Temporarily disable support for multiple languages on the main
klipper3d.org site. The search functionality isn't working correctly
with translations.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Check that a SET_PRESSURE_ADVANCE without an explicit EXTRUDER
parameter isn't done after the user disables or reassociates the
extruder stepper motor (via SYNC_EXTRUDER_MOTION). Otherwise, it
could lead to very confusing results.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
With recent changes, the extruder_stepper may be used for new
purposes, and synchronizing to the "extruder" motion queue at startup
may become a confusing default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The serial device needs to be enabled before setting the DLAB bit.
This prevented UART3 from working.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Document that spaces and special characters should not be in the
config filename.
Remove reference to step_distance and pin_map deprecated features, as
those features are now fully removed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change from the "material translate icon" to the "material language
icon" for the language selection icon. (The "material language icon"
is an alias for the "material web icon" and it seems we can't use the
alias, so we directly set the icon to "material/web".)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Lines 94 and 97. Fan speed should be 1 and not 0.5
removed lines to use default settings.
[heater_fan hotend_fan]
pin: PG14
[fan]
pin: PG13
Signed-off-by: Scott Schering <sschering@gmail.com>
The stm32 specs indicate that the SPE bit must be cleared before
changing the CPHA or CPOL bits.
Reported by @cbc02009 and @bigtreetech.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's possible for the SCLK pin to still be updating even after the
last byte of data has been read from the receive pin. (In particular
in spi mode 0 and 1.) Exiting early from spi_transfer() in this case
could result in the CS pin being raised before the final updates to
SCLK pin.
Add an additional wait at the end of spi_transfer() to avoid this
issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Deprecate SET_EXTRUDER_STEP_DISTANCE and SYNC_STEPPER_TO_EXTRUDER.
Recommend using SET_EXTRUDER_ROTATION_DISTANCE and
SYNC_EXTRUDER_MOTION.
Deprecate the extruder "shared_heater" option and reocmmend using
extruder_stepper config sections to obtain the same functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This command is a rename of SYNC_STEPPER_TO_EXTRUDER. This change is
in preparation for the removal of SYNC_STEPPER_TO_EXTRUDER.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support altering the extruder distance using the higher-level
rotation_distance. This is in preparation for removal of the
SET_EXTRUDER_STEP_DISTANCE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Separate out message parsing into individual classes. This should
make the code a little eaiser to understand.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Fritz Webering
BIGTREETECH
Pedro Lamas
Andrei Ignat
Lorenzo
Frank Tackitt
Misterke
Polar-Ted
joshindc
Yifei Ding
Wilhelm Schuster
adelyser