Use the generic spi send/receive code on Linux. Update the replicape
code to use the updated command format.
Also, update the replicape code to turn off the stepper motors on a
shutdown event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improve the SPI message transmit system. Add support for bus speed
and bus mode. Add support for sending SPI messages on shutdown.
Signed-off-by: Petri Honkala <cruwaller@gmail.com>
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a set_shutdown_speed() method so that the heater_fan code does not
need to peek into the fan object's internal members.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When using an automatic probe, limit the Z lift speed to be no greater
than the Z probing speed. This can reduce Z jerks during probing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the fan's max power is limited by the config, then scale speed
requests between 0 and max_power. This makes more sense for typical
g-code fan speeds.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of supporting a single linear range for the temperature
lookup, allow multiple ranges to be defined. This makes the lookup
more accurate when a full lookup table is available.
Update the AD595 sensor to use the full table defined in its spec.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the c3 coefficient is negative it can cause the adc calculations to
fail. The c3 shouldn't be negative in practice, so fallback to a
simple beta calculation in that case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the Thermistor code to a new thermistor.py module. Move the
Linear code to a new adc_temperature.py module. This simplifies the
heater.py code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Thermistor (and Linear) class should handle all the details of
reading the ADC values and converting them to temperatures. So, move
that logic out of the Heater() class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a PrinterHeaters class that can stores references to available
temperature sensors and stores references to instantiated heaters.
Add a extras/heater_bed.py file and delay instantiation of the
heater_bed object. This allows the heater.py module to be imported
earlier during the setup phase, and allows the PrinterHeaters class to
be available for registering sensors and heaters.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Most callers did a lookup of the pins module via
printer.lookup_object("pins"). Use that as the standard method and
remove these less frequently used methods.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Apply the bed tilt settings immediately after finding them. This
makes it easier for users to perform automatic tilt calibration at the
start of every print.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Drop support for M303 and PID_TUNE, and replace it with a new
PID_CALIBRATE command. Move the logic for this command from heater.py
to a new pid_calibrate.py file in the extras/ directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the probe_z_offset parameter from delta_calibrate and
bed_tilt_calibrate to a z_offset parameter within the probe config
section. It's easier to understand the z offset setting when it is in
the probe config section.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a z_virtual_endstop is in use, then record the last XY position
that is used when the Z is homed. Use that XY position to report what
change is needed to the z position_endstop.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the digital_output, pwm_output, and static_pwm_output config
sections to output_pin and move to a new module in the extras/
directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the code for the static_digital_output config section from
chipmisc.py to a new file in the extras/ directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a heater falls out of the target range, accumulate the temperature
differences to determine if an error should be raised. This should
make it less likely to report an error for heaters that drift slightly
out of range, and it should make error reporting faster for heaters
that rapidly fall out of range.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
A default of 4 degrees and 10 seconds may be too aggressive - change
the default to 10 degrees and 15 seconds.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Separate out the hd44780 screen drawing from the st7920 code. Use a
layout that takes advantage of the 20 columns. Add custom hd44780
fonts.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for displaying basic status information on ST7920 and
HD44780 based LCDs that are attached directly to a micro-controller.
Signed-off-by: Marcio Teixeira <marcio@alephobjects.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a lookup_command() method to the SerialReader class that provides
a wrapper that stores the serial and commandqueue references. This
makes it easier to run the send() method.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for directly printing from a local file on the host. This
may be useful if the host cpu is not fast enough to run OctoPrint
well.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The bed_tilt_calibrate command determines the tilt of the bed.
However, we need to report the tilt compensation which is the negative
of the bed tilt.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use both load_config() and load_config_prefix() functions when
dynamically loading a module from the extras directory - if the config
section name has parameters in it then use load_config_prefix().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Specify hardware pwm cycle times using the same method as software pwm
(in seconds, not clock ticks). Allow the fan code to be configured
with an explicit cycle time even when using software pwm.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for disabling homing checks via the homing_override
mechanism. This may be useful to move an axis prior to homing it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create a virtual pin that may be used as the z endstop pin on
cartesian printers that use the probe in place of a z endstop.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow a set of g-code scripts to be run on each probe invocation.
This may be useful for probes that need to be setup before they are
useful (eg, with servo actuated probes).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow users to override the behavior of G28 using a new
"homing_override" config section. This may be used on printers that
require specific steps during the homing process.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The print cooling fan and printer heater_fan are independent modules
that can reside in the extras directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Check if a config section matches a python filename in the
klippy/extras/ directory. If it does, load that python code to handle
the config section.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Marcio Teixeira