config: Add example SKR mini-E3 config

Signed-off-by: Ashley Izat <ashleyi100@googlemail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
Kevin O'Connor 2019-07-31 13:04:13 -04:00
parent c95209bf7a
commit f21f66a31f
2 changed files with 127 additions and 0 deletions

View File

@ -0,0 +1,126 @@
# This file contains common pin mappings for the BIGTREETECH SKR mini
# E3. To use this config, the firmware should be compiled for the
# STM32F103 with a "28KiB bootloader". Also, select "Enable extra
# low-level configuration options" and configure "GPIO pins to set at
# micro-controller startup" to "!PC13".
# The "make flash" command does not work on the SKR mini E3. Instead,
# after running "make", copy the generated "out/klipper.bin" file to a
# file named "firmware.bin" on an SD card and then restart the SKR
# mini E3 with that SD card.
# See the example.cfg file for a description of available parameters.
[stepper_x]
step_pin: PB13
dir_pin: PB12
enable_pin: !PB14
step_distance: .0025
endstop_pin: ^!PC0
position_endstop: 0
position_max: 200
homing_speed: 50
[tmc2209 stepper_x]
uart_pin: PC11
tx_pin: PC10
uart_address: 0
microsteps: 16
run_current: 0.800
hold_current: 0.500
stealthchop_threshold: 250
[stepper_y]
step_pin: PB10
dir_pin: PB2
enable_pin: !PB11
step_distance: .0025
endstop_pin: ^!PC1
position_endstop: 0
position_max: 200
homing_speed: 50
[tmc2209 stepper_y]
uart_pin: PC11
tx_pin: PC10
uart_address: 1
microsteps: 16
run_current: 0.800
hold_current: 0.500
stealthchop_threshold: 250
[stepper_z]
step_pin: PB0
dir_pin: PC5
enable_pin: !PB1
step_distance: .0125
endstop_pin: ^!PC2
position_endstop: 0.5
position_max: 200
[tmc2209 stepper_z]
uart_pin: PC11
tx_pin: PC10
uart_address: 2
microsteps: 16
run_current: 0.800
hold_current: 0.500
stealthchop_threshold: 5
[extruder]
step_pin: PB3
dir_pin: PB4
enable_pin: !PD2
step_distance: .002
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PC8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA0
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 250
[tmc2209 extruder]
uart_pin: PC11
tx_pin: PC10
uart_address: 3
microsteps: 16
run_current: 0.800
hold_current: 0.500
stealthchop_threshold: 5
[heater_bed]
heater_pin: PC9
sensor_type: ATC Semitec 104GT-2
sensor_pin: PC3
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: PA8
[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
[static_digital_output usb_pullup_enable]
pins: !PC13
[board_pins]
aliases:
# EXP1 header
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
# See the sample-lcd.cfg file for definitions of common LCD displays.

View File

@ -85,6 +85,7 @@ CONFIG ../../config/generic-smoothieboard.cfg
# Printers using the stm32f103
DICTIONARY stm32f1.dict
CONFIG ../../config/generic-bigtreetech-skr-mini.cfg
CONFIG ../../config/generic-bigtreetech-skr-mini-e3.cfg
# Printers using the PRU
DICTIONARY pru.dict host=linuxprocess.dict