mirror of https://github.com/Desuuuu/klipper.git
185 lines
8.3 KiB
Markdown
185 lines
8.3 KiB
Markdown
This document describes the method for calibrating the x, y, and z
|
|
offsets of an "automatic z probe" in Klipper. This is useful for users
|
|
that have a `[probe]` or `[bltouch]` section in their config file.
|
|
|
|
# Calibrating probe X and Y offsets
|
|
|
|
To calibrate the X and Y offset, navigate to the OctoPrint "Control"
|
|
tab, home the printer, and then use the OctoPrint jogging buttons to
|
|
move the head to a position near the center of the bed.
|
|
|
|
Place a piece of blue painters tape (or similar) on the bed underneath
|
|
the probe. Navigate to the OctoPrint "Terminal" tab and issue a PROBE
|
|
command:
|
|
```
|
|
PROBE
|
|
```
|
|
Place a mark on the tape directly under where the probe is (or use a
|
|
similar method to note the location on the bed).
|
|
|
|
Issue a `GET_POSITION` command and record the toolhead XY location
|
|
reported by that command. For example if one sees:
|
|
```
|
|
Recv: // toolhead: X:46.500000 Y:27.000000 Z:15.000000 E:0.000000
|
|
```
|
|
then one would record a probe X position of 46.5 and probe Y position
|
|
of 27.
|
|
|
|
After recording the probe position, issue a series of G1 commands
|
|
until the nozzle is directly above the mark on the bed. For example,
|
|
one might issue:
|
|
```
|
|
G1 F300 X57 Y30 Z15
|
|
```
|
|
to move the nozzle to an X position of 57 and Y of 30. Once one finds
|
|
the position directly above the mark, use the `GET_POSITION` command
|
|
to report that position. This is the nozzle position.
|
|
|
|
The x_offset is then the `nozzle_x_position - probe_x_position` and
|
|
y_offset is similarly the `nozzle_y_position - probe_y_position`.
|
|
Update the printer.cfg file with the given values, remove the
|
|
tape/marks from the bed, and then issue a `RESTART` command so that
|
|
the new values take effect.
|
|
|
|
# Calibrating probe Z offset
|
|
|
|
Providing an accurate probe z_offset is critical to obtaining high
|
|
quality prints. The z_offset is the distance between the nozzle and
|
|
bed when the probe triggers. The Klipper `PROBE_CALIBRATE` tool can be
|
|
used to obtain this value - it will run an automatic probe to measure
|
|
the probe's Z trigger position and then start a manual probe to obtain
|
|
the nozzle Z height. The probe z_offset will then be calculated from
|
|
these measurements.
|
|
|
|
Start by homing the printer and then move the head to a position near
|
|
the center of the bed. Navigate to the OctoPrint terminal tab and run
|
|
the `PROBE_CALIBRATE` command to start the tool.
|
|
|
|
This tool will perform an automatic probe, then lift the head, move
|
|
the nozzle over the location of the probe point, and start the manual
|
|
probe tool. If the nozzle does not move to a position above the
|
|
automatic probe point, then `ABORT` the manual probe tool and perform
|
|
the XY probe offset calibration described above.
|
|
|
|
Once the manual probe tool starts, follow the steps described at
|
|
["the paper test"](Bed_Level.md#the-paper-test)) to determine the
|
|
actual distance between the nozzle and bed at the given location. Once
|
|
those steps are complete one can `ACCEPT` the position and save the
|
|
results to the config file with:
|
|
```
|
|
SAVE_CONFIG
|
|
```
|
|
|
|
# Repeatability check
|
|
|
|
After calibrating the probe X, Y, and Z offsets it is a good idea to
|
|
verify that the probe provides repeatable results. Start by homing the
|
|
printer and then move the head to a position near the center of the
|
|
bed. Navigate to the OctoPrint terminal tab and run the
|
|
`PROBE_ACCURACY` command.
|
|
|
|
This command will run the probe ten times and produce output similar
|
|
to the following:
|
|
```
|
|
Recv: // probe accuracy: at X:0.000 Y:0.000 Z:10.000
|
|
Recv: // and read 10 times with speed of 5 mm/s
|
|
Recv: // probe at -0.003,0.005 is z=2.506948
|
|
Recv: // probe at -0.003,0.005 is z=2.519448
|
|
Recv: // probe at -0.003,0.005 is z=2.519448
|
|
Recv: // probe at -0.003,0.005 is z=2.506948
|
|
Recv: // probe at -0.003,0.005 is z=2.519448
|
|
Recv: // probe at -0.003,0.005 is z=2.519448
|
|
Recv: // probe at -0.003,0.005 is z=2.506948
|
|
Recv: // probe at -0.003,0.005 is z=2.506948
|
|
Recv: // probe at -0.003,0.005 is z=2.519448
|
|
Recv: // probe at -0.003,0.005 is z=2.506948
|
|
Recv: // probe accuracy results: maximum 2.506948, minimum 2.519448, average 2.513198, median 2.513198, standard deviation 0.006250
|
|
```
|
|
|
|
Ideally the tool will report an identical maximum and minimum value.
|
|
(That is, ideally the probe obtains an identical result on all ten
|
|
probes.) However, it's normal for the minimum/maximum distance to
|
|
differ by one Z step_distance or up to 5 microns (.005mm). So, in the
|
|
above example, since the printer uses a Z step_distance of .0125, the
|
|
results would be considered normal.
|
|
|
|
If the results of the test show a minimum and maximum distance that
|
|
differs by more than 25 microns (.025mm) then the probe does not have
|
|
sufficient accuracy for typical bed leveling procedures. It may be
|
|
possible to tune the probe speed and/or probe start height to improve
|
|
the repeatability of the probe. The `PROBE_ACCURACY` command allows
|
|
one to run tests with different parameters to see their impact - see
|
|
the [G-Codes document](G-Codes.md) for further details. If the probe
|
|
generally obtains repeatable results but has an occasional outlier,
|
|
then it may be possible to account for that by using multiple samples
|
|
on each probe - read the description of the probe `samples` config
|
|
parameters in the
|
|
[example-extras.cfg](https://github.com/KevinOConnor/klipper/tree/master/config/example-extras.cfg)
|
|
file for more details.
|
|
|
|
If new probe speed, samples count, or other settings are needed, then
|
|
update the printer.cfg file and issue a `RESTART` command. If so, it
|
|
is a good idea to
|
|
[calibrate the z_offset](#calibrating-probe-z-offset) again. If
|
|
repeatable results can not be obtained then don't use the probe for
|
|
bed leveling. Klipper has several manual probing tools that can be
|
|
used instead - see the [Bed Level document](Bed_Level.md) for further
|
|
details.
|
|
|
|
# Location Bias Check
|
|
|
|
Some probes can have a systemic bias that corrupts the results of the
|
|
probe at certain toolhead locations. For example, if the probe mount
|
|
tilts slightly when moving along the Y axis then it could result in
|
|
the probe reporting biased results at different Y positions.
|
|
|
|
This is a common issue with probes on delta printers, however it can
|
|
occur on all printers.
|
|
|
|
One can check for a location bias by using the `PROBE_CALIBRATE`
|
|
command to measuring the probe z_offset at various X and Y
|
|
locations. Ideally, the probe z_offset would be a constant value at
|
|
every printer location.
|
|
|
|
For delta printers, try measuring the z_offset at a position near the
|
|
A tower, at a position near the B tower, and at a position near the C
|
|
tower. For cartesian, corexy, and similar printers, try measuring the
|
|
z_offset at positions near the four corners of the bed.
|
|
|
|
Before starting this test, first calibrate the probe X, Y, and Z
|
|
offsets as described at the beginning of this document. Then home the
|
|
printer and navigate to the first XY position. Follow the steps at
|
|
[calibrating probe Z offset](#calibrating-probe-z-offset) to run the
|
|
`PROBE_CALIBRATE` command, `TESTZ` commands, and `ACCEPT` command, but
|
|
do not run `SAVE_CONFIG`. Note the reported z_offset found. Then
|
|
navigate to the other XY positions, repeat these `PROBE_CALIBRATE`
|
|
steps, and note the reported z_offset.
|
|
|
|
If the difference between the minimum reported z_offset and the
|
|
maximum reported z_offset is greater than 25 microns (.025mm) then the
|
|
probe is not suitable for typical bed leveling procedures. See the
|
|
[Bed Level document](Bed_Level.md) for manual probe alternatives.
|
|
|
|
# Temperature Bias
|
|
|
|
Many probes have a systemic bias when probing at different
|
|
temperatures. For example, the probe may consistently trigger at a
|
|
lower height when the probe is at a higher temperature.
|
|
|
|
It is recommended to run the bed leveling tools at a consistent
|
|
temperature to account for this bias. For example, either always run
|
|
the tools when the printer is at room temperature, or always run the
|
|
tools after the printer has obtained a consistent print temperature.
|
|
In either case, it is a good idea to wait several minutes after the
|
|
desired temperature is reached, so that the printer apparatus is
|
|
consistently at the desired temperature.
|
|
|
|
To check for a temperature bias, start with the printer at room
|
|
temperature and then home the printer, move the head to a position
|
|
near the center of the bed, and run the `PROBE_ACCURACY` command. Note
|
|
the results. Then, without homing or disabling the stepper motors,
|
|
heat the printer nozzle and bed to printing temperature, and run the
|
|
`PROBE_ACCURACY` command again. Ideally, the command will report
|
|
identical results. As above, if the probe does have a temperature bias
|
|
then be careful to always use the probe at a consistent temperature.
|