Default to running dfu-util via sudo as most machines will not have
the user setup with permissions to access the raw usb device.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The z_adjust offset provided to adjust_steppers is calculated given the
steppers adjust exactly according to the given x_adjust/y_adjust. As the
algorithm eliminates an offset that is common to all steppers, this offset
must be taken into account in the final correction.
Signed-off-by: Arne Jansen <arne@die-jansens.de>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for entering the "stm32duino" bootloader via the arduino
1200 baud USB request. Add supprot for flashing over USB via the
"make flash" command.
Rename the existing "make flash" command to "make serialflash".
Default to using a bootloader in Kconfig.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a script to help flash Klipper over USB. This tool can instruct
Klipper to enter into bootloader mode and it can help track changes in
device name during that transition.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The z_offset calculation should have been calculated from the probe
height to the measured bed position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the field names from the trinamic specification. This makes the
field similar to all the other driver_XXX config options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
sense_resistor is now a mandatory parameter for tmc2660 blocks. Duet2 users should use a value of 0.051
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Don't immediately raise an error if the heating_gain check fails.
Instead, just transition to the normal max_error check. This should
make the code less likely to raise an error should the heater have a
slow approach to the target temperature.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow the first check_gain_time interval to only require a
heating_gain relative to the lowest observed temperature during that
interval. This makes the code less likely to raise a spurious error
when the heater is enabled while the heater temperature is dropping.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't reset the error counter if the reported temperature is
significantly above the target temperature. This may help catch cases
where the temperature sensor reports random values.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Using the Duet2 config as a base for your own config will no longer turn
on all heaters and fans at full power during the (almost inevitable) MCU
shutdown that will occur during initial Klipper setup.
Signed-off-by: Benoit Miller <github@benoitmiller.ca>
It's rare to use all of a target's prerequisites in a recipe - replace
most cases with $< (the target's first prerequisite).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit e18501d0 broke the build for targets that added objects to
klipper.elf via adding dependencies. Rework the build so that it is
possible to add objects to klipper.elf via a new OBJS_klipper.elf
makefile variable.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some of the samd21 chips have limited memory - change the code to
reduce the size of global variables.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use a local linker script instead of the linker script provided by
Atmel. This will allow Klipper to use dynamic memory allocation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't use the list of dependencies in the klipper.elf build. This
allows the arch makefiles to add separate dependencies to klipper.elf.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This implementation includes a BaseSensor class that all underlying sensor implementations should subclass.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Kevin O'Connor
Arne Jansen
amblidex
Rui Caridade
Florian Heilmann
Voron
Benoit Miller
Arksine