The M300 example macro now sets the PWM cycle time to generate the requested
frequency. 'scale' did not have the desired effect. Duty cycle is now
fixed at 0.5. All S parameter values less than 1 generate a 1Hz 'tone'
to avoid division-by-zero.
Signed-off-by: Stefan Holst <mail@s-holst.de>
Document change in behavior of the controller_fan module.
Lookup heater objects in connect() event handler.
Return list of stepper names from stepper_enable.get_steppers().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allows contoller_fan sections to monitor only certain steppers instead of
all of them, similar to how heaters are currently handled.
Signed-off-by: Sophie Hirn <sophie.hirn@wyvernscale.com>
This config was a community effort and was author and tested by sihawken, 3D.Subzwari & dapostol73.
Signed-off-by: Demetrius Apostolopoulos <dapostol73@hotmail.com>
The Eryone ER-20 is a STM32F103 based 3D printer which ships with a 16KiB bootloader. Their official version of Marlin starts at 0x08004000.
Signed-off-by: Simon Hawkenson <simon@hawkenson.ca>
This implements SPI for the rp2040 target. All output groupings of both
SPI blocks are available for use.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Set the reqclock on trsync commands to ensure those commands do not
cause 32-bit timer rollover errors. Otherwise, it may result in
"Timer too close" errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This implements hardware PWM support for the rp2040. The maximum
value(100% duty) is set to 255 to match the other controllers. Cycle
time is clamped automatically, and uses the full 8.4 fractional range of
the rp2040 PWM block. This allows a maximum PWM frequency of 490kHz and
a minimum frequency of 1915 Hz.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Information and some lines verbatim were sourced from the official BigTreeTech Octopus
GitHub repository to make this configuration as well as existing configurations in the same
folder as this one
Signed-off-by: Charles Pickering <charles.pickering@live.com>
The rp2040 doesn't have a chip ID, but the flash chip connected does. We
can get this ID by asking the flash chip directly, but doing so requires
disengaging the XIP layer, performing the interrogation of the flash
chip, and then re-enabling the XIP layer. This gives us a 64-bit unique
ID that we can use as our USB serial number.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
In binutils 2.36 and above the -nostartfiles option is no longer
ignored. -nostartfiles is actually a gcc option, and so isn't supported
by ld. Earlier versions of binutils however had less error checking, and
thus just ignored the option.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Support the rp2040 (as tested on a Raspberry Pi Pico board). This
adds basic uart, timer, gpio, and watchdog support.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use CONFIG_MACH_AVR instead of CONFIG_CLOCK_FREQ to check for slow
mcus. Some fast MCUs do not export a high clock frequency.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Do not infer the sercom from the config section name, as that
prevents one from using SPI buses on multiple samd mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* Add menuconfig option for stm32f072
* Add support for internal temp of stm32f072
* Share the temperature calculation logic between stm32f0x2 MCUs
Signed-off-by: Erik Henriksson <erikhenrikssn@gmail.com>
- Add dual_carriage abilities for hybrid-corexy and hybrid-corexz
- Introduce the module idex_mode
- Fix add_stepper to the correct rail in hybrid-corexy
Signed-off-by: Fabrice GALLET <tircown@gmail.com>
Daniel Da Cunha
s-holst
Kevin O'Connor
Sophie Hirn
Demetrius Apostolopoulos
Simon Hawkenson
Lasse Dalegaard
Martin
Henky Prayoga
charlespick
Dmitry Butyugin
shiftingtech
charlespick
henrikssn
Tircown
Joseph Orduna
squeekyzebra
github@matthewlloyd.net
Kamil Trzcinski
Eric Callahan