitrary name for the given screw. This name is displayed when
|
||||
# the helper script runs. The default is to use a name based upon
|
||||
|
@ -239,7 +239,8 @@
|
|||
# The height (in mm) that the head should be commanded to move to
|
||||
# just prior to starting a probe operation. The default is 5.
|
||||
#retries: 0
|
||||
# Number of times to retry if the probed points aren't within tolerance
|
||||
# Number of times to retry if the probed points aren't within
|
||||
# tolerance.
|
||||
#retry_tolerance: 0
|
||||
# If retries are enabled then retry if largest and smallest probed
|
||||
# points differ more than retry_tolerance. Note the smallest unit of
|
||||
|
@ -253,8 +254,8 @@
|
|||
# which is more flexible.
|
||||
# WARNING: Using this on a moving bed may lead to undesirable results.
|
||||
# If this section is present then a QUAD_GANTRY_LEVEL extended G-Code
|
||||
# command becomes available. This routine assumes the following Z motor
|
||||
# configuration:
|
||||
# command becomes available. This routine assumes the following Z
|
||||
# motor configuration:
|
||||
# ----------------
|
||||
# |Z1 Z2|
|
||||
# | --------- |
|
||||
|
@ -311,8 +312,8 @@
|
|||
# A X,Y coordinate (e.g. 100,100) where the Z homing should be
|
||||
# performed. This parameter must be provided.
|
||||
#speed: 50.0
|
||||
# Speed at which the toolhead is moved to the safe Z home coordinate.
|
||||
# The default is 50 mm/s
|
||||
# Speed at which the toolhead is moved to the safe Z home
|
||||
# coordinate. The default is 50 mm/s
|
||||
#z_hop:
|
||||
# Lift the Z axis prior to homing. This is applied to any homing
|
||||
# command, even if it doesn't home the Z axis. If the Z axis is
|
||||
|
@ -479,7 +480,8 @@
|
|||
# Set to true to enable FORCE_MOVE and SET_KINEMATIC_POSITION
|
||||
# extended G-Code commands. The default is false.
|
||||
|
||||
# Pause/Resume functionality with support of position capture and restore
|
||||
# Pause/Resume functionality with support of position capture and
|
||||
# restore.
|
||||
#[pause_resume]
|
||||
#recover_velocity: 50.
|
||||
# When capture/restore is enabled, the speed at which to return to
|
||||
|
@ -515,8 +517,8 @@
|
|||
# Enable the "M118" and "RESPOND" extended commands.
|
||||
#[respond]
|
||||
#default_type: echo
|
||||
# Sets the default prefix of the "M118" and "RESPOND" output to one of
|
||||
# the following:
|
||||
# Sets the default prefix of the "M118" and "RESPOND" output to one
|
||||
# of the following:
|
||||
# echo: "echo: " (This is the default)
|
||||
# command: "// "
|
||||
# error: "!! "
|
||||
|
@ -1693,8 +1695,8 @@
|
|||
# The amount of current (in amps RMS) used by the driver during
|
||||
# stepper movement. This parameter must be provided.
|
||||
#sense_resistor:
|
||||
# The resistance (in ohms) of the motor sense resistor. This parameter
|
||||
# must be provided.
|
||||
# The resistance (in ohms) of the motor sense resistor. This
|
||||
# parameter must be provided.
|
||||
#idle_current_percent: 100
|
||||
# The percentage of the run_current the stepper driver will be
|
||||
# lowered to when the idle timeout expires (you need to set up the
|
||||
|
@ -1726,10 +1728,10 @@
|
|||
# chip. This may be used to set custom driver parameters. The
|
||||
# defaults for each parameter are next to the parameter name in the
|
||||
# list above. See the TMC2660 datasheet about what each parameter
|
||||
# does and what the restrictions on parameter combinations are.
|
||||
# Be especially aware of the CHOPCONF register, where setting CHM to
|
||||
# either 0 or one will lead to layout changes (the first bit of HDEC)
|
||||
# is interpreted as the MSB of HSTRT in this case).
|
||||
# does and what the restrictions on parameter combinations are. Be
|
||||
# especially aware of the CHOPCONF register, where setting CHM to
|
||||
# either zero or one will lead to layout changes (the first bit of
|
||||
# HDEC) is interpreted as the MSB of HSTRT in this case).
|
||||
|
||||
# Configure a TMC5160 stepper motor driver via SPI bus. To use this
|
||||
# feature, define a config section with a "tmc5160" prefix followed by
|
||||
|
|
Loading…
Reference in New Issue