Change the simulator to use the generic timer_irq.c and serial_irq.c
code for (dummy) timer and io handling. This is just to make the code
a better example for other developers (most micro-controllers will use
the timer_irq.c and serial_irq.c code).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Added printer-tronxy-x8-2018.cfg for the Tronxy X8 with the CXY-V2-0508 board.
Signed-off-by: Seyed Seraj <s.seraj@hotmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Switch the host code from the CLOCK_MONOTONIC clock to the Linux
specific CLOCK_MONOTONIC_RAW clock. It's common for ntp to slew the
CLOCK_MONOTONIC clock to account for drift, and that can break the
host's ability to make accurate predictions of the micro-controller
clock. This could lead to "move queue empty" errors. The
CLOCK_MONOTONIC_RAW clock is not slewed and thus should not have this
problem.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add M117 and M73 to the list of supported G-Codes.
Also, remove M117 from the list of commands reported by the HELP
command as that command is typically only used to list "extended
g-code" commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No need to include all the test preparation in the verbose output - as
that can make the output more confusing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The SPI interface needs to be enabled and configured to the correct
settings of a given oid before CS is asserted. The new function
spi_prepare() allows ports to do that.
This port only introduces the new function in all ports with no
implementation and adds the call to the Klipper generic firmware code.
That means everything still works as before. Ports need to be changed
to fix the underlying issue.
Discussion about the motivation here:
https://github.com/KevinOConnor/klipper/pull/453#issuecomment-403131149
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Add basic SPI support and associated documentation.
v2: remove baud rate check, fix baud rate calculations
v3: finish transaction with BSY check, disable SPI when not in use
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Add generic temperature smoothing to the Heater class. This is useful
to avoid min_extrude_temp and verify_heater errors due to measurement
noise.
Rename the pid_deriv_time config option to smooth_time so that the
smoothing amount need only be specified once.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Extend the ADC out of range check so that it is possible to sample
multiple times before going into a shutdown state. This reduces the
chance that measurement noise will cause an error. In an actual over
temperature (or under temperature event) it is expected that the
sensor will consistently report the problem, so extra checks for an
additional second or two should not substantially increase risk.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add mcu support for periodically polling for a button press. Add host
code support for registering buttons and invoking callbacks for them.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add the ability to register callbacks - both asynchronous (ie, from
another thread) and synchronous.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an ability to run a series of g-code commands from a reactor
callback that isn't part of the normal g-code command processing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Seyed Seraj
Grigori Goronzy
Eric Callahan
Hans Raaf
Janar Sööt