This config was not yet available - I have updated all the pin defines, starting with the BTT SKR board which is the most similar board + tested it on my printer which is currently working with the TMC5160 drivers using software SPI. I have not tested it with other drivers etc but the config should work for them.
Signed-off-by: Chester Lowrey <hilo90mhz@gmail.com>
Some stepper motor drivers do not respond well to rapid "step +
direction change + step" events. In particular, it is believed this
can cause "over current" events on the tmc2208 drivers when they are
in "stealthchop" mode. Detect these events and remove them from the
generated step times.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is likely only developers will be interested in testing the menu
system, so no need to have it in the default menu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Disable support for customizing the main lcd display content via the
menu system. Advise users to use the new display_data config sections
as a replacement.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a new config based system for specifying the on-screen
contents of an lcd screen. The default screen configuration (found in
klippy/extras/display/display.cfg) is the same as the previous
hard-coded display, so this should not change behavior for existing
users.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Correct TMC2130 diag1_pin logic - the diag1_pin logic should be inverted and pulled up.
Use pullup for endstops - pullups should be used here.
Signed-off-by: Wen-Jeng Hsiao <isuperwilly@gmail.com>
Explicitly disable the SysTick interrupt and explicitly set the stack
pointer, as some bootloaders aren't handling this correctly.
Signed-off-by: Chris Lombardi <clearchris@hotmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some stepper motor drivers do not respond well to rapid "step +
direction change + step" events. In particular, it is believed this
can cause "over current" events on the tmc2208 drivers when they are
in "stealthchop" mode. Detect these events and remove them from the
generated step times.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the stepper changes direction then the average velocity since the
last step pulse isn't a good indicator of the next step pulse.
Instead, reset the bounds checking to use a low starting guess.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The queue_append system predates the iterative solver - it was useful
when many different kinematic functions directly added steps to the
step compression queues. With the iterative solver being the only
source of step generation, it is simpler to directly add steps from
the iterative solver code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This reverts commit a2c309a2b0.
The above commit is causing crashes on the stm32f103xb chip when spi
is in use. It's unclear what the cause of the regression is, but the
optimization isn't required so revert it until the root cause can be
determined.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit bd6c25c9 introduced a typo that caused the clock divisors to
not be set correctly on stm32f1.
Reported by @brianrjones69.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update printer-seemecnc-rostock-max-v2-2015.cfg to include the [display] and [board_pins] sections needed for Reprap 20x4 LCD display (#2561).
Signed-off-by: Angelo Lagis <angelo_lagis@hotmail.com>
Use new mcu.lookup_query_command() for all commands that query
information from the micro-controller.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Convert standard queries to use the acknowledgments of the sent
command to determine if the response was received or not. This also
controls command retransmissions (should the response have been lost).
The tmc_uart.py will continue to use the old mechanism as the tmcuart
responses are not sent synchronously with the query command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
kakou-fr
Chester
Garth Snyder
Arksine
Willy Hsiao
clearchris
David Smith
Denis Ignatenko
Angelol125
FanDjango