mirror of https://github.com/Desuuuu/klipper.git
429 lines
16 KiB
Markdown
429 lines
16 KiB
Markdown
# Benchmarks
|
|
|
|
This document describes Klipper benchmarks.
|
|
|
|
## Micro-controller Benchmarks
|
|
|
|
This section describes the mechanism used to generate the Klipper
|
|
micro-controller step rate benchmarks.
|
|
|
|
The primary goal of the benchmarks is to provide a consistent
|
|
mechanism for measuring the impact of coding changes within the
|
|
software. A secondary goal is to provide high-level metrics for
|
|
comparing the performance between chips and between software
|
|
platforms.
|
|
|
|
The step rate benchmark is designed to find the maximum stepping rate
|
|
that the hardware and software can reach. This benchmark stepping rate
|
|
is not achievable in day-to-day use as Klipper needs to perform other
|
|
tasks (eg, mcu/host communication, temperature reading, endstop
|
|
checking) in any real-world usage.
|
|
|
|
In general, the pins for the benchmark tests are chosen to flash LEDs
|
|
or other innocuous pins. **Always verify that it is safe to drive the
|
|
configured pins prior to running a benchmark.** It is not recommended
|
|
to drive an actual stepper during a benchmark.
|
|
|
|
### Step rate benchmark test
|
|
|
|
The test is performed using the console.py tool (described in
|
|
[Debugging.md](Debugging.md)). The micro-controller is configured for
|
|
the particular hardware platform (see below) and then the following is
|
|
cut-and-paste into the console.py terminal window:
|
|
```
|
|
SET start_clock {clock+freq}
|
|
SET ticks 1000
|
|
|
|
reset_step_clock oid=0 clock={start_clock}
|
|
set_next_step_dir oid=0 dir=0
|
|
queue_step oid=0 interval={ticks} count=60000 add=0
|
|
set_next_step_dir oid=0 dir=1
|
|
queue_step oid=0 interval=3000 count=1 add=0
|
|
|
|
reset_step_clock oid=1 clock={start_clock}
|
|
set_next_step_dir oid=1 dir=0
|
|
queue_step oid=1 interval={ticks} count=60000 add=0
|
|
set_next_step_dir oid=1 dir=1
|
|
queue_step oid=1 interval=3000 count=1 add=0
|
|
|
|
reset_step_clock oid=2 clock={start_clock}
|
|
set_next_step_dir oid=2 dir=0
|
|
queue_step oid=2 interval={ticks} count=60000 add=0
|
|
set_next_step_dir oid=2 dir=1
|
|
queue_step oid=2 interval=3000 count=1 add=0
|
|
```
|
|
|
|
The above tests three steppers simultaneously stepping. If running the
|
|
above results in a "Rescheduled timer in the past" or "Stepper too far
|
|
in past" error then it indicates the `ticks` parameter is too low (it
|
|
results in a stepping rate that is too fast). The goal is to find the
|
|
lowest setting of the ticks parameter that reliably results in a
|
|
successful completion of the test. It should be possible to bisect the
|
|
ticks parameter until a stable value is found.
|
|
|
|
On a failure, one can copy-and-paste the following to clear the error
|
|
in preparation for the next test:
|
|
```
|
|
clear_shutdown
|
|
```
|
|
|
|
To obtain the single stepper benchmarks, the same configuration
|
|
sequence is used, but only the first block of the above test is
|
|
cut-and-paste into the console.py window.
|
|
|
|
To produce the benchmarks found in the [Features](Features.md) document, the total
|
|
number of steps per second is calculated by multiplying the number of
|
|
active steppers with the nominal mcu frequency and dividing by the
|
|
final ticks parameter. The results are rounded to the nearest K. For
|
|
example, with three active steppers:
|
|
```
|
|
ECHO Test result is: {"%.0fK" % (3. * freq / ticks / 1000.)}
|
|
```
|
|
|
|
The benchmarks are run with parameters suitable for TMC Drivers. For
|
|
micro-controllers that support `STEPPER_BOTH_EDGE=1` (as reported in
|
|
the `MCU config` line when console.py first starts) use
|
|
`step_pulse_duration=0` and `invert_step=-1` to enable optimized
|
|
stepping on both edges of the step pulse. For other micro-controllers
|
|
use a `step_pulse_duration` corresponding to 100ns.
|
|
|
|
### AVR step rate benchmark
|
|
|
|
The following configuration sequence is used on AVR chips:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=PA5 dir_pin=PA4 invert_step=0 step_pulse_ticks=32
|
|
config_stepper oid=1 step_pin=PA3 dir_pin=PA2 invert_step=0 step_pulse_ticks=32
|
|
config_stepper oid=2 step_pin=PC7 dir_pin=PC6 invert_step=0 step_pulse_ticks=32
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version `avr-gcc
|
|
(GCC) 5.4.0`. Both the 16Mhz and 20Mhz tests were run using simulavr
|
|
configured for an atmega644p (previous tests have confirmed simulavr
|
|
results match tests on both a 16Mhz at90usb and a 16Mhz atmega2560).
|
|
|
|
| avr | ticks |
|
|
| ---------------- | ----- |
|
|
| 1 stepper | 102 |
|
|
| 3 stepper | 486 |
|
|
|
|
### Arduino Due step rate benchmark
|
|
|
|
The following configuration sequence is used on the Due:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=PB27 dir_pin=PA21 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=PB26 dir_pin=PC30 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=PA21 dir_pin=PC30 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0`.
|
|
|
|
| sam3x8e | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 66 |
|
|
| 3 stepper | 257 |
|
|
|
|
### Duet Maestro step rate benchmark
|
|
|
|
The following configuration sequence is used on the Duet Maestro:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=PC26 dir_pin=PC18 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=PC26 dir_pin=PA8 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=PC26 dir_pin=PB4 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0`.
|
|
|
|
| sam4s8c | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 71 |
|
|
| 3 stepper | 260 |
|
|
|
|
### Duet Wifi step rate benchmark
|
|
|
|
The following configuration sequence is used on the Duet Wifi:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=PD6 dir_pin=PD11 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=PD7 dir_pin=PD12 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=PD8 dir_pin=PD13 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`gcc version 10.3.1 20210621 (release) (GNU Arm Embedded Toolchain 10.3-2021.07)`.
|
|
|
|
| sam4e8e | ticks |
|
|
| ---------------- | ----- |
|
|
| 1 stepper | 48 |
|
|
| 3 stepper | 215 |
|
|
|
|
### Beaglebone PRU step rate benchmark
|
|
|
|
The following configuration sequence is used on the PRU:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=gpio0_23 dir_pin=gpio1_12 invert_step=0 step_pulse_ticks=20
|
|
config_stepper oid=1 step_pin=gpio1_15 dir_pin=gpio0_26 invert_step=0 step_pulse_ticks=20
|
|
config_stepper oid=2 step_pin=gpio0_22 dir_pin=gpio2_1 invert_step=0 step_pulse_ticks=20
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version `pru-gcc
|
|
(GCC) 8.0.0 20170530 (experimental)`.
|
|
|
|
| pru | ticks |
|
|
| ---------------- | ----- |
|
|
| 1 stepper | 231 |
|
|
| 3 stepper | 847 |
|
|
|
|
### STM32F042 step rate benchmark
|
|
|
|
The following configuration sequence is used on the STM32F042:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=PA1 dir_pin=PA2 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=PA3 dir_pin=PA2 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=PB8 dir_pin=PA2 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0`.
|
|
|
|
| stm32f042 | ticks |
|
|
| ---------------- | ----- |
|
|
| 1 stepper | 59 |
|
|
| 3 stepper | 249 |
|
|
|
|
### STM32F103 step rate benchmark
|
|
|
|
The following configuration sequence is used on the STM32F103:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=PC13 dir_pin=PB5 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=PB3 dir_pin=PB6 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=PA4 dir_pin=PB7 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0`.
|
|
|
|
| stm32f103 | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 61 |
|
|
| 3 stepper | 264 |
|
|
|
|
### STM32F4 step rate benchmark
|
|
|
|
The following configuration sequence is used on the STM32F4:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=PA5 dir_pin=PB5 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=PB2 dir_pin=PB6 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=PB3 dir_pin=PB7 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0`. The STM32F407
|
|
results were obtained by running an STM32F407 binary on an STM32F446
|
|
(and thus using a 168Mhz clock).
|
|
|
|
| stm32f446 | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 46 |
|
|
| 3 stepper | 205 |
|
|
|
|
| stm32f407 | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 46 |
|
|
| 3 stepper | 205 |
|
|
|
|
### STM32G0B1 step rate benchmark
|
|
|
|
The following configuration sequence is used on the STM32G0B1:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=PB13 dir_pin=PB12 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=PB10 dir_pin=PB2 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=PB0 dir_pin=PC5 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `247cd753` with gcc version
|
|
`arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0`.
|
|
|
|
| stm32f042 | ticks |
|
|
| ---------------- | ----- |
|
|
| 1 stepper | 58 |
|
|
| 3 stepper | 243 |
|
|
|
|
### LPC176x step rate benchmark
|
|
|
|
The following configuration sequence is used on the LPC176x:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=P1.20 dir_pin=P1.18 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=P1.21 dir_pin=P1.18 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=P1.23 dir_pin=P1.18 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0`. The 120Mhz LPC1769
|
|
results were obtained by overclocking an LPC1768 to 120Mhz.
|
|
|
|
| lpc1768 | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 52 |
|
|
| 3 stepper | 222 |
|
|
|
|
| lpc1769 | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 51 |
|
|
| 3 stepper | 222 |
|
|
|
|
### SAMD21 step rate benchmark
|
|
|
|
The following configuration sequence is used on the SAMD21:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=PA27 dir_pin=PA20 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=PB3 dir_pin=PA21 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=PA17 dir_pin=PA21 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0` on a SAMD21G18
|
|
micro-controller.
|
|
|
|
| samd21 | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 70 |
|
|
| 3 stepper | 306 |
|
|
|
|
### SAMD51 step rate benchmark
|
|
|
|
The following configuration sequence is used on the SAMD51:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=PA22 dir_pin=PA20 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=PA22 dir_pin=PA21 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=PA22 dir_pin=PA19 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0` on a SAMD51J19A
|
|
micro-controller.
|
|
|
|
| samd51 | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 39 |
|
|
| 3 stepper | 191 |
|
|
| 1 stepper (200Mhz) | 39 |
|
|
| 3 stepper (200Mhz) | 181 |
|
|
|
|
### RP2040 step rate benchmark
|
|
|
|
The following configuration sequence is used on the RP2040:
|
|
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=gpio25 dir_pin=gpio3 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=1 step_pin=gpio26 dir_pin=gpio4 invert_step=-1 step_pulse_ticks=0
|
|
config_stepper oid=2 step_pin=gpio27 dir_pin=gpio5 invert_step=-1 step_pulse_ticks=0
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0` on a Raspberry Pi
|
|
Pico board.
|
|
|
|
| rp2040 | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 5 |
|
|
| 3 stepper | 22 |
|
|
|
|
### Linux MCU step rate benchmark
|
|
|
|
The following configuration sequence is used on a Raspberry Pi:
|
|
```
|
|
allocate_oids count=3
|
|
config_stepper oid=0 step_pin=gpio2 dir_pin=gpio3 invert_step=0 step_pulse_ticks=5
|
|
config_stepper oid=1 step_pin=gpio4 dir_pin=gpio5 invert_step=0 step_pulse_ticks=5
|
|
config_stepper oid=2 step_pin=gpio6 dir_pin=gpio17 invert_step=0 step_pulse_ticks=5
|
|
finalize_config crc=0
|
|
```
|
|
|
|
The test was last run on commit `59314d99` with gcc version
|
|
`gcc (Raspbian 8.3.0-6+rpi1) 8.3.0` on a Raspberry Pi 3 (revision
|
|
a02082). It was difficult to get stable results in this benchmark.
|
|
|
|
| Linux (RPi3) | ticks |
|
|
| -------------------- | ----- |
|
|
| 1 stepper | 160 |
|
|
| 3 stepper | 380 |
|
|
|
|
## Command dispatch benchmark
|
|
|
|
The command dispatch benchmark tests how many "dummy" commands the
|
|
micro-controller can process. It is primarily a test of the hardware
|
|
communication mechanism. The test is run using the console.py tool
|
|
(described in [Debugging.md](Debugging.md)). The following is
|
|
cut-and-paste into the console.py terminal window:
|
|
```
|
|
DELAY {clock + 2*freq} get_uptime
|
|
FLOOD 100000 0.0 debug_nop
|
|
get_uptime
|
|
```
|
|
|
|
When the test completes, determine the difference between the clocks
|
|
reported in the two "uptime" response messages. The total number of
|
|
commands per second is then `100000 * mcu_frequency / clock_diff`.
|
|
|
|
Note that this test may saturate the USB/CPU capacity of a Raspberry
|
|
Pi. If running on a Raspberry Pi, Beaglebone, or similar host computer
|
|
then increase the delay (eg, `DELAY {clock + 20*freq} get_uptime`).
|
|
Where applicable, the benchmarks below are with console.py running on
|
|
a desktop class machine with the device connected via a high-speed
|
|
hub.
|
|
|
|
| MCU | Rate | Build | Build compiler |
|
|
| ------------------- | ---- | -------- | ------------------- |
|
|
| stm32f042 (CAN) | 18K | c105adc8 | arm-none-eabi-gcc (GNU Tools 7-2018-q3-update) 7.3.1 |
|
|
| atmega2560 (serial) | 23K | b161a69e | avr-gcc (GCC) 4.8.1 |
|
|
| sam3x8e (serial) | 23K | b161a69e | arm-none-eabi-gcc (Fedora 7.1.0-5.fc27) 7.1.0 |
|
|
| at90usb1286 (USB) | 75K | 01d2183f | avr-gcc (GCC) 5.4.0 |
|
|
| samd21 (USB) | 223K | 01d2183f | arm-none-eabi-gcc (Fedora 7.4.0-1.fc30) 7.4.0 |
|
|
| pru (shared memory) | 260K | c5968a08 | pru-gcc (GCC) 8.0.0 20170530 (experimental) |
|
|
| stm32f103 (USB) | 355K | 01d2183f | arm-none-eabi-gcc (Fedora 7.4.0-1.fc30) 7.4.0 |
|
|
| sam3x8e (USB) | 418K | 01d2183f | arm-none-eabi-gcc (Fedora 7.4.0-1.fc30) 7.4.0 |
|
|
| lpc1768 (USB) | 534K | 01d2183f | arm-none-eabi-gcc (Fedora 7.4.0-1.fc30) 7.4.0 |
|
|
| lpc1769 (USB) | 628K | 01d2183f | arm-none-eabi-gcc (Fedora 7.4.0-1.fc30) 7.4.0 |
|
|
| sam4s8c (USB) | 650K | 8d4a5c16 | arm-none-eabi-gcc (Fedora 7.4.0-1.fc30) 7.4.0 |
|
|
| samd51 (USB) | 864K | 01d2183f | arm-none-eabi-gcc (Fedora 7.4.0-1.fc30) 7.4.0 |
|
|
| stm32f446 (USB) | 870K | 01d2183f | arm-none-eabi-gcc (Fedora 7.4.0-1.fc30) 7.4.0 |
|
|
| rp2040 (USB) | 873K | c5667193 | arm-none-eabi-gcc (Fedora 10.2.0-4.fc34) 10.2.0 |
|
|
|
|
## Host Benchmarks
|
|
|
|
It is possible to run timing tests on the host software using the
|
|
"batch mode" processing mechanism (described in
|
|
[Debugging.md](Debugging.md)). This is typically done by choosing a
|
|
large and complex G-Code file and timing how long it takes for the
|
|
host software to process it. For example:
|
|
```
|
|
time ~/klippy-env/bin/python ./klippy/klippy.py config/example-cartesian.cfg -i something_complex.gcode -o /dev/null -d out/klipper.dict
|
|
```
|