From 11bf83b49877f9db3f90072be73a3e078003c6a2 Mon Sep 17 00:00:00 2001 From: Kevin O'Connor Date: Fri, 16 Oct 2020 22:12:58 -0400 Subject: [PATCH] config: Additional formatting changes to example-extras.cfg Signed-off-by: Kevin O'Connor --- config/example-extras.cfg | 38 ++++++++++++++++++++------------------ 1 file changed, 20 insertions(+), 18 deletions(-) diff --git a/config/example-extras.cfg b/config/example-extras.cfg index 73e5cc19..b18c3c34 100644 --- a/config/example-extras.cfg +++ b/config/example-extras.cfg @@ -181,15 +181,15 @@ # to a probe_height position. The default is 5. # Tool to help adjust bed screws tilt using Z probe. One may define a -# [screws_tilt_adjust] config section to enable a SCREWS_TILT_CALCULATE -# g-code command. +# [screws_tilt_adjust] config section to enable a +# SCREWS_TILT_CALCULATE g-code command. #[screws_tilt_adjust] #screw1: 100,100 # The X,Y coordinate of the first bed leveling screw. This is a # position to command the nozzle to that is directly above the bed # screw (or as close as possible while still being above the bed). -# This is the base screw used in calculations. -# This parameter must be provided. +# This is the base screw used in calculations. This parameter must +# be provided. #screw1_name: front screw # An arbitrary name for the given screw. This name is displayed when # the helper script runs. The default is to use a name based upon @@ -239,7 +239,8 @@ # The height (in mm) that the head should be commanded to move to # just prior to starting a probe operation. The default is 5. #retries: 0 -# Number of times to retry if the probed points aren't within tolerance +# Number of times to retry if the probed points aren't within +# tolerance. #retry_tolerance: 0 # If retries are enabled then retry if largest and smallest probed # points differ more than retry_tolerance. Note the smallest unit of @@ -253,8 +254,8 @@ # which is more flexible. # WARNING: Using this on a moving bed may lead to undesirable results. # If this section is present then a QUAD_GANTRY_LEVEL extended G-Code -# command becomes available. This routine assumes the following Z motor -# configuration: +# command becomes available. This routine assumes the following Z +# motor configuration: # ---------------- # |Z1 Z2| # | --------- | @@ -311,8 +312,8 @@ # A X,Y coordinate (e.g. 100,100) where the Z homing should be # performed. This parameter must be provided. #speed: 50.0 -# Speed at which the toolhead is moved to the safe Z home coordinate. -# The default is 50 mm/s +# Speed at which the toolhead is moved to the safe Z home +# coordinate. The default is 50 mm/s #z_hop: # Lift the Z axis prior to homing. This is applied to any homing # command, even if it doesn't home the Z axis. If the Z axis is @@ -479,7 +480,8 @@ # Set to true to enable FORCE_MOVE and SET_KINEMATIC_POSITION # extended G-Code commands. The default is false. -# Pause/Resume functionality with support of position capture and restore +# Pause/Resume functionality with support of position capture and +# restore. #[pause_resume] #recover_velocity: 50. # When capture/restore is enabled, the speed at which to return to @@ -515,8 +517,8 @@ # Enable the "M118" and "RESPOND" extended commands. #[respond] #default_type: echo -# Sets the default prefix of the "M118" and "RESPOND" output to one of -# the following: +# Sets the default prefix of the "M118" and "RESPOND" output to one +# of the following: # echo: "echo: " (This is the default) # command: "// " # error: "!! " @@ -1693,8 +1695,8 @@ # The amount of current (in amps RMS) used by the driver during # stepper movement. This parameter must be provided. #sense_resistor: -# The resistance (in ohms) of the motor sense resistor. This parameter -# must be provided. +# The resistance (in ohms) of the motor sense resistor. This +# parameter must be provided. #idle_current_percent: 100 # The percentage of the run_current the stepper driver will be # lowered to when the idle timeout expires (you need to set up the @@ -1726,10 +1728,10 @@ # chip. This may be used to set custom driver parameters. The # defaults for each parameter are next to the parameter name in the # list above. See the TMC2660 datasheet about what each parameter -# does and what the restrictions on parameter combinations are. -# Be especially aware of the CHOPCONF register, where setting CHM to -# either 0 or one will lead to layout changes (the first bit of HDEC) -# is interpreted as the MSB of HSTRT in this case). +# does and what the restrictions on parameter combinations are. Be +# especially aware of the CHOPCONF register, where setting CHM to +# either zero or one will lead to layout changes (the first bit of +# HDEC) is interpreted as the MSB of HSTRT in this case). # Configure a TMC5160 stepper motor driver via SPI bus. To use this # feature, define a config section with a "tmc5160" prefix followed by