mirror of https://github.com/Desuuuu/klipper.git
config: Add Anycubic Kossel plus size delta printer config
Signed-off-by: Hans Raaf <hr-klipper@oderwat.de>
This commit is contained in:
parent
bae094eac3
commit
5b3444c060
|
@ -0,0 +1,107 @@
|
|||
# This file contains a configuration for the "Anycubic Kossel Linear
|
||||
# Plus Large Printing Size", "Anycubic Kossel Pulley Plus Large
|
||||
# Printing Size" and similar delta printer from 2017. The printer uses
|
||||
# the TriGorilla board which is an AVR ATmega2560 Arduino + RAMPS
|
||||
# compatible board. To use this config, the firmware should be
|
||||
# compiled for the AVR atmega2560.
|
||||
|
||||
# See the example.cfg file for a description of available parameters.
|
||||
|
||||
[stepper_a]
|
||||
arm_length: 271.50
|
||||
step_pin: ar54
|
||||
dir_pin: !ar55
|
||||
enable_pin: !ar38
|
||||
step_distance: .0125
|
||||
endstop_pin: ^ar2
|
||||
homing_speed: 60
|
||||
# The next parameter needs to be adjusted for
|
||||
# your printer. You may want to start with 280
|
||||
# and meassure the distance from nozzle to bed.
|
||||
# This value then needs to be added.
|
||||
position_endstop: 295.6
|
||||
angle: 90
|
||||
|
||||
[stepper_b]
|
||||
step_pin: ar60
|
||||
dir_pin: !ar61
|
||||
enable_pin: !ar56
|
||||
step_distance: .0125
|
||||
endstop_pin: ^ar15
|
||||
angle: 210
|
||||
|
||||
[stepper_c]
|
||||
step_pin: ar46
|
||||
dir_pin: !ar48
|
||||
enable_pin: !ar62
|
||||
step_distance: .0125
|
||||
endstop_pin: ^ar19
|
||||
angle: 330
|
||||
|
||||
[extruder]
|
||||
step_pin: ar26
|
||||
dir_pin: !ar28
|
||||
enable_pin: !ar24
|
||||
step_distance: 0.010989
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: ar10
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: analog13
|
||||
control: pid
|
||||
pid_Kp: 25.349
|
||||
pid_Ki: 1.216
|
||||
pid_Kd: 132.130
|
||||
min_extrude_temp: 150
|
||||
min_temp: 0
|
||||
max_temp: 275
|
||||
|
||||
#[heater_bed]
|
||||
#heater_pin: ar8
|
||||
#sensor_type: EPCOS 100K B57560G104F
|
||||
#sensor_pin: analog14
|
||||
#control: watermark
|
||||
#min_temp: 0
|
||||
#max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: ar9
|
||||
kick_start_time: 0.200
|
||||
|
||||
[heater_fan extruder_cooler_fan]
|
||||
pin: ar44
|
||||
|
||||
[mcu]
|
||||
serial: /dev/ttyUSB0
|
||||
pin_map: arduino
|
||||
|
||||
[printer]
|
||||
kinematics: delta
|
||||
max_velocity: 200
|
||||
max_accel: 3000
|
||||
max_z_velocity: 200
|
||||
motor_off_time: 360
|
||||
delta_radius: 115
|
||||
# if you want to DELTA_CALIBRATE you may need that
|
||||
#minimum_z_position: -5
|
||||
|
||||
#[delta_calibrate]
|
||||
#radius: 115
|
||||
#manual_probe:
|
||||
# If true, then DELTA_CALIBRATE will perform manual probing. If
|
||||
# false, then a PROBE command will be run at each probe
|
||||
# point. Manual probing is accomplished by manually jogging the Z
|
||||
# position of the print head at each probe point and then issuing a
|
||||
# NEXT extended g-code command to record the position at that
|
||||
# point. The default is false if a [probe] config section is present
|
||||
# and true otherwise.
|
||||
|
||||
# "RepRapDiscount 2004 Smart Controller" type displays
|
||||
[display]
|
||||
lcd_type: hd44780
|
||||
rs_pin: ar16
|
||||
e_pin: ar17
|
||||
d4_pin: ar23
|
||||
d5_pin: ar25
|
||||
d6_pin: ar27
|
||||
d7_pin: ar29
|
Loading…
Reference in New Issue