config: Rework sample-bltouch.cfg into sample-probe-as-z-endstop.cfg

The example configuration information is more useful for general probe
as z_endstop than as a bltouch example.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
Kevin O'Connor 2018-11-25 11:50:08 -05:00
parent 7699304f9b
commit f01ced8ed4
2 changed files with 51 additions and 56 deletions

View File

@ -1,56 +0,0 @@
# This file provides example config file settings for the BLTouch
# automatic bed leveling sensor. This file is just a "snippet" of
# sections specific to the BLTouch - it must be added to a config file
# containing the configuration of the rest of the printer.
# Be sure to review and update this config with the appropriate pins
# and coordinates for your printer.
# See the "example.cfg" and "example-extras.cfg" files for a
# description of config parameters.
# Define the BLTouch servo
[servo bltouch]
pin: ar32
maximum_servo_angle: 180
minimum_pulse_width: 0.0006
maximum_pulse_width: 0.0024
# Define a probe using the BLTouch
[probe]
pin: ar30
z_offset: 2.345
activate_gcode:
SET_SERVO SERVO=bltouch ANGLE=10
SET_SERVO SERVO=bltouch ANGLE=60
G4 P200
deactivate_gcode:
SET_SERVO SERVO=bltouch ANGLE=90
G4 P100
# Example bed_tilt config section
[bed_tilt]
points:
100,100
10,10
10,100
10,190
100,10
100,190
190,10
190,100
190,190
# If the BLTouch is used to home the Z axis, then define a
# homing_override section, use probe:z_virtual_endstop as the
# endstop_pin in the stepper_z section, and do not set
# position_endstop in the stepper_z section.
#[homing_override]
#set_position_z: 5
#axes: z
#gcode:
# ; G90 ; Uncomment these 2 lines to blindly lift the Z 2mm at start
# ; G1 Z7 F600
# G28 X0 Y0
# G1 X100 Y100 F3600
# G28 Z0

View File

@ -0,0 +1,51 @@
# This file provides example config file settings for use on a printer
# that uses a Z probe instead of a traditional Z endstop switch. This
# file is just a "snippet" of config sections - it must be added to a
# config file containing the configuration of the rest of the printer.
# Be sure to review and update this config with the appropriate pins
# and coordinates for your printer.
# See the "example.cfg" and "example-extras.cfg" files for a
# description of config parameters.
# Define a probe
[probe]
pin: ar30
z_offset: 2.345
# Example settings to add to stepper_z section
[stepper_z]
endstop_pin: probe:z_virtual_endstop
position_min: -2 # The Z carriage may need to travel below the Z=0
# homing point if the bed has a significant tilt.
# The homing_override section modifies the default G28 behavior
[homing_override]
set_position_z: 5
axes: z
gcode:
; G90 ; Uncomment these 2 lines to blindly lift the Z 2mm at start
; G1 Z7 F600
G28 X0 Y0
G1 X100 Y100 F3600
G28 Z0
# Example bed_tilt config section
[bed_tilt]
points:
100,100
10,10
10,100
10,190
100,10
100,190
190,10
190,100
190,190
# Example bed_mesh config section
[bed_mesh]
min_point: 20,20
max_point: 200,200
probe_count: 4,4