| .. |
|
__init__.py
|
klippy: Add support for dynamic loading of python modules
|
2018-01-28 12:19:26 -05:00 |
|
ad5206.py
|
spicmds: Rework SPI message transmission
|
2018-05-07 09:10:34 -04:00 |
|
adc_temperature.py
|
adc_temperature: Support defining custom sensors in the config file
|
2018-04-09 15:44:34 -04:00 |
|
bed_tilt.py
|
probe: Move code from bed_tilt and delta_calibrate into ProbePointsHelper
|
2018-05-20 11:41:07 -04:00 |
|
delta_calibrate.py
|
probe: Move code from bed_tilt and delta_calibrate into ProbePointsHelper
|
2018-05-20 11:41:07 -04:00 |
|
display.py
|
display: Round temperature and position to nearest whole number
|
2018-03-19 15:17:53 -04:00 |
|
fan.py
|
fan: Allow the fan shutdown_speed to be configured
|
2018-05-18 19:12:03 -04:00 |
|
heater_bed.py
|
heater: Add PrinterHeaters class that stores all sensors and heaters
|
2018-04-04 23:13:53 -04:00 |
|
heater_fan.py
|
fan: Allow the fan shutdown_speed to be configured
|
2018-05-18 19:12:03 -04:00 |
|
homing_override.py
|
gcode: Raise an error if a duplicate command is registered
|
2018-05-20 13:08:22 -04:00 |
|
multi_pin.py
|
pins: Remove module level get_printer_pins() and setup_pin() functions
|
2018-04-04 12:26:39 -04:00 |
|
output_pin.py
|
output_pin: Use new gcode.register_mux_command()
|
2018-05-20 12:44:02 -04:00 |
|
pid_calibrate.py
|
pid_calibrate: Make sure to unregister new control class on error
|
2018-04-06 11:39:24 -04:00 |
|
probe.py
|
z_tilt: Add support for Z_TILT_ADJUST
|
2018-05-22 22:23:44 -04:00 |
|
replicape.py
|
linux: Convert linux SPI code to use the generic spicmds.c code
|
2018-05-07 09:10:34 -04:00 |
|
servo.py
|
servo: Use new gcode.register_mux_command()
|
2018-05-20 12:40:10 -04:00 |
|
static_digital_output.py
|
static_digital_output: Add static_digital_output section to extras/
|
2018-03-17 13:06:51 -04:00 |
|
temperature_fan.py
|
temperature_fan: Don't write "temperature_fan " to prefix stats
|
2018-05-23 18:22:02 -04:00 |
|
thermistor.py
|
thermistor: Add Honeywell 100K and MGB18 thermistor definitions
|
2018-04-30 16:08:17 -04:00 |
|
tmc2130.py
|
tmc2130: Add initial support for TMC2130 stepper motor drivers
|
2018-05-20 18:03:06 -04:00 |
|
verify_heater.py
|
heater: Add PrinterHeaters class that stores all sensors and heaters
|
2018-04-04 23:13:53 -04:00 |
|
virtual_sdcard.py
|
gcode: Raise an error if a duplicate command is registered
|
2018-05-20 13:08:22 -04:00 |
|
z_tilt.py
|
z_tilt: Add support for Z_TILT_ADJUST
|
2018-05-22 22:23:44 -04:00 |
d7b29eca47