Allow the start value to be different from the default/shutdown value
for the pin. This will be useful for "heater fans" that should
startup in the off state, and transition to full on in a shutdown
state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Pass the sample_ticks and sample_count parameters directly in the
end_stop_home command instead. This simplifies the code.
Also, simplify calculation of next wakeup time in
end_stop_oversample_event().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Place a small notch on one side of the square. The notch provides
interesting information on the extruder performance, and it makes it
easier to compare with previous prints of the object.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Several items were recently implemented. Remove the "cubic vs
quadratic" item as investigations into cubic compression weren't
promising.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for configuring and controlling the hardware specific to
the revision "B3" Replicape board.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement the conversion from print_time to the local mcu's clock
within the C code. This simplifies the python code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Extend the look-ahead mechanism to work between moves that contain Z
movement. This improves Klipper's handling of g-code produced in
"vase mode".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It should no longer be necessary to configure "custom" commands during
mcu setup. The ad5206 and static_digital_output config sections
should provide similar functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Compile the PRU binary with -Os optimization, but request that the
timer dispatch code be compiled with -O2 optimization. This improves
the performance of timers slightly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The gcc -Os option significantly reduces the size of the PRU binary
and it has little impact on performance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is not necessary to limit stepper acceleration - only the limiting
of stepper torque is important.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a CONFIG_SIMULAVR option to the Kbuild menus and don't directly
prompt users for CONFIG_WATCHDOG or CONFIG_SERIAL_BAUD_U2X. The only
reason to disable these options would be if one were running on
simulavr. This simplifies the user visible menu options.
Also, only show CONFIG_CLEAR_PRESCALER for at90usb1286 chips.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of assuming the maximum PWM value is 255, export a constant
from the firmware to the host with the maximum value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Those that reach Klipper via github may jump directly to the docs/
directory in search of documentation. Add README.md and rework
Overview.md with that in mind.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The term "firmware" is ambiguous - it could refer to the entire
project (host and micro-controller software) or to just the
micro-controller software. Avoid the term in the documentation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Klipper software has progressed to the point where it does not
need to be described as "experimental" software.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Detect avr gcc v4.8.1 and then disable warnings during the klipper.o
linking to suppress bogus "misspelled signal handler" warnings.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a system startup script so that Klipper can automatically start at
boot time. Create an installation script that will install the system
dependencies and the startup script.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No need to recommend users disable "SD card support" in octoprint -
instead, just ignore the M21 command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Direct readers to the main Installation file to setup the python
virtual environment and remove the outdated instructions in the
Debugging file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename sched_timer_kick() to sched_timer_dispatch() and move its loop
into its callers in the board code. This eliminates the need to
export timer_try_set_next() from the board code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some additional tweeks to the scheduler has resulted in minor
improvements to the stepper benchmarks.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a TICKS() macro during config parsing that will translate
time in seconds to time in clock ticks.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the logic to calculate and report the stepper's current position
from endstop.c to stepper.c. This localizes the stepper code into
stepper.c.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add initial support for micro-controller resets via the Arduino reset
mechanism. Also, automatically attempt a firmware restart if the
printer CRC does not match.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow sendf() to be called from irq and timer context - check for the
case where sendf() is called while already in sendf() and simply
discard those messages. This makes it safe to use output() debugging
calls even in irq and timer context.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the default compression error window (max_error) from 50us to
25us - it's common for stepper motor drivers to have 30us for their
"pwm fixed off time" and it would be good for the steps to be
scheduled within that time.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a DECL_CONSTANT macro to allow the firmware to define constants
that are to be exported to the host during the "identify" phase. This
replaces the existing hardcoded mechanism of scanning the Kconfig
header file for certain constants.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use a more real-world example to improve the description of message
block contents. Make it more clear that the data dictionary contains
and utilizes the full command descriptions.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Various installation updates. Recommend upgrade to OctoPrint v1.3.0.
Recommend configuring OctoPrint to not disconnect on error. Note
quirk with needing to reload page if "/tmp/printer" not in list of
serial connections. Add brief documentation on use of extended
commands and checking for errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support human readable commands (eg, "help"). Add a "help" command to
list these extended commands.
Also, add support for declaring command aliases, command help, and
command availability next to the handlers themselves.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Check that all options specified in the config file are valid. This
catches possible typos and spelling errors in variable names that have
a default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of writing error messages to stderr, route them into the
python code and use the standard python logging system.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for greenlets - a mechanism for tasks that can pause while
still allowing regular reactor events to occur.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Should a homing move complete without hitting the endstop, then
disable motors, disable the endstop checking, and report the error to
the user.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Writing to the debug log can cause an unbounded delay due to disk IO.
This is particularly so on embedded machines such as the Raspberry Pi
that run on SD cards. These log writing delays can cause problems for
the main processing threads.
The new "queuelogger" code forwards all the main thread log messages
to a queue, and a background thread writes the log messages from the
queue to the destination file. This eliminates the IO delay from the
main threads.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Due to the lookahead, small changes in the direction of the toolhead
cause minor changes in toolhead velocity. These "cornering" velocity
changes cause the current extruder code to trigger pressure advance
and its associated pressure retract. This causes the extruder to
rapidly "jerk" the filament.
This code change updates the extruder to detect velocity changes due
solely to cornering and avoid pressure advance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some details on the code flow and organization have changed since
support for ARM processors was added. Update Code_Overview.md
accordingly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor