2018-07-02 18:28:19 +02:00
|
|
|
# This file contains a configuration for the "Anycubic Kossel Linear
|
|
|
|
|
# Plus Large Printing Size", "Anycubic Kossel Pulley Plus Large
|
2018-11-24 14:12:33 +01:00
|
|
|
# Printing Size" and similar delta printer from 2017.
|
|
|
|
|
# The Anycubic delta printers use the TriGorilla board which is an
|
|
|
|
|
# AVR ATmega2560 Arduino + RAMPS compatible board.
|
|
|
|
|
# To use this config, the firmware should be compiled for the AVR atmega2560.
|
2020-05-02 15:31:23 +02:00
|
|
|
# See the example.cfg, example-delta.cfg and example-extras.cfg files
|
|
|
|
|
# for a description of available parameters.
|
2018-07-02 18:28:19 +02:00
|
|
|
|
|
|
|
|
[stepper_a]
|
|
|
|
|
step_pin: ar54
|
|
|
|
|
dir_pin: !ar55
|
|
|
|
|
enable_pin: !ar38
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^ar2
|
|
|
|
|
homing_speed: 60
|
|
|
|
|
# The next parameter needs to be adjusted for
|
|
|
|
|
# your printer. You may want to start with 280
|
|
|
|
|
# and meassure the distance from nozzle to bed.
|
|
|
|
|
# This value then needs to be added.
|
|
|
|
|
position_endstop: 295.6
|
2019-12-02 00:51:46 +01:00
|
|
|
arm_length: 269.0
|
2018-07-02 18:28:19 +02:00
|
|
|
|
|
|
|
|
[stepper_b]
|
|
|
|
|
step_pin: ar60
|
|
|
|
|
dir_pin: !ar61
|
|
|
|
|
enable_pin: !ar56
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^ar15
|
|
|
|
|
|
|
|
|
|
[stepper_c]
|
|
|
|
|
step_pin: ar46
|
|
|
|
|
dir_pin: !ar48
|
|
|
|
|
enable_pin: !ar62
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^ar19
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: ar26
|
|
|
|
|
dir_pin: !ar28
|
|
|
|
|
enable_pin: !ar24
|
2019-12-02 00:51:46 +01:00
|
|
|
step_distance: 0.0104166
|
2018-07-02 18:28:19 +02:00
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: ar10
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: analog13
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 25.349
|
|
|
|
|
pid_Ki: 1.216
|
|
|
|
|
pid_Kd: 132.130
|
|
|
|
|
min_extrude_temp: 150
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 275
|
|
|
|
|
|
2019-12-02 00:51:46 +01:00
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: ar8
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: analog14
|
|
|
|
|
control: pid
|
|
|
|
|
pid_kp: 73.517
|
|
|
|
|
pid_ki: 1.132
|
|
|
|
|
pid_kd: 1193.728
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 130
|
2018-07-02 18:28:19 +02:00
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: ar9
|
|
|
|
|
kick_start_time: 0.200
|
|
|
|
|
|
|
|
|
|
[heater_fan extruder_cooler_fan]
|
|
|
|
|
pin: ar44
|
|
|
|
|
|
2019-12-02 00:51:46 +01:00
|
|
|
# if you want to use your probe for DELTA_CALIBRATE you will need that
|
|
|
|
|
#[probe]
|
|
|
|
|
#pin: ^ar18
|
|
|
|
|
#z_offset: 15.9
|
|
|
|
|
#samples: 3
|
|
|
|
|
|
2018-07-02 18:28:19 +02:00
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/ttyUSB0
|
|
|
|
|
pin_map: arduino
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: delta
|
2018-11-24 14:12:33 +01:00
|
|
|
max_velocity: 500
|
2018-07-02 18:28:19 +02:00
|
|
|
max_accel: 3000
|
|
|
|
|
max_z_velocity: 200
|
2019-12-02 00:51:46 +01:00
|
|
|
delta_radius: 134.4
|
2018-07-02 18:28:19 +02:00
|
|
|
# if you want to DELTA_CALIBRATE you may need that
|
|
|
|
|
#minimum_z_position: -5
|
|
|
|
|
|
2018-07-13 01:07:54 +02:00
|
|
|
[idle_timeout]
|
|
|
|
|
timeout: 360
|
|
|
|
|
|
2019-12-02 00:51:46 +01:00
|
|
|
[delta_calibrate]
|
|
|
|
|
radius: 115
|
2020-05-02 15:31:23 +02:00
|
|
|
# If the original probe is used
|
|
|
|
|
#horizontal_move_z: 20
|
2018-07-02 18:28:19 +02:00
|
|
|
|
|
|
|
|
# "RepRapDiscount 2004 Smart Controller" type displays
|
|
|
|
|
[display]
|
|
|
|
|
lcd_type: hd44780
|
|
|
|
|
rs_pin: ar16
|
|
|
|
|
e_pin: ar17
|
|
|
|
|
d4_pin: ar23
|
|
|
|
|
d5_pin: ar25
|
|
|
|
|
d6_pin: ar27
|
|
|
|
|
d7_pin: ar29
|
2018-10-26 03:34:49 +02:00
|
|
|
encoder_pins: ^ar31, ^ar33
|
|
|
|
|
click_pin: ^!ar35
|
|
|
|
|
kill_pin: ^!ar41
|
