Support an "ad5206" config section so that one can configure the
digipots found on Reprap "RAMBo" boards.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow digital and PWM output pins to be setup via new config
sections. This makes it easier to setup pin configurations.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Extend the FIRMWARE_RESTART command so that it can use the firmware
"reset" command instead of the "arduino" mechanism.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Increase the default motor_off_time from 1 minute to 10 minutes. The
small value is a common source of confusion.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the example files for cartesian printers to have a 25mm/s
maximum Z velocity. It's common to use lead screws for the Z axis on
cartesians and it is unlikely one would want to drive them at 250mm/s.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the thermistor_type and thermistor_pin config variables to
sensor_type and sensor_pin. This is in preparation for support of
sensors beyond thermistors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Not all hardware has PWM support and there is no compelling reason to
use hardware PWM for fans. Change the default to use software PWM.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the mcu PWM value from an integer (0-255) to a float (0. - 1.).
Add support for limiting the maximum power (as measured over a
sufficiently long duration) to a particular heater.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of defaulting the pressure advance lookahead time to be the
same as the pressure_advance variable, allow it to be configured.
Default the new config setting (pressure_advance_lookahead_time) to
10ms.
Also, make the setting more accurate if a future move is accelerating
in the middle of the lookahead window.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There's no reason for the user to specify position_max - it can be
inferred on deltas from the endstop positions.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some XY moves at the extreme end of the build envelope could cause
excessive axis stepper movement. Check for any moves that could
possibly result in a stepper movement of more than 3 times the XY
movement and cap the move's acceleration and speed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the lookahead code to track both normal toolhead acceleration
as well as a pseudo acceleration to the point of deceleration. This
reduces the top speed of small zig-zag moves and it reduces printer
vibration during these moves.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of requiring the user enter velocity and accel parameters for
extrude only moves, calculate sane defaults from the printer's maximum
velocity and accel.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Be more clear on which parameters have defaults and which parameters
must be specified in the config.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
On a delta printer, z moves require the mcu to support the greatest
number of steps per second. However, z moves are rare, so it makes
sense to limit the velocity of z moves separately from the velocity of
normal xy moves.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the config file so the maximum accel and velocity are specified
in the "printer" section instead of the individual "stepper" sections.
The underlying code limits the velocity and accel of the toolhead
relative to the print object, so it makes sense to configure the
system that was as well.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Invert the default meaning of the stepper direction pin. Instead of
treating a low value as position motion, treat a high value as
positive motion. This matches what other firmwares do, and it matches
what common stepper motor drivers document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
A pullup setting on an input pin (ie, '^') should enable the hardware
pullup resistor, but it should not invert the trigger level (ie, it
should remain trigger on high). Those that need to change the trigger
level (ie, trigger on low) must now do that explicitly (ie, '^!').
This makes the code match what other firmwares do.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow a config file to specify 'min_extrude_temp: 0' to disable the
minimum extrude temperature test. This makes it easier to perform
testing on the avr simulator.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow the config file to specify the minimum temperature for the
extruder and check for that temperature prior to moving the extruder
motor.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for enhancing the precision of endstop switches by also
inspecting the phase of the stepper motor when the endstop triggers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a config option to define an amount of additional filament to feed
into the extruder during acceleration and deceleration of the
extruder. This can help ensure plastic is deposited in the correct
places during a print.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create a new python file (extruder.py) to control the extruder heater
and stepper motors. This separates the extruder control logic from
the cartesian robot code - making it easier to customize both the
kinematic control of the robot as well as the extruder.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor