Raise a printer.config_error() on an invalid register_command() call.
This error is easier to handle for the vast majority of callers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implementation of "PROBE_ACCURACY" to measure the maximum, minimum,
average and standard deviation of a probe.
Signed-off-by: Rui Caridade <rui.mcbc@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The cpu is almost always 16Mhz and the serial port is almost always
UART0, so no need to prompt in the normal case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the internal DWT timer is used for software timers, there is
no need to clock the peripherals at a higher clock speed. Clock all
peripherals at 48Mhz and simplify the clock generation code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Clearing the watchdog while it is in progress can cause bus stalls on
the SAMD21. It appears that clearing the watchdog on the SAMD51 can
cause lockups of the watchdog device.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
These two options don't provide any value and it is causing confustion
with some users. Remove the buttons.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support added for filament diameter sensor. Sample configuration parameters added to example-extras.cfg.
Signed-off-by: Mustafa YILDIZ <mydiz@hotmail.com>
Adds the ability to register a custom/generic heater through a new extra called heater_generic.
This takes a gcode_id that is reported by M105. Adds a new command to set the temperature for any heater using the syntax:
SET_HEATER_TEMPERATURE HEATER=<heater_name> TARGET=<target_temp>
Signed-off-by: John Jardine <john@gprime.net>
Example config file for a stock 250mm build VORON2 printer that
matches the manual diagrams exactly for the controller layout and pins
used.
Signed-off-by: Ben Warren <boffdroid@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Marlin examples use the "ATC Semitec 104GT-2" thermistor for the CR10,
CR10S, and CR10mini. Reported by @dovcharov.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
- When using absolute extrusion the gcode position e-axis position is now captured on PAUSE and restored in RESUME with a call to the G92 handler.
- Add a get_status() function that returns a dictionary with an 'is_paused' key.
- Do not allow consective calls to PAUSE or RESUME to exectue. Also do not allow a RESUME to executed without a previous PAUSE.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
The sram matrix configuration is, bizarrely, configured with a slow
default. It will typically add an extra wait state to every memory
access. Set the matrix sram controller to improve the performance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Avoid using the "low-level" library timing utilities. This is in
preparation for using SysTick as part of the timer implementation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The ARM CortexM3 (and later) chips almost always have a 32bit timer in
the "Debug and Watch Trace" (DWT) unit which resides within the cpu
core itself. This timer is generally faster to access than timers
located on the chip's peripheral bus. When combined with the standard
ARM SysTick timer it provides a (generally) portable mechanism to
implement Klipper's software timer mechanism. It's generally also
faster than using the vendor specific timers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Rui Caridade
christian mock
nopbit
John Jardine
Boffgithub
Florian Heilmann
Daniel
AxMod 3D Print
Arksine
Tschipel