If the fan's max power is limited by the config, then scale speed
requests between 0 and max_power. This makes more sense for typical
g-code fan speeds.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit e3f9ff67 changed the probe code to require a z_offset parameter
- update the config/sample-bltouch.cfg file with the new parameters.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Drop support for M303 and PID_TUNE, and replace it with a new
PID_CALIBRATE command. Move the logic for this command from heater.py
to a new pid_calibrate.py file in the extras/ directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the probe_z_offset parameter from delta_calibrate and
bed_tilt_calibrate to a z_offset parameter within the probe config
section. It's easier to understand the z offset setting when it is in
the probe config section.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the digital_output, pwm_output, and static_pwm_output config
sections to output_pin and move to a new module in the extras/
directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a heater falls out of the target range, accumulate the temperature
differences to determine if an error should be raised. This should
make it less likely to report an error for heaters that drift slightly
out of range, and it should make error reporting faster for heaters
that rapidly fall out of range.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
A default of 4 degrees and 10 seconds may be too aggressive - change
the default to 10 degrees and 15 seconds.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for additional carriages on cartesian printers. This is
used by some printers to handle multiple extruders.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Working printer configuration for a Wanhao Duplicator i3 v2.1 and its
clones, including Monoprice Maker Select and Cocoon Create. Includes a
working config for the st7920-based front panel LCD.
Signed-off-by: Andy Ellsworth <andy+github@dar.net>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
I've added the LCD configuration for the Tronxy X5S printer and its
Melzi board and 128x64 LCD. This is tested and works.
I've also added the pins for the encoder, but that is untested.
Signed-off-by: christian mock <cm@tahina.priv.at>
Add support for displaying basic status information on ST7920 and
HD44780 based LCDs that are attached directly to a micro-controller.
Signed-off-by: Marcio Teixeira <marcio@alephobjects.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the description of stepper phase adjusted endstops to a new
section in config-extra.cfg. This keeps the main example config file
a little more concise.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't use tiny step distances on the Z as that could cause a surprise
to users that copy the config without updating all the settings. (A Z
step distance that is too small would cause a high motor velocity.) A
step distance of .0025 is very popular in practice, so change the
default example configs to use that.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an example to help users with a BLTouch probe. This is based on
information from @mediumo and @riddlez666.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a prefix to the example printer config files so that a sorted
directory listing shows all the samples bundled together.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for directly printing from a local file on the host. This
may be useful if the host cpu is not fast enough to run OctoPrint
well.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Specify hardware pwm cycle times using the same method as software pwm
(in seconds, not clock ticks). Allow the fan code to be configured
with an explicit cycle time even when using software pwm.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the mcu supports command restarts and it does not appear to use a
real serial port, then default the restart method to 'command'. This
is a better default on boards with native USB support.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for disabling homing checks via the homing_override
mechanism. This may be useful to move an axis prior to homing it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create a virtual pin that may be used as the z endstop pin on
cartesian printers that use the probe in place of a z endstop.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow a set of g-code scripts to be run on each probe invocation.
This may be useful for probes that need to be setup before they are
useful (eg, with servo actuated probes).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow users to override the behavior of G28 using a new
"homing_override" config section. This may be used on printers that
require specific steps during the homing process.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Grigori Goronzy
Arkadiusz Gluszyk
ghandye
christian mock