The gpio_peripheral() code is the same in stm32f0.c, stm32f4.c, and
stm32h7.c. Move that function to a new gpioperiph.c file to avoid
code duplication.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't go above 400Mhz as otherwise it causes 32bit rollover issues.
(Parts of the code expect a rollover will not occur faster than 10
seconds.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Multiplying the desired bitrate by 4 results in half the
desired period and thus twice the desired bitrate.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
This clock is only needed for low-power operation mode,
and wasn't correctly configured anyway (should be 48MHz).
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Commit 9ecddd1b fixed a serious error (introduced in 7d95a004). Force
a protocol version change so users are aware of the need to update the
mcu code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 7d95a004 introduced a defect - if the cached timer pointed to
by last_insert did not reschedule itself then the cache would not be
in a valid state and other active timers may not get properly
rescheduled.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an optimized step function for drivers that support stepping on
both rising and falling edges of the step pin. Enable this
optimization on 32bit ARM micro-controllers. Automatically detect
this capability in the host code and enable on TMC drivers running in
SPI/UART mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove the STEP_DELAY Kconfig option and replace it with a per-stepper
step_pulse_duration printer.cfg config option.
The AVR code will continue to have optimized code to step and "unstep"
in the same function (which is automatically activated when the step
delay is 40 ticks or less). This change removes the Kconfig option
for single function step/unstep on 32bit processors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The floating point unit must be enabled in order to use it and Klipper
does not currently implement that. Newer versions of gcc may spill
registers to the floating point unit causing failures.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The floating point unit must be enabled in order to use it and Klipper
does not currently implement that. Newer versions of gcc may spill
registers to the floating point unit causing failures.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The floating point unit must be enabled in order to use it and Klipper
does not currently implement that. Newer versions of gcc may spill
registers to the floating point unit causing failures.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Tracking of the last reset is no longer needed after commit 8f76e53c.
Remove the code tracking that status and remove the flag definition.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some architectures do better if the global variables accessed from the
timer dispatch code are in a struct.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some versions of gcc, in some cases, decide that it is OK to move the
read to `INTR` to right after clearing the `SETUP_REC` bit of
`SIE_STATUS`, instead of after the `memcpy`.
The rp2040 datasheet doesn't appear to say anything about how quickly
the `SETUP_REC` bit will be cleared in `INTR`, but regardless the
compiler should not be re-ordering the read like this.
Here we force the correct ordering using a memory barrier.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Copy the parameters of calls to console_sendf() on pru1 to pru0 and
then call that function on pru0. Although copying the parameters is a
"hack", the code size reduction is notable.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The F042 and F072 chips are in the same series and the code should be
nearly identical for these chips. Implement the alias and enable USB
for the F072 chips.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The previous OSPEEDR value of 0x2 was copied from the stm32f4.c code,
but the stm32f0 interprets that value the same as 0x0 - which is "low"
speed. Change the OSPEEDR value to "medium" speed so that it matches
the configuration of stm32f1 chips.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This change has been expanded to include all STM32F4 processors, since they share a common TIMER mapping with some processors just not having all of the timers and pins.
Signed-off-by: Jerome Helbert <jerome@helbert.net>
This commit contains a configuration for the Anycubic Vyper printer from 2021.
It uses a clone of the STM32F103 chip named GD32F103.
There are 2 Mainboard versions out there v0.0.5 and v0.0.6, this config has
been tested with the v0.0.6 only. It should probably work for v0.0.5 as well
since there are no different changes in the Anycubic Marlin firmware.
The LCD is not supported yet (might work, but didn't try yet).
Signed-off-by: Marc Neuhaus <marc@neuhaus.nrw>
Signed-off-by: Manuel Fichtner <manuel.fichtner@me.com>
The F405, F407, and F429 chips are in the same series and almost all
code definitions should apply to all chips in that series. Implement
the alias and fix defintions in adc.c and Kconfig that were only
applying to a subset of that series.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Transmit data from mcu to host using 5 bytes per sample and up to 10
samples per message block. This improves bandwidth efficiency.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Query the adxl345 message counter every 100ms so that accurate timing
can be obtained during measurements. This allows the adxl345 data to
be exported with timestamps while captures are running.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This fixes a PWM going to full scale output when a initial value != 0 was
given. The output was on 100% until another update occurred.
This change enables the PWM counter before setting the channel values.
FixesKevinOConnor/klipper#4559
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
The atmega328pb supports PORTE, but the current avr-libc toolchain
doesn't support the atmega328pb. So, for now, add support for PORTE
to atmega328p.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The atmega328pb has officially named these pins as PE2 and PE3, so use
that naming scheme instead of the previous Klipper invented names.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for USART1 on PB7/PB6.
Remove STM32_SERIAL_USART1_ALT_PA15_PA14 option and allow all serial
mappings to be used on stm32f031.
Reported by @Desuuuu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Eryone ER-20 is a STM32F103 based 3D printer which ships with a 16KiB bootloader. Their official version of Marlin starts at 0x08004000.
Signed-off-by: Simon Hawkenson <simon@hawkenson.ca>
This implements SPI for the rp2040 target. All output groupings of both
SPI blocks are available for use.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
This implements hardware PWM support for the rp2040. The maximum
value(100% duty) is set to 255 to match the other controllers. Cycle
time is clamped automatically, and uses the full 8.4 fractional range of
the rp2040 PWM block. This allows a maximum PWM frequency of 490kHz and
a minimum frequency of 1915 Hz.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
The rp2040 doesn't have a chip ID, but the flash chip connected does. We
can get this ID by asking the flash chip directly, but doing so requires
disengaging the XIP layer, performing the interrogation of the flash
chip, and then re-enabling the XIP layer. This gives us a 64-bit unique
ID that we can use as our USB serial number.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
In binutils 2.36 and above the -nostartfiles option is no longer
ignored. -nostartfiles is actually a gcc option, and so isn't supported
by ld. Earlier versions of binutils however had less error checking, and
thus just ignored the option.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Support the rp2040 (as tested on a Raspberry Pi Pico board). This
adds basic uart, timer, gpio, and watchdog support.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use CONFIG_MACH_AVR instead of CONFIG_CLOCK_FREQ to check for slow
mcus. Some fast MCUs do not export a high clock frequency.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* Add menuconfig option for stm32f072
* Add support for internal temp of stm32f072
* Share the temperature calculation logic between stm32f0x2 MCUs
Signed-off-by: Erik Henriksson <erikhenrikssn@gmail.com>
This reverts commit 70ea0806d9.
The above commit breaks software spi on linux hosts. Revert that
commit until an improved error check can be implemented.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 6a3c357a incorrectly disabled support for USART3 on stm32f1 and
stm32f2 - restore that support.
Also, add support for USART3 on PD9/PD8 on stm32f103.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
These commands were never used by the main code and are not
particularly helpful for debugging. Remove them to reduce code size -
in particular on the pru architecture.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit ae89a659 caused a regression in the lpc176x UART handling.
After that commit the UART clock divisor would need to be 6.25 on
lpc1768 or 7.5 on lpc1769, but the code only supports whole numbers.
Set the PCLKSELx registers at startup and return to using full speed
peripheral clocks.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
adelyser
adelyser
Alex Maclean
Eric Callahan
Lasse Dalegaard
jrhelbert
Manuel Fichtner
Simon Kühling
D4SK
Michael Kurz
Simon Hawkenson
Henky Prayoga
henrikssn
github@matthewlloyd.net
Sergey Alirzaev
Wilhelm Schuster