mirror of https://github.com/Desuuuu/klipper.git
config: Add BigTreeTech GTR board generic config file (#2626)
This config was not yet available - I have updated all the pin defines, starting with the BTT SKR board which is the most similar board + tested it on my printer which is currently working with the TMC5160 drivers using software SPI. I have not tested it with other drivers etc but the config should work for them. Signed-off-by: Chester Lowrey <hilo90mhz@gmail.com>
This commit is contained in:
parent
acd165cbea
commit
35d951dabf
|
@ -0,0 +1,331 @@
|
|||
# This file contains common pin mappings for the BigTreeTech GTR.
|
||||
# To use this config, the firmware should be compiled for the
|
||||
# STM32F407 with a "32KiB bootloader".
|
||||
|
||||
# The "make flash" command does not work on the GTR. Instead,
|
||||
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the GTR
|
||||
# with that SD card.
|
||||
|
||||
# See the example.cfg file for a description of available parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PC15
|
||||
dir_pin: PF0
|
||||
enable_pin: !PF1
|
||||
step_distance: .0125
|
||||
endstop_pin: ^!PF2
|
||||
position_endstop: 0
|
||||
position_max: 220
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PE3
|
||||
dir_pin: PE2
|
||||
enable_pin: !PE4
|
||||
step_distance: .0125
|
||||
endstop_pin: ^!PC13
|
||||
position_endstop: 0
|
||||
position_max: 250
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB8
|
||||
dir_pin: PB7
|
||||
enable_pin: !PB9
|
||||
step_distance: .0025
|
||||
endstop_pin: ^PE0
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 12
|
||||
second_homing_speed: 1
|
||||
|
||||
[extruder]
|
||||
step_pin: PG12
|
||||
dir_pin: PG11
|
||||
enable_pin: !PG13
|
||||
step_distance: .002
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PB1 # Heat0
|
||||
sensor_pin: PC1 # T0 Header
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 290
|
||||
|
||||
#[extruder1]
|
||||
#step_pin: PD6
|
||||
#dir_pin: PD5
|
||||
#enable_pin: !PD7
|
||||
#heater_pin: PA1 # Heat1
|
||||
#sensor_pin: PC2 # T1
|
||||
#...
|
||||
|
||||
#[extruder2]
|
||||
#step_pin: PD1
|
||||
#dir_pin: PD0
|
||||
#enable_pin: !PD2
|
||||
#heater_pin: PB0 # Heat2
|
||||
#sensor_pin: PC3 # T2
|
||||
#...
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA2
|
||||
sensor_pin: PC0 # BED
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PE5 # FAN0
|
||||
|
||||
[heater_fan fan1]
|
||||
pin: PE6 # FAN1
|
||||
|
||||
#[heater_fan fan2]
|
||||
#pin: PC8 # FAN2
|
||||
|
||||
[mcu]
|
||||
baud: 250000
|
||||
restart_method: command
|
||||
serial: dev/serial0
|
||||
# setup for PA9, PA10 USART1_tx / rx directly connected to the RPI GPIO TX / RX pins
|
||||
# These are the pins the GTR uses for its built in RPI 40 pin connector
|
||||
# only connect GND, TX, RX - supply 5v power to the RPI separately
|
||||
# do not cross over TX/RX - it is done internally on the GTR PCB.
|
||||
# Use "sudo raspi-config" to disable the serial terminal - but enable the serial port.
|
||||
# When running "make menuconfig" you must un-select the USB Serial check box
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 500
|
||||
max_accel: 3000
|
||||
max_z_velocity: 12
|
||||
max_z_accel: 5
|
||||
|
||||
########################################
|
||||
# TMC2208 configuration
|
||||
########################################
|
||||
|
||||
#[tmc2208 stepper_x]
|
||||
#uart_pin: PC14
|
||||
#microsteps: 16
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 250
|
||||
|
||||
#[tmc2208 stepper_y]
|
||||
#uart_pin: PE1
|
||||
#microsteps: 16
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 250
|
||||
|
||||
#[tmc2208 stepper_z]
|
||||
#uart_pin: PB5
|
||||
#microsteps: 16
|
||||
#run_current: 0.650
|
||||
#hold_current: 0.450
|
||||
#stealthchop_threshold: 30
|
||||
|
||||
#[tmc2208 extruder]
|
||||
#uart_pin: PG10
|
||||
#microsteps: 16
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 5
|
||||
|
||||
#[tmc2208 extruder1]
|
||||
#uart_pin: PD4
|
||||
#microsteps: 16
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 5
|
||||
|
||||
#[tmc2208 extruder2]
|
||||
#uart_pin: PC12
|
||||
#microsteps: 16
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 5
|
||||
|
||||
|
||||
########################################
|
||||
# TMC2130 configuration
|
||||
########################################
|
||||
|
||||
#[tmc2130 stepper_x]
|
||||
#cs_pin: PC14
|
||||
#microsteps: 16
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
#[tmc2130 stepper_y]
|
||||
#cs_pin: PE1
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
#[tmc2130 stepper_z]
|
||||
#cs_pin: PB5
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#run_current: 0.650
|
||||
#hold_current: 0.450
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
#[tmc2130 extruder]
|
||||
#cs_pin: PG10
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
#[tmc2130 extruder1]
|
||||
#cs_pin: PD4
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
#[tmc2130 extruder2]
|
||||
#cs_pin: PC12
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
########################################
|
||||
# TMC5160 configuration
|
||||
########################################
|
||||
|
||||
#[tmc5160 stepper_x]
|
||||
#cs_pin: PC14
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#interpolate: True
|
||||
#run_current: 1
|
||||
#hold_current: 1
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
#[tmc5160 stepper_y]
|
||||
#cs_pin: PE1
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#interpolate: True
|
||||
#run_current: 1
|
||||
#hold_current: 1
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
#[tmc5160 stepper_z]
|
||||
#cs_pin: PB5
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#interpolate: True
|
||||
#run_current: 0.4
|
||||
#hold_current: 0.4
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
#[tmc5160 extruder]
|
||||
#cs_pin: PG10
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#interpolate: True
|
||||
#run_current: 0.5
|
||||
#hold_current: 0.5
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
#[tmc5160 extruder1]
|
||||
#cs_pin: PD4
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#interpolate: True
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
#[tmc5160 extruder2]
|
||||
#cs_pin: PC12
|
||||
#microsteps: 16
|
||||
#sense_resistor: 0.075
|
||||
#interpolate: True
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 0
|
||||
#spi_software_mosi_pin: PG15
|
||||
#spi_software_miso_pin: PB6
|
||||
#spi_software_sclk_pin: PB3
|
||||
|
||||
########################################
|
||||
# EXP1 / EXP2 (display) pins
|
||||
########################################
|
||||
|
||||
# display section not tested - pinout should be correct but my LCD did not work yet
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PC11, EXP1_3=PC10, EXP1_5=PG8, EXP1_7=PG6, EXP1_9=<GND>,
|
||||
EXP1_2=PA15, EXP1_4=PA8, EXP1_6=PG7, EXP1_8=PG5, EXP1_10=<5V>,
|
||||
# EXP2 header
|
||||
EXP2_1=PB14, EXP2_3=PD10, EXP2_5=PH10, EXP2_7=PB10, EXP2_9=<GND>,
|
||||
EXP2_2=PB13, EXP2_4=PB12, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>
|
||||
# not sure on this: Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2"
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
#[display]
|
||||
#lcd_type: st7920
|
||||
#cs_pin: EXP1_4
|
||||
#sclk_pin: EXP1_5
|
||||
#sid_pin: EXP1_3
|
||||
#encoder_pins: ^EXP2_5, ^EXP2_3
|
||||
#click_pin: ^!EXP1_2
|
||||
#kill_pin: ^!EXP2_8
|
||||
|
||||
#[output_pin beeper]
|
||||
#pin: EXP1_1
|
Loading…
Reference in New Issue