Add a sample-lcd.cfg with the defintions for several common "reprap"
style LCD displays that use the EXP1/EXP2 plugs. Update several
config files to add EXP1/EXP2 board aliases.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The current z_hop support did not work correctly with common slicers
that change Z height between retract and unretract, and it did not
work correctly with slicers that issue a retract at the end of a print
and then at the beginning of the next print.
The z_hop support is therefore being removed until these issues can be
fixed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for enabling the stepper via the communication channel.
This improves support for boards with a shared enable line.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
An extra to execute gcode when a hardware button is pressed or released. Uses the jinja2 templating system.
Inspired by pull request #545 from Miguel Moitinho miguel@moitinho.net and pull request #1098 from Paulo Drugos paulodrugos@gmail.com
Signed-off-by: Alec Plumb <alec@etherwalker.com>
Support retrying Z_TILT_ADJUST a configurable number of times
to a configurable tolerance both in the config or as parameters.
- By default keeps original behavior of no retries.
- Adds parameters RETRIES and RETRY_TOLERANCE to QUAD_GANTRY_LEVEL gcode.
- adds config options retries and retry_tolerance to uad_gantry_level]
- issues an error if we are getting worse intead of approaching tolerance
- issues an error if retries were requested but we did not reach the tolerance
in the specified number of retries
the minimum change should be a single z step for those
probing 2 points for 2 stepper motors and 3 for 3 stepper motors.
at one point it was suggested to use the amount of z adjustment instead of the
range of the probed points as a trigger for retry. I've chosen not to do this.
using z adustment in these cases means the minimum unit of change is related to
the angle created by the probed points and the distance to stepper motor and
can be more than a couple steps which is rather unintuitive.
for the case when someone is using more probed points than z steppers the
probed points range will have some fixed minimum value that can't be reduced
which is also unintuitive but that case should idealy be the rarer case, and
the user can learn to set a higher tolerance that matches their probing setup.
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
Support retrying QUAD_GANTRY_LEVEL a configurable number of times
to a configurable tolerance both in the config or as parameters.
- By default keeps original behavior of no retries.
- Adds parameters RETRIES and RETRY_TOLERANCE to QUAD_GANTRY_LEVEL gcode.
- adds config options retries and retry_tolerance to `[quad_gantry_level]`
- issues an error if we are getting worse intead of approaching tolerance
- issues an error if retries were requested but we did not reach the tolerance
in the specified number of retries
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
No need to describe the SET_TMC_CURRENT command in the
example-extras.cfg - it's describe in docs/G-Codes.md and is now
supported on all tmc drivers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
List all the configurable parameters in the tmc5160 example block and
use similar wording as the other tmc drivers.
Also, don't allow DEDGE to be configured as it would just break the
current code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This changes the config file so that the configuration of
multi-samples is now done in the [probe] (and [bltouch]) section
instead of the various delta, bed_mesh, z_tilt, etc. config sections.
With this change, PROBE and PROBE_CALIBRATE commands now also utilize
multi-sampling.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Reformat some of the comments. Add section headers. Don't comment
out the config sections (so that it is more clear what needs to be
copied to the main config).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There are reports that SPI does not work correctly on the Fysetc F6 if
the PB0 (sdcard cs enable line) isn't pulled high. Update the default
config to enable that line.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This config is based on the existing Ender 3 example config but some of
the directions for the steppers have been reversed. It works for me so
far, but feel free to modify.
Signed-off-by: Billy Jones <billyajones@gmail.com>
Minor updates to the kit-zav3d-2019.cfg to make it look more like
other config files: specify the micro-controller type, use the
klipper3d.org site for documentation links, avoid using SAVE_CONFIG
sections in the example configs, add config to printers.test.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Zav3d - a popular russian corexy plywood printer.
Official web site is https://www.zav3d.ru/
Social network community is https://vk.com/zav3d
Signed-off-by: Nurmukhamed Artykaly <nurmukhamed.artykaly@hdfilm.kz>
safety feature that prevents quad_gantry_level from trying to do a
correction that might break things - if your probe fires early for
whatever reason and tries to do an 8mm correction in one corner instead
we abort if a correction is over a configurable limit by default 4mm
configurable via `max_adjust` parameter in the config
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
The servo pins (P9_14/P9_16) are muxed to the SOCs hardware PWM unit
driven by a 13MHz GP timer. They have to be driven by the linux host
mcu. This commits adds hardware PWM support using the linux sysfs
user space interface.
The servo pins can be specified as "replicape:servo0" and
"replicape:servo1". Removes the "servo0_enable", "servo1_enable"
configuration parameters.
Fixes#1105.
Signed-off-by: Janne Grunau <janne-3d@jannau.net>
Adds parameter for bed meshes to be adjusted relative to a probed point
during calibration. This allows the probe z offset to be ignored for
probes that are not stable over time (for example, the thermal drift of
inductive probes). An endstop other than the probe is then necessary to
determine the bed-nozzle offset.
Signed-off-by: Matt Baker <baker.matt.j@gmail.com>
Use the field names from the trinamic specification. This makes the
field similar to all the other driver_XXX config options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
sense_resistor is now a mandatory parameter for tmc2660 blocks. Duet2 users should use a value of 0.051
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Using the Duet2 config as a base for your own config will no longer turn
on all heaters and fans at full power during the (almost inevitable) MCU
shutdown that will occur during initial Klipper setup.
Signed-off-by: Benoit Miller <github@benoitmiller.ca>
Support reading a "gcode_id" parameter from heater/sensor config
sections.
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The 'bed_shape' option has been removed. The user will enter a 'bed_radius' if they have a round be, otherwise they should enter 'min_point' and 'max_point'. When the bed is round the user should supply a 'round_probe_count' option, otherwise just 'probe_count'.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Support added for filament diameter sensor. Sample configuration parameters added to example-extras.cfg.
Signed-off-by: Mustafa YILDIZ <mydiz@hotmail.com>
Adds the ability to register a custom/generic heater through a new extra called heater_generic.
This takes a gcode_id that is reported by M105. Adds a new command to set the temperature for any heater using the syntax:
SET_HEATER_TEMPERATURE HEATER=<heater_name> TARGET=<target_temp>
Signed-off-by: John Jardine <john@gprime.net>
Example config file for a stock 250mm build VORON2 printer that
matches the manual diagrams exactly for the controller layout and pins
used.
Signed-off-by: Ben Warren <boffdroid@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Marlin examples use the "ATC Semitec 104GT-2" thermistor for the CR10,
CR10S, and CR10mini. Reported by @dovcharov.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add updates to example-extras.cfg and G-Codes.md documenting pause_resume. Also add M600 (filament change) to sample-macros.cfg.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Add support for performing linear interpolation between a set of
measured temperature/resistance pairs.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the undocumented test_sensor_pin config option into a
pin_up_touch_mode_reports_triggered option and document it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Query the bltouch state during the pin_up command to try and verify
that the probe does actually retract. This may be useful to detect if
the bltouch enters into an "error" state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Whenever a stepper driver or a heater becomes active, it is desirable to turn on a fan cooling the associated parts on the controller board. This module implements such a fan that turns on whenever a stepper or specified heater turns on, decelerates to a configurable speed when all of the watched parts turn off, and returns to an off-speed, when a user-defined timeout is met.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
This is my current config file for Fysect F6 + TMC2208 running on my
Ender 3 with stock creality display.
Signed-off-by: Simone Bonacini <bonacini.simone@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
- changes that make easier to use menu as module UI
- new helper method for delayed callbacks
- method for getting the menu instance from display
- new action for sending menu:action events
- allow_without_selection option for cards
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
- long press with timer (button release is not needed anymore)
- initial support for edit mode long press gcode
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
The sam3 i2c code and the linux code use a 7-bit i2c address, while
the avr, lpc176x, and samd21 i2c code uses an 8-bit address with the
least significant bit always zero. A similar issue occurred in the
host code (sx1509.py and replicape.py use 7-bit addresses while
uc1701.py and mcp4451.py use 8-bit addresses).
Consistently use 7-bit addresses in all the code. This breaks
compatibility between host and mcu software, so make a change to the
config_i2c command to force users to synchronize software updates.
This also breaks common Smoothieboard configs, so update the mcp4451
code to validate the i2c_address.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
I have made one change to `gcode.py` to support quoted parameter
values.
I have added support for the basic `M118` command (see
https://reprap.org/wiki/G-code#M118:_Echo_message_on_host). I have
also added a `RESPOND` command that takes extended parameters.
`ECHO` might be a better name than `RESPOND` but is already defined
in `gcode.py`.
Signed-off-by: Alec B. Plumb <alec@etherwalker.com>
Kevin O'Connor
Florian Heilmann
Arksine
Alec B. Plumb
fess
Hywelmartin
nzlrhyz
Len Trigg
Stephan
Billy Jones
Nurmukhamed Artykaly
Dmitry
Janar Sööt
Janne Grunau
Aleksander Sobolewski
Douglas Hammond
Montbel
Matt Baker
Rui Caridade
Benoit Miller
nopbit
John Jardine
Boffgithub
AxMod 3D Print
Tschipel
Ales Stimec
Rui Caridade
Master92
SimoneBnc
Yannic Schröder
Patrick Balsiger
Graham Ambrose