The 'bed_shape' option has been removed. The user will enter a 'bed_radius' if they have a round be, otherwise they should enter 'min_point' and 'max_point'. When the bed is round the user should supply a 'round_probe_count' option, otherwise just 'probe_count'.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Support added for filament diameter sensor. Sample configuration parameters added to example-extras.cfg.
Signed-off-by: Mustafa YILDIZ <mydiz@hotmail.com>
Adds the ability to register a custom/generic heater through a new extra called heater_generic.
This takes a gcode_id that is reported by M105. Adds a new command to set the temperature for any heater using the syntax:
SET_HEATER_TEMPERATURE HEATER=<heater_name> TARGET=<target_temp>
Signed-off-by: John Jardine <john@gprime.net>
Example config file for a stock 250mm build VORON2 printer that
matches the manual diagrams exactly for the controller layout and pins
used.
Signed-off-by: Ben Warren <boffdroid@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Marlin examples use the "ATC Semitec 104GT-2" thermistor for the CR10,
CR10S, and CR10mini. Reported by @dovcharov.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add updates to example-extras.cfg and G-Codes.md documenting pause_resume. Also add M600 (filament change) to sample-macros.cfg.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Add support for performing linear interpolation between a set of
measured temperature/resistance pairs.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the undocumented test_sensor_pin config option into a
pin_up_touch_mode_reports_triggered option and document it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Query the bltouch state during the pin_up command to try and verify
that the probe does actually retract. This may be useful to detect if
the bltouch enters into an "error" state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Whenever a stepper driver or a heater becomes active, it is desirable to turn on a fan cooling the associated parts on the controller board. This module implements such a fan that turns on whenever a stepper or specified heater turns on, decelerates to a configurable speed when all of the watched parts turn off, and returns to an off-speed, when a user-defined timeout is met.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
This is my current config file for Fysect F6 + TMC2208 running on my
Ender 3 with stock creality display.
Signed-off-by: Simone Bonacini <bonacini.simone@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
- changes that make easier to use menu as module UI
- new helper method for delayed callbacks
- method for getting the menu instance from display
- new action for sending menu:action events
- allow_without_selection option for cards
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
- long press with timer (button release is not needed anymore)
- initial support for edit mode long press gcode
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
The sam3 i2c code and the linux code use a 7-bit i2c address, while
the avr, lpc176x, and samd21 i2c code uses an 8-bit address with the
least significant bit always zero. A similar issue occurred in the
host code (sx1509.py and replicape.py use 7-bit addresses while
uc1701.py and mcp4451.py use 8-bit addresses).
Consistently use 7-bit addresses in all the code. This breaks
compatibility between host and mcu software, so make a change to the
config_i2c command to force users to synchronize software updates.
This also breaks common Smoothieboard configs, so update the mcp4451
code to validate the i2c_address.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
I have made one change to `gcode.py` to support quoted parameter
values.
I have added support for the basic `M118` command (see
https://reprap.org/wiki/G-code#M118:_Echo_message_on_host). I have
also added a `RESPOND` command that takes extended parameters.
`ECHO` might be a better name than `RESPOND` but is already defined
in `gcode.py`.
Signed-off-by: Alec B. Plumb <alec@etherwalker.com>
There is concern that the bltouch.py module may not perform adequately
on some bltouch "clones". Document that.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It appears some bltouch "clones" do not report the probe as triggered
when put in "touch mode" while the pin is raised. Add a config option
to allow users to disable the test.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Added options necessary for basic extruder calibration expected of a new install. Fixed bed size to correct 235x235. Removed 0.5 position_endstop setting as this crashes hot end into the bed on stock Ender 3's.
Signed-off-by: Troy nadeau <troyboy162@hotmail.com>
Update documentation about the fade options. Also inform the user that it is recommended to home toward the center of the print area when using a probe for z homing.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
The example configuration information is more useful for general probe
as z_endstop than as a bltouch example.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Arksine
Kevin O'Connor
nopbit
John Jardine
Boffgithub
AxMod 3D Print
Tschipel
Ales Stimec
Rui Caridade
Master92
SimoneBnc
Janar Sööt
Yannic Schröder
Patrick Balsiger
Graham Ambrose
Alec B. Plumb
Uri Shaked
TronskiFPV
ruevs