mirror of https://github.com/Desuuuu/klipper.git
tmc2130: Add initial support for TMC2130 stepper motor drivers
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
61fbd193f9
commit
680c92de40
|
@ -402,6 +402,44 @@
|
|||
# default is to not scale the 'channel_x' parameters.
|
||||
|
||||
|
||||
# Configure a TMC2130 stepper motor driver (one may define any number
|
||||
# of sections with a "tmc2130" prefix).
|
||||
#[tmc2130 my_name]
|
||||
#cs_pin:
|
||||
# The pin corresponding to the TMC2130 chip select line. This pin
|
||||
# will be set to low at the start of SPI messages and raised to high
|
||||
# after the message completes. This parameter must be provided.
|
||||
#microsteps:
|
||||
# The number of microsteps to configure the driver to use. Valid
|
||||
# values are 1, 2, 4, 8, 16, 32, 64, 128, 256. This parameter must
|
||||
# be provided.
|
||||
#interpolate: True
|
||||
# If true, enable TMC2130 step interpolation (the driver will
|
||||
# interally step at a rate of 256 micro-steps). The default is True.
|
||||
#run_current:
|
||||
# The amount of current (in amps) to configure the driver to use
|
||||
# during stepper movement. This parameter must be provided.
|
||||
#hold_current:
|
||||
# The amount of current (in amps) to configure the driver to use
|
||||
# when the stepper is not moving. The default is to use the same
|
||||
# value as run_current.
|
||||
#sense_resistor: 0.110
|
||||
# The resistance (in ohms) of the motor sense resistor. The default
|
||||
# is 0.110 ohms.
|
||||
#stealthchop: False
|
||||
# Enable "stealthChop" mode. The default is False.
|
||||
#driver_IHOLDDELAY: 8
|
||||
#driver_TPOWERDOWN: 0
|
||||
#driver_BLANK_TIME_SELECT: 1
|
||||
#driver_TOFF: 1
|
||||
#driver_HEND: 7
|
||||
#driver_HSTRT: 0
|
||||
# Set the given register during the configuration of the TMC2130
|
||||
# chip. This may be used to set custom motor parameters. The
|
||||
# defaults for each parameter are next to the parameter name in the
|
||||
# above list.
|
||||
|
||||
|
||||
# Homing override. One may use this mechanism to run a series of
|
||||
# g-code commands in place of a G28 found in the normal g-code input.
|
||||
# This may be useful on printers that require a specific procedure to
|
||||
|
|
|
@ -0,0 +1,70 @@
|
|||
# TMC2130 configuration
|
||||
#
|
||||
# Copyright (C) 2018 Kevin O'Connor <kevin@koconnor.net>
|
||||
#
|
||||
# This file may be distributed under the terms of the GNU GPLv3 license.
|
||||
import math
|
||||
|
||||
class tmc2130:
|
||||
def __init__(self, config):
|
||||
printer = config.get_printer()
|
||||
# pin setup
|
||||
ppins = printer.lookup_object("pins")
|
||||
cs_pin = config.get('cs_pin')
|
||||
cs_pin_params = ppins.lookup_pin('digital_out', cs_pin)
|
||||
if cs_pin_params['invert']:
|
||||
raise pins.error("tmc2130 can not invert pin")
|
||||
self.mcu = cs_pin_params['chip']
|
||||
pin = cs_pin_params['pin']
|
||||
self.oid = self.mcu.create_oid()
|
||||
self.mcu.add_config_cmd(
|
||||
"config_spi oid=%d bus=%d pin=%s mode=%d rate=%d shutdown_msg=" % (
|
||||
self.oid, 0, cs_pin_params['pin'], 3, 3600000))
|
||||
run_current = config.getfloat('run_current', above=0., maxval=2.)
|
||||
hold_current = config.getfloat('hold_current', run_current,
|
||||
above=0., maxval=2.)
|
||||
sense_resistor = config.getfloat('sense_resistor', 0.110, above=0.)
|
||||
steps = {'256': 0, '128': 1, '64': 2, '32': 3, '16': 4,
|
||||
'8': 5, '4': 6, '2': 7, '1': 8}
|
||||
microsteps = config.getchoice('microsteps', steps)
|
||||
interpolate = config.getboolean('interpolate', True)
|
||||
stealthchop = config.getboolean('stealthchop', False)
|
||||
iholddelay = config.getint('driver_IHOLDDELAY', 8, minval=0, maxval=15)
|
||||
tpowerdown = config.getint('driver_TPOWERDOWN', 0, minval=0, maxval=255)
|
||||
blank_time_select = config.getint('driver_BLANK_TIME_SELECT', 1,
|
||||
minval=0, maxval=3)
|
||||
toff = config.getint('driver_TOFF', 1, minval=1, maxval=15)
|
||||
hend = config.getint('driver_HEND', 7, minval=0, maxval=15)
|
||||
hstrt = config.getint('driver_HSTRT', 0, minval=0, maxval=7)
|
||||
# calculate current
|
||||
vsense = False
|
||||
irun = self.current_bits(run_current, sense_resistor, vsense)
|
||||
ihold = self.current_bits(hold_current, sense_resistor, vsense)
|
||||
if irun < 16 and ihold < 16:
|
||||
vsense = True
|
||||
irun = self.current_bits(run_current, sense_resistor, vsense)
|
||||
ihold = self.current_bits(hold_current, sense_resistor, vsense)
|
||||
# configure GCONF
|
||||
self.add_config_cmd(0x00, stealthchop << 2)
|
||||
# configure CHOPCONF
|
||||
self.add_config_cmd(
|
||||
0x6c, toff | (hstrt << 4) | (hend << 7) | (blank_time_select << 15)
|
||||
| (vsense << 17) | (microsteps << 24) | (interpolate << 28))
|
||||
# configure IHOLD_IRUN
|
||||
self.add_config_cmd(0x10, ihold | (irun << 8) | (iholddelay << 16))
|
||||
# configure TPOWERDOWN
|
||||
self.add_config_cmd(0x11, tpowerdown)
|
||||
def add_config_cmd(self, addr, val):
|
||||
self.mcu.add_config_cmd("spi_send oid=%d data=%02x%08x" % (
|
||||
self.oid, (addr | 0x80) & 0xff, val & 0xffffffff), is_init=True)
|
||||
def current_bits(self, current, sense_resistor, vsense_on):
|
||||
sense_resistor += 0.020
|
||||
vsense = 0.32
|
||||
if vsense_on:
|
||||
vsense = 0.18
|
||||
cs = int(32. * current * sense_resistor * math.sqrt(2.) / vsense
|
||||
- 1. + .5)
|
||||
return max(0, min(31, cs))
|
||||
|
||||
def load_config_prefix(config):
|
||||
return tmc2130(config)
|
Loading…
Reference in New Issue