Start the raise sequence once the endstop notification arrives. This
can reduce the response time as it does not require waiting for the
homing sequence to fully finalize.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If reset_last_position() is invoked prior to the printer being
"ready", then the transform may not be properly accounted for. Handle
this by calling reset_last_position() when the printer becomes
"ready".
This should fix some "must home first" errors on extrude-only moves.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only set resend_interval if a mcu_duration is specified. This fixes a
bug introduced in commit 861144d8.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Times longer than 5 seconds may result in a 32bit ticks overflow in
the micro-controller (for fast micro-controllers).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Module which bring support for P2 devices running in connected mode. This enables using a Palette2 directly with Klippy without Octoprint, or without Palette2 plugins for Octoprint which are not functional out of the box with Klipper.
Signed-off-by: Clifford Roche <clifford.roche@gmail.com>
The input shaper can only reduce vibrations by 20x. Therefore,
the best-case achievable vibrations level is max(psd) / 20.
Any vibrations below that level can be ignored for the prupose
of input shaper scoring. This allows tuning script to ignore
wide tails of resonances, because it is not helpful to try to
reduce them with input shaping.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
HTU21D sensor class lacked the method `get_report_time_delta` invoked
during watermark control loops. This short fix simply adds that method
in, calling the `self.report_time` attribute created during class
construction.
Signed-off-by: Jon Sanders <jonsan@gmail.com>
This adds support for BMP280 and BME680 sensor ICs,
along with fixing calibration data readout for BME280.
Gas sensor readout for the BME680 is just the raw compensated value.
To get actual meaningful values, more research is needed.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
The tmc2660 spec has an ambiguous "SG" field that sometimes refers to
the "stallGuard" flag and sometimes refers to the "SG_RESULT" field.
The tmc2130 and tmc5160 have similar fields that are not ambiguous, so
adopt that naming strategy.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add functionality to support a Filament Motion Sensor for detecting extruder jams as well as runouts. Works by an encoder toggling the switch_pin 0/1 as the filament is pulled through the sensor.
Signed-off-by: Joshua Wherrett <thejoshw.code@gmail.com>
The tmcuart_send command increases cpu usage on the micro-controller.
Should multiple tmcuart_send commands be issued at the same time to a
single AVR micro-controller, it could increase the load to the point
that it introduces a failure. It could also lead to tmcuart_send
transmission errors, which would cause retransmission requests, which
further increase the load.
Track and share mutexes so that only one tmcuart_send command can be
active on a single mcu at a time.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The tmc2130 (and tmc5160) will respond back with the value written
during the next SPI command. Use this feature to verify that the
value written matches the value sent.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
None of the other TMC driver enable SFILT by default and it seems
enabling SFILT may not be ideal for sensorless homing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Machines that have no heaters produce an error when the idle timeout occurs. This commit fixes this by checking if there are any heaters to turn off.
Signed-off-by: Florian Heinze <florian@heinze.at>
Introduce a heaters.set_temperature() command and call that from
commands that set a heater temperature. This new function calls
toolhead.register_lookahead_callback() so that the idle_timeout gets
notification that activity has occurred.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add new fields to Command_Templates.md.
Remove unused self.rpm variable.
Use an explicit get_frequency() method in keeping with Klipper's
convention of not "peeking into member variables".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This adds new config options for fans: 'tachometer_pin' to specify the
GPIO pin, and 'tachometer_ppr' (default 2) to specify the number of
signal pulses per revolution. The rpm is also exposed by get_status for
command templates and the API server. For fast fans (at least 10000
RPM), the polling interval can be shortened using the
'tachometer_poll_interval' option.
There is a new mcu object for a generic edge counter, which repeatedly
polls a GPIO pin and periodically reports the count to the host.
Signed-off-by: Adrian Keet <arkeet@gmail.com>
With commit 53b10d3a the setup of sensorless homing could occur before
the driver was enabled which would cause the reinitialization of the
driver settings to undo the sensorless homing setup.
Use set_field() when setting the sensorless homing registers so that
it wont conflict with a driver init.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Check the status of all Trinamic stepper motor drivers once a second.
If the driver reports an error then invoke a shutdown. Also log any
serious warnings.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Send the full TMC stepper motor driver initialization sequence every
time the driver is enabled.
Don't raise an error on startup if unable to contact a tmc2208/tmc2209
driver. If the driver is still unavailable when it is enabled then a
shutdown will be issued. This allows users to troubleshoot (and
possibly bring up communication to the driver) prior to enabling the
driver.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The tmc2660 appears to send responses as soon as the clk starts
toggling. That means the 20 bit response is at the top of the 24bit
sent message. Also, this implies that RDSEL must already have the
correct value in the prior message.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Where the tmc2660 flags match other drivers, use lowercase so that the
same monitoring code can be used for all the tmc drivers. Also, use
the same field formatters where applicable.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The tmc5160 field formatters were mostly duplicates of the tmc2130 -
add the "reset" field to tmc2130.py so both drivers have similar
reporting.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Refactor the tmc driver implementations so that there is a single
implementation of the SET_TMC_CURRENT command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
currently, if there are 2 files on the virtual sd card whose names differ only in
case (eg. MyFile.gcode vs myfile.gcode) the actual file that gets loaded is at
best unpredictable. this patch checks for an exact match before attempting a
case-insensitive one.
Signed-off-by: Andre LeBlanc <andrepleblanc@gmail.com>
This patch adds the ability to daisy-chain multiple tmc2130 and
tmc5160 drivers.
Signed-off-by: Marco D'Alessio <marco@wrecklab.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This reverts commit ac61f8b726.
Many temperature sensors are capitalized, so don't make this chaneg to
the bme280.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Initial commit of code to support 1-wire (Dallas) sensors such
as the DS18B20. Requires Linux kernel drivers to create a file
in /sysfs which is read by this module, and temperature
typically returned to a temperature_fan.
Signed-off-by: Alan Lord <alanslists@gmail.com>
Signed-off-by: Josh Headapohl <joshhead@gmail.com>
Call mcu_adc.setup_minmax() even in debug output mode so that the
debugging output contains a more accurate configuration.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a get_status() method returns a mutable object (such as a list or
dict) then it would be possible for a gcode command template to
incorrectly alter the program's internal state. Perform a deepcopy()
operation on all get_status() return results to avoid that.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Since Python 2.6, the BaseException.message attribute is deprecated (PEP-352[1])
in favor of e.args[0] or str(e). This commit replaces e.message with str(e).
[1] https://www.python.org/dev/peps/pep-0352/
Signed-off-by: Maël Kerbiriou <m431.kerbiriou@gmail.com>
Commit ea85d419 moved CommandError from homing.py to gcode.py, but
failed to fix the references to CommandError within homing.py. Fix
that.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improved algorithm to choose the 'optimal' shaper frequency taking
shaper smoothing into account. This may choose a frequency with
slightly more vibrations but less smoothing. Also allow users to
limit the maximum input shaper smoothing.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Add support for automatically calculating the internal step_distance
from new config parameters - rotation_distance, microsteps,
full_steps_per_rotation, and gear_ratio.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The previous init sequence relied on the display ignoring commands if
they are sent faster than 40us. Some displays may not have this
limit.
Rework the init to make it more robust to command transmission times.
The new init should still transition the display into 4-bit mode even
if the display processes commands faster than 40us.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
- remove lot of helper methods
- differentiate class instantiate from config or directly
- don't use 'enable' template rendering when static value is used.
- new element 'disabled'
- other internal adjustments
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
Don't use the reactor eventtime to schedule micro-controller commands
as that time may have low accuracy.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't use the reactor eventtime to schedule micro-controller commands
as that time may have low accuracy.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Writes to the max31856 chip use "burst mode", so only one address
during the initialization sequence can be sent. This fixes erroneous
"Cold Junction Fault" errors.
Reported by @NBouquain.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an 'mcu' option to the board_pins config and use that to specify
the name of the mcu to apply the aliases to. Support applying the
aliases to multiple mcus.
Add support for any number of options starting with an "aliases_"
prefix.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move all the config reference information from files in the config/
directory to a new Config_Reference.md document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Queue updates so that delays between updates are properly applied.
This fixes macros that would blink LEDs by pausing between update
commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Users may use this action to call methods registered by a webhooks client from a command template.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
It is only valid to call raise_probe() when the toolhead is not
moving. Make sure to call sync_print_time() from multi_probe_end() to
ensure that. This fixes a bug that could cause the Z axis steppers to
lose their position when "stow_on_each_sample=False".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
On a reset, the mcu.py code may have sent an initialization message to
the bltouch, which needs time to complete. Add additional time during
the bltouch setup to avoid a race with these two times. This avoids
some "timer too close" errors that users of fast host machines were
reporting.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M117 command parser discards the last character of the message
whenever the M117 command does not begin the line and there is no *xx
checksum, e.g.
N0 M117 Look at me
causes the banner area of the printer screen to display "Look at m".
This patch only trims the checksum when one is found to trim.
Signed-Off-By: Jonathan Pickard <jhp@adjustablelabs.info>
Add get_status wrapper with last_query status for macros It is sometimes useful to determine the state of the probe from a macro. If the probe is connected to an endstop pin, the results can be obtained via QUERY_ENDSTOPS but if a physical endstop is in use in addition to the probe the probe state cannot be obtained. This change allows one to use QUERY_PROBE and then access the printer.probe.last_query object to obtain the state.
Signed-off-by: Paul McGowan <mental405@gmail.com>
Update callers to use the printer.command_error reference instead of
directly using homing.CommandError() when raising or catching errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There's no reason to distinguish between an EndstopError and a
CommandError, so just use CommandError.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Increase the maximum redraw rate from 4 times per second to 10 times
per second. Some users have reported slower rendering times as a
result of 8fa1c977.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Split up the main GCodeParser class into GCodeDispatch and GCodeMove
classes. The GCodeMove class is now available using the "gcode_move"
printer object name. This split simplifies the gcode.py code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename printer.gcode.action_emergency_stop() to
action_emergency_stop(), printer.gcode.action_respond_info() to
action_respond_info(), and printer.gcode.action_respond_error() to
action_raise_error() in command templates.
This simplifies the get_status() interface, as returning callable
functions from that interface was confusing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a helper function for submitting relative movements. This
function will also automatically ensure gcode.reset_last_position() is
called.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Generate a "toolhead:set_position" event on a call to
toolhead.set_position() and use that event to automatically call
gcode.reset_last_position().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a request_redraw() method and call it when a key menu event
occurs. Limit these proactive screen redraws to no more than 4 per
second.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
After reading the first item of self.filament_array, filament_width is updated back to self.nominal_filament_dia or self.diameter instead of retaining the value until next pending_position.
Updated Filament Menu Template.
Signed-off-by: Nicola Falciani <nicola.fal@gmail.com>
- don't populate all items at once
- populate items when container is pushed to stack
- precreate List back item, don't create it during populate.
- don't update items during populate
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
Use the "info" webhook to pass critical process information back to
the caller. The remaining users of register_static_path() can get the
required information via get_status() calls.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
In case of an overwriting existing menu item,
the new item was added additionally to the end of the items list.
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
menu.cfg:
- jinja2 template scripting
- new Setup menu
- new Calibration menu
menu:
- redesigned menu code
- jinja2 support
- option to reverse menu up and down directions
- functionality set to support menu injection from other modules
- a new way of defining menu hierarchy
- other adjustments
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
Arc travel was working but extrusion in absolute mode seemed not to be happening at all. This was because the E coord being sent with each G1 segment of the arc was not incrementing, effectively the same value was being sent over and over so the total extrusion for the whole arc was the amount for just one segment which is an extremely tiny amount.
My change increments e_base by e_per_move for each subsequent coord when in absolute extrude mode which results in the correct absolute E value being sent for each segment.
Signed-off-by: Toby Harper <toby@fuith.org>
SDCARD_PRINT_FILE allows Klipper to load and start the print for any
gcode file within the virtual_sdcard path, including subdirectories.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
In it's current behavior, safe_z_home will attempt to home Z if it thinks the toolhead is above the z endstop even if the motors have since been disabled and the toolhead was moved to another position
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
This streamlines the BedMeshCalibrate class, making it only resposible for configuring and executing the calibration procedure.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Using the setup_start_value() method avoids the PWM output line
transitioning to an intermediate state prior to setting the initial
value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add user-configurable contrast, vcomh (affects "smearing"), and invert options for SSD1306/SH1106 type OLED displays.
Signed-off-by: James Esau <james_esau@hotmail.com>
Input shaping can help to reduce printer vibrations due to resonances
and eliminate or reduce ghosting in prints.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Register API endpoints for "pause_resume/pause", "pause_resume/resume" and "pause_resume/cancel".
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Kevin O'Connor
le-Bark
Dmitry Butyugin
Arksine
Denis Ignatenko
Pascal P
Clifford Roche
Janar Sööt
Jon Sanders
Michael Kurz
TheJoshW
fleinze
teeminus
Adrian Keet
Andre LeBlanc
Marco D'Alessio
Evgenii
Christian S
Arjan Mels
Alan Lord
Lane Roberts
Thomas Kroll
Chip
Pascal P
Alex Zellner
Maël Kerbiriou
Justin Schuh
Stefan Dej
Al
Martin Hierholzer
Arksine
jhpadjustable
Paul McGowan
rjpatawaran
alocin73
Bryan Boettcher
Trevor Jones
Toby Harper
bondus
Florian Heilmann
combolek
Iakabos