Previously the section for stepper_bed was intertwined with printer. This commit makes it match (../config/example-polar.cfg).
Signed-off-by: Charles Pickering <me@charlespick.xyz>
Added PCA9632 LED module support using software I2C from MCP4018
modulo drive the LED strip of a FlashForge Dreamer 3D printer.
Based on the PCA9533 module.
Signed-off-by: Ricardo Alcantara <ricardo@vulcanolabs.xyz>
With recent changes, the extruder_stepper may be used for new
purposes, and synchronizing to the "extruder" motion queue at startup
may become a confusing default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Document that spaces and special characters should not be in the
config filename.
Remove reference to step_distance and pin_map deprecated features, as
those features are now fully removed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change from the "material translate icon" to the "material language
icon" for the language selection icon. (The "material language icon"
is an alias for the "material web icon" and it seems we can't use the
alias, so we directly set the icon to "material/web".)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Deprecate SET_EXTRUDER_STEP_DISTANCE and SYNC_STEPPER_TO_EXTRUDER.
Recommend using SET_EXTRUDER_ROTATION_DISTANCE and
SYNC_EXTRUDER_MOTION.
Deprecate the extruder "shared_heater" option and reocmmend using
extruder_stepper config sections to obtain the same functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This command is a rename of SYNC_STEPPER_TO_EXTRUDER. This change is
in preparation for the removal of SYNC_STEPPER_TO_EXTRUDER.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support altering the extruder distance using the higher-level
rotation_distance. This is in preparation for removal of the
SET_EXTRUDER_STEP_DISTANCE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Break listing up by module name. Provide links to "extended"
commands. Sort reference by module name.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's no longer necessary to update the printer.cfg file to alter the
max_accel and square_corner_velocity parameters. Update the
Resonance_Compensation.md document to reflect this.
Also, recommend using STEP_DELTA in the TUNING_TOWER commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Wraps lines to 80 columns. Only use triple backticks on multi-line
code excerpts. Add backticks around "sudo raspi-config". Move
"Enabling SPI" section to be near pwm and gpio configuration.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Refactor the extruder_stepper support so that it uses the
ExtruderStepper class defined in extruder.py.
Support the SYNC_STEPPER_TO_EXTRUDER command on steppers defined in
either extruder_stepper or extruder config sections.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is preferable to program the tmc drivers with an irun (or cs)
setting near 31, as otherwise the driver may have reduced microstep
precision. It was possible for the driver to be programmed with
irun=16 or irun=17 when it could have been configured with irun=31
with vsense=1 instead. This would occur on tmc2130/tmc2208/tmc2209
drivers for values around 0.900 to 1.000 amps (when using a typical
sense_resistor settings of 0.110 Ohms).
Change the code to prefer using vsense=1 to avoid this issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Many non-English speaking countries use a comma as a decimal separator for printed numbers. This can create some confusion in documentation and config files when not surrounded by contextual clues like parenthesis. Improve documentation by adding spaces to coordinates.
Signed-off-by: Paul McGowan <mental450@gmail.com>
Charles Pickering
Kevin O'Connor
Ricardo Alcântara
electron2410
Fritz Webering
Pedro Lamas
Misterke
Yifei Ding
Wilhelm Schuster
Haxk20
Dmitry Butyugin
Tim Abraham
Paul McGowan