mirror of https://github.com/Desuuuu/klipper.git
115 lines
5.3 KiB
Markdown
115 lines
5.3 KiB
Markdown
This document provides information on tuning the "pressure advance"
|
|
configuration variable for a particular nozzle and filament. The
|
|
pressure advance feature can be helpful in reducing ooze. For more
|
|
information on how pressure advance is implemented see the
|
|
[kinematics](Kinematics.md) document.
|
|
|
|
Tuning pressure advance
|
|
=======================
|
|
|
|
Pressure advance does two useful things - it reduces ooze during
|
|
non-extrude moves and it reduces blobbing during cornering. This guide
|
|
uses the second feature (reducing blobbing during cornering) as a
|
|
mechanism for tuning.
|
|
|
|
In order to calibrate pressure advance the printer must be configured
|
|
and operational. The tuning test involves printing objects and
|
|
inspecting the differences between objects. It is a good idea to read
|
|
this document in full prior to running the test.
|
|
|
|
Use a slicer to generate g-code for the large hollow square found in
|
|
[docs/prints/square.stl](prints/square.stl). Use a high speed (eg,
|
|
100mm/s) and a coarse layer height (the layer height should be around
|
|
75% of the nozzle diameter). It is fine to use a low infill (eg, 10%).
|
|
|
|
Use a low cornering speed during the test by issuing the following
|
|
G-Code command: `SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=0
|
|
ACCEL=500`. This will make the nozzle travel slower through corners
|
|
and thus emphasize the effects of extruder pressure.
|
|
|
|
For the first print use a pressure advance of zero by running
|
|
`SET_PRESSURE_ADVANCE ADVANCE=0.000`. Then print at least 10 layers of
|
|
the test object. While the object is printing, make a note of which
|
|
direction the head is moving during external perimeters. What many
|
|
people see here is blobbing occurring at the corners - extra filament
|
|
at the corner in the direction the head travels followed by a possible
|
|
lack of filament on the side immediately after that corner:
|
|
|
|
|
|
|
|
This blobbing is the result of pressure in the extruder being released
|
|
as a blob when the head slows down to corner.
|
|
|
|
The next step is to increase pressure advance (start with
|
|
`SET_PRESSURE_ADVANCE ADVANCE=0.050`) and reprint the test object.
|
|
With pressure advance, the extruder will retract when the head slows
|
|
down, thus countering the pressure buildup and ideally eliminate the
|
|
blobbing.
|
|
|
|
If a test run is done with a pressure advance setting that is too
|
|
high, one typically sees a dimple in the corner followed by possible
|
|
blobbing after the corner (too much filament is retracted during slow
|
|
down and then too much filament is extruded during the following speed
|
|
up after cornering):
|
|
|
|
|
|
|
|
The goal is to find the smallest pressure advance value that results
|
|
in good quality corners:
|
|
|
|
|
|
|
|
Typical pressure advance values are between 0.050 and 1.000 (the high
|
|
end usually only with bowden extruders). If there is no significant
|
|
improvement after gradually increasing pressure advance to 1.000, then
|
|
pressure advance is unlikely to improve the quality of prints. Return
|
|
to a default configuration with pressure advance disabled.
|
|
|
|
Although this tuning exercise directly improves the quality of
|
|
corners, it's worth remembering that a good pressure advance
|
|
configuration also reduces ooze throughout the print.
|
|
|
|
At the completion of this test, update the extruder's pressure_advance
|
|
setting in the configuration file and issue a RESTART command. The
|
|
RESTART command will also return the acceleration and cornering speeds
|
|
to their normal values.
|
|
|
|
Important Notes
|
|
===============
|
|
|
|
* The pressure advance value is dependent on the extruder, the nozzle,
|
|
and the filament. It is common for filament from different
|
|
manufactures or with different pigments to require significantly
|
|
different pressure advance values. Therefore, one should calibrate
|
|
pressure advance on each printer and with each spool of filament.
|
|
|
|
* Printing temperature and extrusion rates can impact pressure
|
|
advance. Be sure to tune the extruder
|
|
[E steps](http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide#E_steps)
|
|
and
|
|
[nozzle temperature](http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide#Nozzle_Temperature)
|
|
prior to tuning pressure advance.
|
|
|
|
* It is not unusual for one corner of the test print to be
|
|
consistently different than the other three corners. This typically
|
|
occurs when the slicer arranges to always change Z height at that
|
|
corner. If this occurs, then ignore that corner and tune pressure
|
|
advance using the other three corners.
|
|
|
|
* If a high pressure advance value (eg, over 0.200) is used then one
|
|
may find that the extruder skips when returning to the printer's
|
|
normal acceleration. The pressure advance system accounts for
|
|
pressure by pushing in extra filament during acceleration and
|
|
retracting that filament during deceleration. With a high
|
|
acceleration and high pressure advance the extruder may not have
|
|
enough torque to push the required filament. If this occurs, either
|
|
use a lower acceleration value or disable pressure advance.
|
|
|
|
* Once pressure advance is tuned in Klipper, it may still be useful to
|
|
configure a small retract value in the slicer (eg, 0.75mm) and to
|
|
utilize the slicer's "wipe on retract option" if available. These
|
|
slicer settings may help counteract ooze caused by filament cohesion
|
|
(filament pulled out of the nozzle due to the stickiness of the
|
|
plastic). It is recommended to disable the slicer's "z-lift on
|
|
retract" option.
|