For example, Raspbian GNU/Linux 8 (jessie) uses an old GCC version 4.9.2
which uses -std=gnu90 by default.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Changing this check from debugoutput to debuginput allows remote applications to perform tests against Klippy without an MCU connected.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Input shaping can help to reduce printer vibrations due to resonances
and eliminate or reduce ghosting in prints.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Register API endpoints for "pause_resume/pause", "pause_resume/resume" and "pause_resume/cancel".
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
If a shutdown occurs during a PID_CALIBRATE command (eg, due to a
heater problem) then exit cleanly instead of throwing an internal
error.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change write_graphics() from taking one pixel row of n characters to
taking all the rows and columns for one character cell.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit allows to modify the icons (or glyphs) in the displays that
support it. Existing icons can be modified and new icons can be added via
a [display_glyph] section in the config.
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Rework extruder.get_trapq() into extruder.sync_stepper() so that
extruder_stepper.py does not need to directly access the extruder
internals.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Option for using the current diameter instead of nominal while the first measurement isn't in place
Signed-off-by: Matthias Pabel <matthias.pabel@hs-augsburg.de>
This reverts commit 43fa41c1af.
The above commit disabled absolute extrude moves because it was
unclear if the code would work properly when an M221 extrude factor or
G92 offset was in use. However, since the calculation is done
relative to the raw E position and is sent as a raw E position to
gcode.cmd_G1() these modes should not matter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If self.kin_flush_delay changes after a G4 dwell command (or other
non-kinematic time update) then it could lead to "internal step
compression" errors. Make sure to handle this case in
flush_step_generation().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make it clear that gcode.get_status() to be called without an
eventtime by defaulting eventtime=None.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store a reference to the gcode class in self.code. Obtain the
z_offset once and use for both the oldval and newval calculation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 9530373c introduced a minimum value of zero for the g-code z
position. Unfortunately, that would likely cause the tuning tower to
not emit a command at the start of a test because the initial dummy z
position is set to a negative value. The minimum bound should not be
needed so remove it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This gives it parity with heater_fan. Also change the default speed from
max_power to 1.0, since it is already scaled by max_power in set_speed.
Signed-off-by: Adrian Keet <arkeet@gmail.com>
Commit c3899cef inadvertently broke the error check for unused config
options. Add a new note_valid parameter to the config access wrappers
and use that in get_status() to fix the check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
round to only 6 decimal places of precision. prevents doing extra retry
from small variations due to floating point math.
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
Always disable the PWM after each command sent. Automatically trim
the command duration so the PWM disable doesn't increase the total
pulse time (when the duration is 200ms or greater).
Track the ideal command end time separately from the pwm transmit time
and only delay toolhead moves to this ideal time.
Update verify_state() to automatically schedule the check using the
time of the last sent command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename try_load_module() so that it uses consistent naming for
"printer objects". Change the function to raise an error by default
if the specified module does not exist.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove the parsing helpers from the main gcode class now that all
callers have been converted to use the parsing helpers in the
GCodeCommand class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of passing a dictionary to the command handlers, create a
wrapper class and pass that class to the command handlers. This can
simplify the command handler code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Avoid using doubles as flags when generating steps during "lead up to
stepper activity". Instead, explicitly track how many inactive move
entries are skipped and only generate steps for those entries.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't assume the times passed to itersolve_gen_steps_range() are
contained within the move. It's possible the checks in
itersolve_generate_steps() may round to different values when
converting the times to a relative move time.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The beagleboard TI kernel 4.14 and 4.19 contain a commit which change
the device names ("pwm: Create device class for pwm channels") from
pwmN to pwm-${chip}:N. This commit was never merged into the upstream
kernel.
Decrease the number of pwm channels to a more reasonable 16. Increase
the number of pwm chips to 8 since the replicape servo pwm outputs are
on pwmchip4.
Update replicape code to detect appropriate channel.
Signed-off-by: Janne Grunau <janne-gh@jannau.net>
Add a 50ms delay from the initial clock measurement to the first
get_clock query. Disable the prediction_variance filter on each
get_clock query so that none of those measurements are ignored.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The heater logic is an independent module that does not need to be
treated as part of the "core" klipper code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's no longer necessary to queue gcode scripts - gcode.run_script()
now does that automatically.
Also, make release_gcode config optional.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The probe_finalize() name is used for callbacks in both the
PrinterProbe and ProbePointsHelper classes. Rename the PrinterProbe
callback to avoid confusion.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the method to make it more clear that it is a low-level call
that should be rarely used.
Also, change gcode_button.py, hall_filament_width_sensor.py, and
tsl1401cl_filament_width_sensor.py to use respond_info() instead of
respond_raw().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Report low-level disk errors via the log and use the normal sdcard
mechanism to report end of sdcard print to gcode users.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's important to raise an error (instead of calling respond_error() )
so that a G20 will stop a virtual_sdcard print.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No need to check for '#original' in params - it's always there.
Properly handle a lower case m118 command. Don't register a help text
for the legacy M118 g-code command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Raising an error (instead of reporting an error) is important as only
a raised error will stop a print from virtual_sdcard.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 402110f6 didn't actually fix absolute extrude mode. For now,
report an error if an extrude move is requested in absolute extrude
mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fix linear_travel optimization. Use "2*pi" instead of "radians(360)".
Always emit at least one segment and always end at the final target
coordinates.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fix Z moves so that the movement is spaced out among the arc movements.
Fix extrude moves when in absolute extrude mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the normal gcode.get_float() mechanism for extracting parameters
from the g-code command.
Don't register descriptions for the G2/G3 commands as the convention
is to only use descriptions for "extended g-code commands".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This reverts commit 5c8d15bbee.
The lower_probe() code was already manually optimizing the timing of
the pwm disable, and that conflicted with the optimization in commit
5c8d15bb.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fysetc Cheetah v1.2 boards require a special sequence to reset reliably.
This sequence works for me in all cases. Simpler sequences without
double reset did not work correctly. This is likely because of a weird
stateful circuitry for toggling the bootloader state.
Cheetah boards use RTS to configure bootloader triggering. By default,
pySerial sets RTS on connect, which unfortunately configures the board
to start the bootloader on reset.
Add a toggle for the RTS state to allow users to workaround. The RTS state
is set before the serial connection is opened, so there are no glitches.
Addresses #2026.
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Some clones don't raise the pin on a reset and the ANTClabs BL-Touch
sometimes doesn't raise the pin either.
Rework the (infrequently called) sensor test code to always issue a
pin_up command before the touch command. Also, perform a reset and
retry if the sensor test fails.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Be sure to fully raise the probe prior to starting any future toolhead
movements in the multi_probe_end() case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If an error is found during the pin_up_not_triggered check, then apply
the reset command for a full second (instead of just 100ms). This
gives the bltouch more time to check its internal state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Return the triggered state from verify_state() and update the callers
to raise the error (if needed).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some stepper motor drivers do not respond well to rapid "step +
direction change + step" events. In particular, it is believed this
can cause "over current" events on the tmc2208 drivers when they are
in "stealthchop" mode. Detect these events and remove them from the
generated step times.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is likely only developers will be interested in testing the menu
system, so no need to have it in the default menu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Disable support for customizing the main lcd display content via the
menu system. Advise users to use the new display_data config sections
as a replacement.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a new config based system for specifying the on-screen
contents of an lcd screen. The default screen configuration (found in
klippy/extras/display/display.cfg) is the same as the previous
hard-coded display, so this should not change behavior for existing
users.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some stepper motor drivers do not respond well to rapid "step +
direction change + step" events. In particular, it is believed this
can cause "over current" events on the tmc2208 drivers when they are
in "stealthchop" mode. Detect these events and remove them from the
generated step times.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the stepper changes direction then the average velocity since the
last step pulse isn't a good indicator of the next step pulse.
Instead, reset the bounds checking to use a low starting guess.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The queue_append system predates the iterative solver - it was useful
when many different kinematic functions directly added steps to the
step compression queues. With the iterative solver being the only
source of step generation, it is simpler to directly add steps from
the iterative solver code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use new mcu.lookup_query_command() for all commands that query
information from the micro-controller.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Convert standard queries to use the acknowledgments of the sent
command to determine if the response was received or not. This also
controls command retransmissions (should the response have been lost).
The tmc_uart.py will continue to use the old mechanism as the tmcuart
responses are not sent synchronously with the query command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add ability for the host code to get a notification when the ack for a
command sent to the micro-controller is received. This is in
preparation for improved detection of message loss between mcu and
host.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's not valid to set the TPWMTHRS in a "klippy:connect" event handler
because the TMCVirtualPinHelper and TMCCommandHelper classes were
expecting that field to be set during the config reading phase.
Revert "tmc: Fix typo preventing stealthchop threshold from being set"
This reverts commit 7d76067ff9.
Revert "tmc: Query the stepper step_distance from the stepper object"
This reverts commit 67b2852249.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Arksine
Dmitry Butyugin
Denis Ignatenko
Florian Heilmann
theophile
matpab
Adrian Keet
Rubens Panfili
fess
Nathan Plamondon
Lucio Tarantino
Janne Grunau
Piotr Usewicz
Grigori Goronzy
David Smith
Jeremy Briffaut
kakou-fr
FanDjango