Add a pin definition to enable motor power and add a warning about
initial faulty SKR2 boards.
Reported by @FHeilmann.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds Duet3 Mini Config with support for expansion header
Signed-off-by: Luke Ashley <Luke@Lukeslab.online>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
To support continuous belt printing, add nestable repeat
loop support via an `[sdcard_loop]` module.
Supported G-Code:
- SDCARD_LOOP_BEGIN COUNT=n ; Loop for N times, or infinitely if N is 0
- SDCARD_LOOP_END ; End of loop
- SDCARD_LOOP_DESIST ; Complete all loops without iterating
Marlin M808 compatibility example in `config/sample-macros.cfg`:
- M808 Ln ; Loop for N times, or infinitely if N is 0
- M808 ; End of loop
- M808 K ; Complete all loops without iterating
Added unit tests in test/klippy/sdcard_loop.test
See https://reprap.org/wiki/G-code#M808:_Set_or_Goto_Repeat_Marker
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
Change all the example config files to use either 0 or 999999 for
stealthchop_threshold (as is recommended in the TMC_Drivers.md
document).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for the Creality CR-30 'PrintMill', and its base board,
the Creality v4.2.10.
Add them to the `test/klippy/printers.test` test suite
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
A working configuration example for Tronxy X5SA Pro printer (https://tronxy.com/x5s-series/x5sa-pro.html) with no Touchscreen funcionalities because separated LCD firmware needed.
Silent TMC2225 drivers soldered on board.
The Self-levelling plate sensor is a blue Tronxy XY-08N model.
Direct Drive is a Titan Extruder Clone "3:1" gear ratio.
Signed-off-by: Morgan Barresi <morganfw@gmail.com>
Improvements and fixes based on feedback:
* Make speeds and limits more conservative
* Fix Y endstop position
* Improve IR bed leveling
* Fix filament runout pin
Signed-off-by: Justin Schuh <code@justinschuh.com>
Create a sample-aliases.cfg with all the aliases that are currently
hardcoded in the klippy.pins.py module.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This adds support for BMP280 and BME680 sensor ICs,
along with fixing calibration data readout for BME280.
Gas sensor readout for the BME680 is just the raw compensated value.
To get actual meaningful values, more research is needed.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
A working configuration example for Hiprecy Leo printer (https://www.hiprecy.com/product/402/) with no Touchscreen funcionalities because separated LCD firmware needed.
TMC2130 SPI drivers.
The Self-levelling plate sensor is PINDA probe type
Direct Drive is a BMG "3:1" gear ratio
Signed-off-by: Morgan Barresi <morganfw@gmail.com>
There are two fan pins on Robin Nano 3 and the fan1 pin is PC14, not PB1.
PB1 pin that was in config example is used for the fan2 output.
Signed-off-by: Oleksii Zelivianskyi <alexeyzel@gmail.com>
we just found a small problem: Some people have slightly higher endstop positions, which caused them to have a move out of range during probe calibrate.
Signed-off-by: Christoph Frei <fryakatkop@gmail.com>
Fixed bltouch offset and bed_mesh mesh_min/max to account for offset.
The former was defined in the wrong coordinate, as the origin starts from the SW. The latter did not include the offset and caused an error. Technically the offset allows mesh_max up to (239.3, 253).
Signed-off-by: Ben Kaye <benkaye001@gmail.com>
Add generic-bigtreetech-gtr.cfg to printers.test. Add definitions for
thermocouple and temperature_mcu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Added Ender 3 Max config. Based off the configs from ender6, ender3-v2, and ender3. Also contains optional BLTouch parameters.
Signed-off-by: Chad Schwieterman <chad.devops@gmail.com>
The Lulzbot TAZ6 single extruder configuration had an XY position for
z homing that did not match the factory firmware, and was off center
enough to cause the extruder to crash into the home button trim
sometimes when homing. This commit changes the printer config so
that the XY position for Z homing matches the original Marlin firmware
for this printer.
The Lulzbot TAZ6 single extruder configuration had an bed_tilt points
that did not match the factory firmware, and were off enough that the
nozzle (used for probing on this printer) could slip off the edge of
the probe point or miss it entirely. This commit changes the printer
config so that the coordinates for bed_tilt calibration match the
original Marlin firmware for this printer.
For the Lulzbot TAZ6 single extruder config, use 'gear_ratio' and
'rotation_distance' to configure the extruder.
The rotation distance is based on effective circumference of the hobbed
bolt based on the original Marlin firmware for the TAZ6 single-extruder,
and the gear ratio was determined by simply counting the number of
teeth on the pinion and spur gears.
Signed-off-by: Steven T. Snyder <github@steventsnyder.com>
Add support for automatically calculating the internal step_distance
from new config parameters - rotation_distance, microsteps,
full_steps_per_rotation, and gear_ratio.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Minor indentation changes and remove default values for heater_fan.
Add to printers.test test cases.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds config for the Monoprice Select Mini v2 cartesian printer. I have
successfully tested the configuration.
Signed-off-by: Kilian Neuner <github@9-r.net>
Add an 'mcu' option to the board_pins config and use that to specify
the name of the mcu to apply the aliases to. Support applying the
aliases to multiple mcus.
Add support for any number of options starting with an "aliases_"
prefix.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move all the config reference information from files in the config/
directory to a new Config_Reference.md document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
squeekyzebra
github@matthewlloyd.net
Kevin O'Connor
KoeRt888
James Churchill
Clark Tomlinson
Luke's Lab
TheBugLebowsky
Jason S. McMullan
jericho-adler
Marco Robustini
Pranas Kiziela
Jelle Victoor
Wilhelm Schuster
Tircown
George Fu
C. Bluoss
le-Bark
popshansen
Demetrius Apostolopoulos
Justin Schuh
Tomas Rimkus
Michael Kurz
Bob90
Oleksii Zelivianskyi
FrY Sennberg
Ben
Chad Schwieterman
Steven Snyder
Timothée Girard
Sean McGroty
9R
Raabi91
Jeff Tang