- Keeps the markdown inside the code blocks as is
- Logs the modified lines (mkdocs serve —verbose)
Signed-off-by: Damien Martin <damlobster@gmail.com>
This fixes the bug introduced by f1091a484b.
The problem is that condition was returning string which
could not be converted to boolean. We solve that by showing
`Start Printing` when `is_active`.
```
ERROR:root:Unhandled exception during run
Traceback (most recent call last):
...
File "/opt/klipper/klippy/extras/display/menu.py", line 117, in eval_enable
return bool(ast.literal_eval(self._enable_tpl.render(context)))
File "/usr/lib/python2.7/ast.py", line 49, in literal_eval
node_or_string = parse(node_or_string, mode='eval')
File "/usr/lib/python2.7/ast.py", line 37, in parse
return compile(source, filename, mode, PyCF_ONLY_AST)
File "<unknown>", line 1
/opt/octoprint/uploads/wait_print.gcode
```
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
whilst this line is in Measuring_Resonances.md, users following this guide for other reasons have no cause reason to read that and don't have an explanation for what they didn't know they didn't do.
Signed-off-by: Rowland Straylight <rowlandstraylight@gmail.com>
Created two new extended gcodes: Z_OFFSET_APPLY_ENDSTOP, and Z_OFFSET_APPLY_PROBE.
These use the z gcode offset to revise the probe offset, or z endstop position
allowing users to make a frequently used babystepping value permanent without
manual config editing.
Signed-off-by: Ben Eastep <shifting@shifting.ca>
A higher UART baud rate will allow for faster transfers and may result
in more stable operation in general. Increase the baud to 40000 on
32bit MCUs and leave the baud at 9000 baud for 8bit AVR MCUs.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It looks like the tmc2209 chips have increased uart errors with the
default SENDDELAY of zero. Increasing the SENDDELAY to two seems to
work around this issue.
Reported by @ReXT3D.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Updates firmware validation to use a dictionary if provided (or found
when updating from the default out/ directory).
Validation without a dictionary still checks the following (in order):
1. Active firmware's raw dictionary changed after update
2. Checksum of firmware.cur matches expected
Signed-off-by: Justin Schuh <code@justinschuh.com>
Validation passes if either of the following succeeds (in order):
1. Active firmware's raw dictionary changed after update
2. Checksum of firmware.cur matches expected
Additionally, deletes firmware.bin if found after update succeeds.
Signed-off-by: Justin Schuh <code@justinschuh.com>
The M300 example macro now sets the PWM cycle time to generate the requested
frequency. 'scale' did not have the desired effect. Duty cycle is now
fixed at 0.5. All S parameter values less than 1 generate a 1Hz 'tone'
to avoid division-by-zero.
Signed-off-by: Stefan Holst <mail@s-holst.de>
Document change in behavior of the controller_fan module.
Lookup heater objects in connect() event handler.
Return list of stepper names from stepper_enable.get_steppers().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allows contoller_fan sections to monitor only certain steppers instead of
all of them, similar to how heaters are currently handled.
Signed-off-by: Sophie Hirn <sophie.hirn@wyvernscale.com>
This config was a community effort and was author and tested by sihawken, 3D.Subzwari & dapostol73.
Signed-off-by: Demetrius Apostolopoulos <dapostol73@hotmail.com>
The Eryone ER-20 is a STM32F103 based 3D printer which ships with a 16KiB bootloader. Their official version of Marlin starts at 0x08004000.
Signed-off-by: Simon Hawkenson <simon@hawkenson.ca>
This implements SPI for the rp2040 target. All output groupings of both
SPI blocks are available for use.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Set the reqclock on trsync commands to ensure those commands do not
cause 32-bit timer rollover errors. Otherwise, it may result in
"Timer too close" errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This implements hardware PWM support for the rp2040. The maximum
value(100% duty) is set to 255 to match the other controllers. Cycle
time is clamped automatically, and uses the full 8.4 fractional range of
the rp2040 PWM block. This allows a maximum PWM frequency of 490kHz and
a minimum frequency of 1915 Hz.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Information and some lines verbatim were sourced from the official BigTreeTech Octopus
GitHub repository to make this configuration as well as existing configurations in the same
folder as this one
Signed-off-by: Charles Pickering <charles.pickering@live.com>
The rp2040 doesn't have a chip ID, but the flash chip connected does. We
can get this ID by asking the flash chip directly, but doing so requires
disengaging the XIP layer, performing the interrogation of the flash
chip, and then re-enabling the XIP layer. This gives us a 64-bit unique
ID that we can use as our USB serial number.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
In binutils 2.36 and above the -nostartfiles option is no longer
ignored. -nostartfiles is actually a gcc option, and so isn't supported
by ld. Earlier versions of binutils however had less error checking, and
thus just ignored the option.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Support the rp2040 (as tested on a Raspberry Pi Pico board). This
adds basic uart, timer, gpio, and watchdog support.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use CONFIG_MACH_AVR instead of CONFIG_CLOCK_FREQ to check for slow
mcus. Some fast MCUs do not export a high clock frequency.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Do not infer the sercom from the config section name, as that
prevents one from using SPI buses on multiple samd mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Damien Martin
Kamil Trzcinski
strayr
shiftingtech
Justin Schuh
Daniel Da Cunha
s-holst
Sophie Hirn
Demetrius Apostolopoulos
Simon Hawkenson
Lasse Dalegaard
Martin
Henky Prayoga
charlespick
Dmitry Butyugin