klipper-dgus/config
Matt Baker f2fbe98454 bed_mesh: enable relative offset bed meshes (#1323)
Adds parameter for bed meshes to be adjusted relative to a probed point
during calibration. This allows the probe z offset to be ignored for
probes that are not stable over time (for example, the thermal drift of
inductive probes). An endstop other than the probe is then necessary to
determine the bed-nozzle offset.

Signed-off-by: Matt Baker <baker.matt.j@gmail.com>
2019-03-21 10:39:22 -04:00
..
avrsim.cfg config: Update avrsim.cfg to use unique pins 2018-01-12 16:44:21 -05:00
example-corexy.cfg config: Use .0025 as the default z step_distance in sample configs 2018-02-25 16:00:55 -05:00
example-delta.cfg screws_tilt_adjust: Add new screws_tilt_adjust tool (#1367) 2019-03-08 11:47:17 -05:00
example-extras.cfg bed_mesh: enable relative offset bed meshes (#1323) 2019-03-21 10:39:22 -04:00
example-menu.cfg menu: enhancements 2019-01-07 21:39:50 -05:00
example-multi-mcu.cfg docs: Update documentation to note use of /dev/serial/by-path/ 2018-06-01 17:22:03 -04:00
example-polar.cfg polar: Experimental support for polar kinematics 2018-12-24 11:38:59 -05:00
example-winch.cfg winch: Add experimental support for cable winch kinematics 2018-12-24 11:38:59 -05:00
example.cfg pins: Document support for '~' to enable pull-down resistors 2019-03-17 21:07:31 -04:00
generic-azteeg-x5-mini-v3.cfg lpc176x: Add support for flashing via "make flash" 2019-03-08 22:22:41 -05:00
generic-bigtreetech-skr-v1.1.cfg config: Update generic-bigtreetech-skr-v1.1 (#1209) 2019-02-07 18:16:07 -05:00
generic-cramps.cfg pru: Disable ADC reading directly from the PRU 2018-06-27 12:10:25 -04:00
generic-duet2.cfg tmc2660: Use helper functions for register access and simplify TMC2660 parameters 2019-03-08 11:04:14 -05:00
generic-einsy-rambo.cfg tmc2130: Initial support for sensorless homing 2018-05-25 11:38:23 -04:00
generic-fysetc-f6.cfg config: Update generic-fysetc-f6.cfg display section 2019-02-07 18:23:17 -05:00
generic-gt2560.cfg config: Added example config file for Geeetech gt2560 controller. 2019-01-28 11:20:01 -05:00
generic-melzi.cfg config: Use consistent advice on flashing the Melzi board 2018-11-13 14:32:52 -05:00
generic-mini-rambo.cfg config: Use fastest PWM time in mini-rambo PWM DAC config 2018-09-11 09:40:48 -04:00
generic-minitronics1.cfg config: Add a generic-minitronics1.cfg example config file 2018-12-20 11:09:20 -05:00
generic-printrboard.cfg config: Reduce the stepper current in the example printrboard config 2019-03-14 10:44:02 -04:00
generic-radds.cfg config: Added encoder pins to radds example config 2019-01-02 17:46:06 -05:00
generic-rambo.cfg config: Fix hd44780 typo in rambo and ramps example configs 2018-03-06 13:15:09 -05:00
generic-ramps.cfg config: pin mapping for ender 3 stock display and encoder on ramps (#1075) 2019-01-06 11:51:27 -05:00
generic-re-arm.cfg lpc176x: Add support for flashing via "make flash" 2019-03-08 22:22:41 -05:00
generic-replicape.cfg replicape: Add config controls for the servo[01]_enable lines 2018-03-17 12:55:48 -04:00
generic-rumba.cfg config: Update extra extruder pins in generic-rumba.cfg 2019-03-14 11:48:25 -04:00
generic-smoothieboard.cfg lpc176x: Add support for flashing via "make flash" 2019-03-08 22:22:41 -05:00
kit-voron2-250mm.cfg config: Example config file for a stock 250mm build VORON2 printer 2019-02-13 12:07:20 -05:00
printer-adimlab-2018.cfg config: ADIMlab Add support for LCD knob and caselight 2018-10-19 11:10:32 -04:00
printer-anet-a8-2017.cfg config: add display support for Anet A8 2018-04-09 16:24:14 -04:00
printer-anet-e10-2018.cfg config: anet e10 update 2018-06-19 11:36:52 -04:00
printer-anycubic-i3-mega-2017.cfg config: Add a "printer-" prefix to example printer config files 2018-02-11 14:58:48 -05:00
printer-anycubic-kossel-2016.cfg config: Make the Anycubic delta configurations as similar as possible 2018-11-25 17:14:16 -05:00
printer-anycubic-kossel-plus-2017.cfg config: Make the Anycubic delta configurations as similar as possible 2018-11-25 17:14:16 -05:00
printer-creality-cr10-2017.cfg config: Use "ATC Semitec 104GT-2" for CR10 (and similar) heater beds 2019-02-08 12:20:16 -05:00
printer-creality-cr10mini-2017.cfg config: Use "ATC Semitec 104GT-2" for CR10 (and similar) heater beds 2019-02-08 12:20:16 -05:00
printer-creality-cr10s-2017.cfg config: Use "ATC Semitec 104GT-2" for CR10 (and similar) heater beds 2019-02-08 12:20:16 -05:00
printer-creality-cr20-2018.cfg config: Fix CR-20 click pin polarity 2018-12-15 18:38:03 -05:00
printer-creality-ender2-2017.cfg config: Use consistent advice on flashing the Melzi board 2018-11-13 14:32:52 -05:00
printer-creality-ender3-2018.cfg config: Update printer-creality-ender3-2018.cfg (#959) 2018-12-05 16:43:14 -05:00
printer-lulzbot-taz6-2017.cfg display: Add initial support for LCD screens attached to an MCU 2018-03-06 11:30:46 -05:00
printer-makergear-m2-2012.cfg endstop_phase: Move endstop phase homing code to new "extras" module 2018-10-16 13:09:23 -04:00
printer-micromake-d1-2016.cfg config: Add printer-micromake-d1-2016.cfg example config file 2018-12-18 20:59:43 -05:00
printer-seemecnc-rostock-max-v2-2015.cfg config: Add a "printer-" prefix to example printer config files 2018-02-11 14:58:48 -05:00
printer-tevo-flash-2018.cfg config: Add printer-tevo-flash-2018.cfg 2019-03-14 10:27:37 -04:00
printer-tronxy-x5s-2018.cfg config: Add buttons to printer-tronxy-x5s-2018.cfg 2019-03-01 00:09:30 -05:00
printer-tronxy-x8-2018.cfg Add Printer Configuration File for the Tronxy X8 2018-07-10 11:59:07 -04:00
printer-velleman-k8200-2013.cfg config: Add printer-velleman-k8200-2013.cfg example config 2018-11-13 10:46:57 -05:00
printer-wanhao-duplicator-6-2016.cfg config: Wanhao Duplicator 6 likely does not need "restart: command" 2018-09-25 14:29:05 -04:00
printer-wanhao-duplicator-i3-plus-2017.cfg config: Use .0025 as the default z step_distance in sample configs 2018-02-25 16:00:55 -05:00
printer-wanhao-duplicator-i3-v2.1-2017.cfg config: Use consistent advice on flashing the Melzi board 2018-11-13 14:32:52 -05:00
sample-macros.cfg pause_resume: update documentation 2019-01-28 11:23:52 -05:00
sample-probe-as-z-endstop.cfg config: Update sample-probe-as-z-endstop.cfg to use set_position_z=0 2019-01-07 10:26:04 -05:00