The recommended TOFF time in "standalone mode" according to the
tmc2130 is 4, so use that as the default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the fan's max power is limited by the config, then scale speed
requests between 0 and max_power. This makes more sense for typical
g-code fan speeds.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the probe_z_offset parameter from delta_calibrate and
bed_tilt_calibrate to a z_offset parameter within the probe config
section. It's easier to understand the z offset setting when it is in
the probe config section.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the digital_output, pwm_output, and static_pwm_output config
sections to output_pin and move to a new module in the extras/
directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a heater falls out of the target range, accumulate the temperature
differences to determine if an error should be raised. This should
make it less likely to report an error for heaters that drift slightly
out of range, and it should make error reporting faster for heaters
that rapidly fall out of range.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
A default of 4 degrees and 10 seconds may be too aggressive - change
the default to 10 degrees and 15 seconds.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for additional carriages on cartesian printers. This is
used by some printers to handle multiple extruders.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for displaying basic status information on ST7920 and
HD44780 based LCDs that are attached directly to a micro-controller.
Signed-off-by: Marcio Teixeira <marcio@alephobjects.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the description of stepper phase adjusted endstops to a new
section in config-extra.cfg. This keeps the main example config file
a little more concise.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for directly printing from a local file on the host. This
may be useful if the host cpu is not fast enough to run OctoPrint
well.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Specify hardware pwm cycle times using the same method as software pwm
(in seconds, not clock ticks). Allow the fan code to be configured
with an explicit cycle time even when using software pwm.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for disabling homing checks via the homing_override
mechanism. This may be useful to move an axis prior to homing it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create a virtual pin that may be used as the z endstop pin on
cartesian printers that use the probe in place of a z endstop.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow a set of g-code scripts to be run on each probe invocation.
This may be useful for probes that need to be setup before they are
useful (eg, with servo actuated probes).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow users to override the behavior of G28 using a new
"homing_override" config section. This may be used on printers that
require specific steps during the homing process.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add the ability to alias multiple output pins from a single pin alias.
This makes it possible to support some cases where a single logical
output is driven by multiple output pins.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add the ability to define output pins that may be set at runtime with
a new SET_PIN extended g-code command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow multiple steppers to be defined for a single cartesian axis.
This adds support for dual-z setups.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for configuring and controlling the hardware specific to
the revision "B3" Replicape board.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add initial support for controlling multiple independent
micro-controllers from a single Klippy host instance. Add basic
support for synchronizing the clocks of the additional mcus to the
main mcu's clock.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support an "ad5206" config section so that one can configure the
digipots found on Reprap "RAMBo" boards.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow digital and PWM output pins to be setup via new config
sections. This makes it easier to setup pin configurations.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Douglas Hammond
Michael Barbour