| .. |
|
atsam
|
atsam: Configure the atsam sram matrix register
|
2019-02-07 13:12:35 -05:00 |
|
atsamd
|
atsamd: Enable ADC support for samd51 devices (#1204)
|
2019-02-08 12:02:32 -05:00 |
|
avr
|
avr: Only prompt for CLEAR_PRESCALER and SIMULAVR with LOW_LEVEL_OPTIONS
|
2019-01-25 18:07:31 -05:00 |
|
generic
|
armcm_timer: Add a generic timer mechanism for ARM CortexM3/M4 chips
|
2019-02-06 22:03:09 -05:00 |
|
linux
|
linux: Add support for bi-directional SPI communication
|
2018-07-24 11:16:05 -04:00 |
|
lpc176x
|
lpc176x: Convert code to use armcm_timer
|
2019-02-06 22:03:09 -05:00 |
|
pru
|
pru: Add wrappers for gpio_x_reset()
|
2018-08-27 12:45:01 -04:00 |
|
simulator
|
simulator: Fix simulator build
|
2019-01-25 18:23:27 -05:00 |
|
stm32f1
|
stm32f1: Convert code to use armcm_timer
|
2019-02-06 22:03:09 -05:00 |
|
Kconfig
|
atsamd: Initial support for SAMD51
|
2019-01-28 20:02:16 -05:00 |
|
Makefile
|
Add generic i2c interface
|
2018-10-27 10:34:28 -04:00 |
|
adccmds.c
|
adccmds: Run gpio_adc_setup() before oid_alloc()
|
2019-01-13 11:03:30 -05:00 |
|
basecmd.c
|
basecmd: Rename get_status to get_clock
|
2018-05-29 10:57:29 -04:00 |
|
basecmd.h
|
pru: Support config_reset command to manually reset mcu
|
2017-09-03 23:16:38 -04:00 |
|
buttons.c
|
buttons: Clear pressed/last_pressed state on new buttons_query command
|
2018-10-01 12:40:28 -04:00 |
|
byteorder.h
|
byteorder: Add a header file defining common byteswap functions
|
2018-05-21 09:44:40 -04:00 |
|
command.c
|
command: Wait to send ack until after processing commands
|
2018-05-28 10:43:40 -04:00 |
|
command.h
|
command: Wait to send ack until after processing commands
|
2018-05-28 10:43:40 -04:00 |
|
compiler.h
|
compiler.h: Check if __aligned and __section macros are already defined
|
2016-06-13 23:18:59 -04:00 |
|
ctr.h
|
build: Avoid linker magic in compile_time_request.c unique id generation
|
2017-05-26 12:32:02 -04:00 |
|
debugcmds.c
|
debugcmds: Add support for reading/writing 32bit values
|
2019-02-07 11:50:14 -05:00 |
|
endstop.c
|
endstop: Eliminate end_stop_set_oversample command
|
2017-10-12 11:59:27 -04:00 |
|
gpiocmds.c
|
gpiocmds: Add update_digital_out command
|
2018-06-27 12:10:39 -04:00 |
|
i2ccmds.c
|
i2ccmds: Pass the i2c address as a 7-bit number (0-127)
|
2019-01-07 20:00:44 -05:00 |
|
lcd_hd44780.c
|
lcd_hd44780: Add micro-controller code for the HD44780 LCD chip
|
2018-03-06 11:30:34 -05:00 |
|
lcd_st7920.c
|
lcd_st7920: Use a longer delay at the start of each command/data
|
2018-06-22 23:47:09 -04:00 |
|
pwmcmds.c
|
gpiocmds: Allow the start value for a pin to differ from the default_value
|
2017-10-12 11:59:27 -04:00 |
|
sched.c
|
sched: Force sched_try_shutdown to be inlined
|
2018-10-13 11:47:00 -04:00 |
|
sched.h
|
pru: Support config_reset command to manually reset mcu
|
2017-09-03 23:16:38 -04:00 |
|
spicmds.c
|
spicmds: Check for an incorrect mode in spicmds.c
|
2018-11-30 11:50:48 -05:00 |
|
spicmds.h
|
thermocouple: Add initial support for common SPI temperature sensing chips
|
2018-07-24 11:16:05 -04:00 |
|
stepper.c
|
stepper: Fix bug when using a non-zero CONFIG_STEP_DELAY on AVR
|
2019-01-11 12:04:03 -05:00 |
|
stepper.h
|
stepper: Introduce stepper_get_position command and remove from endstop.c
|
2017-03-09 14:54:52 -05:00 |
|
thermocouple.c
|
thermocouple: Minor fixes
|
2018-07-25 09:06:50 -04:00 |
|
tmcuart.c
|
tmc2208: Initial support for configuring TMC2208 drivers
|
2018-08-27 12:51:27 -04:00 |
af0d292e23