Add support for writing back the main printer config file with
additional calibration data stored in it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a command that will turn off all heaters in the printer. Run this
command in the default idle_timeout action.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the document to recommend tuning with decreased acceleration
and with square_corner_velocity disabled. Using this approach makes it
possible to test with significantly higher pressure advance values.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This can be flashed to e.g. the duet wifi using bossac. It requires a
later version as is currently included in the klipper repo (1.8
vs. 1.2). Comms are currently via UART0 only, USB serial is still TBD
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
The Todo.md file has gotten stale, and it is no longer an effective
mechanism for tracking changes. Remove it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add initial support for commands that will forcibly move a stepper
(without updating the kinematic classes with the new position).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The junction_deviation configuration parameter has a number of quirks
that make it difficult to configure. Replace it with a
"square_corner_velocity" configuration parameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add M117 and M73 to the list of supported G-Codes.
Also, remove M117 from the list of commands reported by the HELP
command as that command is typically only used to list "extended
g-code" commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add basic SPI support and associated documentation.
v2: remove baud rate check, fix baud rate calculations
v3: finish transaction with BSY check, disable SPI when not in use
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
The PRU code size has grown too close to the maximum - remove the ADC
code to reduce its overall size. (On the beaglebone, the Linux
process can, and typically does, do the ADC reading.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for an itersolve_set_position() function that sets a
stepper position from a cartesian coordinate. This eliminates the
need for both the python and C code to be able to translate from a
cartesian coordinate to a stepper position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Calculating the cartesian position from the stepper positions can be
complex and cpu intensive, so rename it to calc_position() to be more
descriptive.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When using multiple micro-controllers it may be necessary to use an id
from /dev/serial/by-path/ instead of /dev/serial/by-id/. Also,
emphasize that in config/example-multi-mcu.cfg.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the get_status command to get_clock. Don't report the shutdown
status in the new get_clock command.
The primary purpose of this change is to force the host code to report
a firmware version mismatch with older firmwares as recent changes
(namely the ordering of message block acks) have subtle
incompatibilities if different host/mcu code is used.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the new gcode.register_mux_command() so that SET_PRESSURE_ADVANCE
works correctly with multiple extruders.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improve the SPI message transmit system. Add support for bus speed
and bus mode. Add support for sending SPI messages on shutdown.
Signed-off-by: Petri Honkala <cruwaller@gmail.com>
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the C code out of the main klippy/ directory and into its own
directory. This reduces the clutter in the main klippy directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M206 command is confusing (it uses negative offsets) and isn't
very flexible. Add a new SET_GCODE_OFFSET command to make it easier
to add virtual offsets to gcode commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Drop support for M303 and PID_TUNE, and replace it with a new
PID_CALIBRATE command. Move the logic for this command from heater.py
to a new pid_calibrate.py file in the extras/ directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It looks like OctoPrint is expecting the result from M114 to be
relative to the last G92 command. Also, introduce GET_POSITION to
report the actual location that the printer is at.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Emphasize that the log file needs to be attached to the issue.
Encourage M112 to be issued on every bug report.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's common for multiple steppers to use the same stepper enable
line. Detect this and only create a single digital_out oid on the
micro-controller.
Also, prohibit any other pin from being used multiple times in the
config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the pressure advance tuning document to note that 0.20 is
likely the ceiling of a useful pressure advance setting.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Provide a document with basic steps that a user can run to verify that
the pins in the configuration file are set correctly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an initial document detailing best practices for contributing to
the document. Add the "developer certificate of origin" document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Try to make the Installation document more friendly to users not
familiar with the Linux command-line. Offer some hints on how to
obtain ssh and how to edit the config file remotely.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add additional notches and move them to the inside of the square where
they will not impact the outside perimeter test.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow the start value to be different from the default/shutdown value
for the pin. This will be useful for "heater fans" that should
startup in the off state, and transition to full on in a shutdown
state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Pass the sample_ticks and sample_count parameters directly in the
end_stop_home command instead. This simplifies the code.
Also, simplify calculation of next wakeup time in
end_stop_oversample_event().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Place a small notch on one side of the square. The notch provides
interesting information on the extruder performance, and it makes it
easier to compare with previous prints of the object.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Several items were recently implemented. Remove the "cubic vs
quadratic" item as investigations into cubic compression weren't
promising.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for configuring and controlling the hardware specific to
the revision "B3" Replicape board.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement the conversion from print_time to the local mcu's clock
within the C code. This simplifies the python code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Extend the look-ahead mechanism to work between moves that contain Z
movement. This improves Klipper's handling of g-code produced in
"vase mode".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It should no longer be necessary to configure "custom" commands during
mcu setup. The ad5206 and static_digital_output config sections
should provide similar functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Compile the PRU binary with -Os optimization, but request that the
timer dispatch code be compiled with -O2 optimization. This improves
the performance of timers slightly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The gcc -Os option significantly reduces the size of the PRU binary
and it has little impact on performance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is not necessary to limit stepper acceleration - only the limiting
of stepper torque is important.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a CONFIG_SIMULAVR option to the Kbuild menus and don't directly
prompt users for CONFIG_WATCHDOG or CONFIG_SERIAL_BAUD_U2X. The only
reason to disable these options would be if one were running on
simulavr. This simplifies the user visible menu options.
Also, only show CONFIG_CLEAR_PRESCALER for at90usb1286 chips.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of assuming the maximum PWM value is 255, export a constant
from the firmware to the host with the maximum value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Those that reach Klipper via github may jump directly to the docs/
directory in search of documentation. Add README.md and rework
Overview.md with that in mind.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The term "firmware" is ambiguous - it could refer to the entire
project (host and micro-controller software) or to just the
micro-controller software. Avoid the term in the documentation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Klipper software has progressed to the point where it does not
need to be described as "experimental" software.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Detect avr gcc v4.8.1 and then disable warnings during the klipper.o
linking to suppress bogus "misspelled signal handler" warnings.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a system startup script so that Klipper can automatically start at
boot time. Create an installation script that will install the system
dependencies and the startup script.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Florian Heilmann
Arksine
Grigori Goronzy
Grigori Goronzy
Michael Barbour
Dave Bacon