The default on X86 32bit machines is to use 80bit floating point math
(as found in the ancient "387 coprocessor"). This can cause numerical
stability problems. Set the compiler flags to make sure the newer SSE
math is always used on X86.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add get_status wrapper with last_query status for macros It is sometimes useful to determine the state of the probe from a macro. If the probe is connected to an endstop pin, the results can be obtained via QUERY_ENDSTOPS but if a physical endstop is in use in addition to the probe the probe state cannot be obtained. This change allows one to use QUERY_PROBE and then access the printer.probe.last_query object to obtain the state.
Signed-off-by: Paul McGowan <mental405@gmail.com>
Some mcu implementations don't like it when the pwm pin is configured
twice, so use the normal schedule_pwm_out implementation to update on
a restart.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Try to invoke a shutdown on an unhandled exception from reactor.run().
If that fails, try to do a clean exit.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update callers to use the printer.command_error reference instead of
directly using homing.CommandError() when raising or catching errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There's no reason to distinguish between an EndstopError and a
CommandError, so just use CommandError.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The optimized version is only available if it's the only axis used.
This fixes input_shaper on corexz.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Combine the shaper pulses and count of those pulses into a `struct
shaper_pulses`. Allocate space for the maximum number of pulses in
`struct input_shaper`.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Increase the maximum redraw rate from 4 times per second to 10 times
per second. Some users have reported slower rendering times as a
result of 8fa1c977.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Split up the main GCodeParser class into GCodeDispatch and GCodeMove
classes. The GCodeMove class is now available using the "gcode_move"
printer object name. This split simplifies the gcode.py code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The "status" and "printing_time" are now available in the
"idle_timeout" module, so no need to report them from toolhead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename printer.gcode.action_emergency_stop() to
action_emergency_stop(), printer.gcode.action_respond_info() to
action_respond_info(), and printer.gcode.action_respond_error() to
action_raise_error() in command templates.
This simplifies the get_status() interface, as returning callable
functions from that interface was confusing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a helper function for submitting relative movements. This
function will also automatically ensure gcode.reset_last_position() is
called.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Generate a "toolhead:set_position" event on a call to
toolhead.set_position() and use that event to automatically call
gcode.reset_last_position().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a request_redraw() method and call it when a key menu event
occurs. Limit these proactive screen redraws to no more than 4 per
second.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
After reading the first item of self.filament_array, filament_width is updated back to self.nominal_filament_dia or self.diameter instead of retaining the value until next pending_position.
Updated Filament Menu Template.
Signed-off-by: Nicola Falciani <nicola.fal@gmail.com>
- don't populate all items at once
- populate items when container is pushed to stack
- precreate List back item, don't create it during populate.
- don't update items during populate
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
Clients can now subscribe to the webhooks get_status() info to
determine if the printer state changes. It is no longer needed to
send a message to all clients on a shutdown transition.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement a new subscription system for get_status() updates.
Subscriptions are per-client. After an initial update, only changes
will be transmitted. Responses are only transmitted to the client
that issued the subscription.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a new "gcode/subscribe_output" webhook endpoint to subscribe to
gcode output. Only client connections that subscribe to the gcode
output will receive that output.
This also moves all the gcode webhooks from gcode.py to webhooks.py
and arranges for gcode.py to be initialized prior to webhooks.py.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the "info" webhook to pass critical process information back to
the caller. The remaining users of register_static_path() can get the
required information via get_status() calls.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't default to "/tmp/klippy_uds" for the webhooks unix domain socket
filename. Instead, require the filename to be specified on the
command-line (via a new "-a" parameter).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
In case of an overwriting existing menu item,
the new item was added additionally to the end of the items list.
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
This prevents ClientConnection.send() from blocking, removing the possibility that callers become reentrant.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
menu.cfg:
- jinja2 template scripting
- new Setup menu
- new Calibration menu
menu:
- redesigned menu code
- jinja2 support
- option to reverse menu up and down directions
- functionality set to support menu injection from other modules
- a new way of defining menu hierarchy
- other adjustments
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
Use a more strict check for determining if the iterative solver has
correctly found a step - the guess must be within 1 picometer of the
target or correct to within 1 nanosecond.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This prevents some cases where the iterative solver fails to converge
in a reasonable time, causing "no next step" errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Arc travel was working but extrusion in absolute mode seemed not to be happening at all. This was because the E coord being sent with each G1 segment of the arc was not incrementing, effectively the same value was being sent over and over so the total extrusion for the whole arc was the amount for just one segment which is an extremely tiny amount.
My change increments e_base by e_per_move for each subsequent coord when in absolute extrude mode which results in the correct absolute E value being sent for each segment.
Signed-off-by: Toby Harper <toby@fuith.org>
This class provides endpoints that allow connected hosts to fetch the state of printer objects and subscribe to state "pushed" over the connection.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Move the pseudo-tty IO handling from the main gcode class to a new
gcode_io class. This simplifies the main gcode class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If there isn't a reader of the output pipe it can lead to the
generation of a large number of errors. Only attempt to write if it
appears the pipe is active.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
SDCARD_PRINT_FILE allows Klipper to load and start the print for any
gcode file within the virtual_sdcard path, including subdirectories.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
In it's current behavior, safe_z_home will attempt to home Z if it thinks the toolhead is above the z endstop even if the motors have since been disabled and the toolhead was moved to another position
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
This streamlines the BedMeshCalibrate class, making it only resposible for configuring and executing the calibration procedure.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Using the setup_start_value() method avoids the PWM output line
transitioning to an intermediate state prior to setting the initial
value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This makes sure output pins are reset to their defaults when the host
is restarted and the micro-controller is not.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a new "on_restart" parameter to mcu.add_config_cmd() and only send
those commands on a host restart that does not involve a
micro-controller restart.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add user-configurable contrast, vcomh (affects "smearing"), and invert options for SSD1306/SH1106 type OLED displays.
Signed-off-by: James Esau <james_esau@hotmail.com>
For example, Raspbian GNU/Linux 8 (jessie) uses an old GCC version 4.9.2
which uses -std=gnu90 by default.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Changing this check from debugoutput to debuginput allows remote applications to perform tests against Klippy without an MCU connected.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Input shaping can help to reduce printer vibrations due to resonances
and eliminate or reduce ghosting in prints.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Register API endpoints for "pause_resume/pause", "pause_resume/resume" and "pause_resume/cancel".
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
If a shutdown occurs during a PID_CALIBRATE command (eg, due to a
heater problem) then exit cleanly instead of throwing an internal
error.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change write_graphics() from taking one pixel row of n characters to
taking all the rows and columns for one character cell.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit allows to modify the icons (or glyphs) in the displays that
support it. Existing icons can be modified and new icons can be added via
a [display_glyph] section in the config.
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Rework extruder.get_trapq() into extruder.sync_stepper() so that
extruder_stepper.py does not need to directly access the extruder
internals.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Option for using the current diameter instead of nominal while the first measurement isn't in place
Signed-off-by: Matthias Pabel <matthias.pabel@hs-augsburg.de>
This reverts commit 43fa41c1af.
The above commit disabled absolute extrude moves because it was
unclear if the code would work properly when an M221 extrude factor or
G92 offset was in use. However, since the calculation is done
relative to the raw E position and is sent as a raw E position to
gcode.cmd_G1() these modes should not matter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If self.kin_flush_delay changes after a G4 dwell command (or other
non-kinematic time update) then it could lead to "internal step
compression" errors. Make sure to handle this case in
flush_step_generation().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make it clear that gcode.get_status() to be called without an
eventtime by defaulting eventtime=None.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store a reference to the gcode class in self.code. Obtain the
z_offset once and use for both the oldval and newval calculation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 9530373c introduced a minimum value of zero for the g-code z
position. Unfortunately, that would likely cause the tuning tower to
not emit a command at the start of a test because the initial dummy z
position is set to a negative value. The minimum bound should not be
needed so remove it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This gives it parity with heater_fan. Also change the default speed from
max_power to 1.0, since it is already scaled by max_power in set_speed.
Signed-off-by: Adrian Keet <arkeet@gmail.com>
Commit c3899cef inadvertently broke the error check for unused config
options. Add a new note_valid parameter to the config access wrappers
and use that in get_status() to fix the check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
round to only 6 decimal places of precision. prevents doing extra retry
from small variations due to floating point math.
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
Always disable the PWM after each command sent. Automatically trim
the command duration so the PWM disable doesn't increase the total
pulse time (when the duration is 200ms or greater).
Track the ideal command end time separately from the pwm transmit time
and only delay toolhead moves to this ideal time.
Update verify_state() to automatically schedule the check using the
time of the last sent command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename try_load_module() so that it uses consistent naming for
"printer objects". Change the function to raise an error by default
if the specified module does not exist.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove the parsing helpers from the main gcode class now that all
callers have been converted to use the parsing helpers in the
GCodeCommand class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Arksine
Kevin O'Connor
Paul McGowan
rjpatawaran
Adrian Keet
Janar Sööt
alocin73
Bryan Boettcher
Trevor Jones
Toby Harper
bondus
Florian Heilmann
Voron
combolek
Iakabos
Dmitry Butyugin
Denis Ignatenko
theophile
matpab
Rubens Panfili
fess
Nathan Plamondon