mirror of https://github.com/Desuuuu/klipper.git
431 lines
20 KiB
Markdown
431 lines
20 KiB
Markdown
Frequently asked questions
|
|
==========================
|
|
|
|
1. [How can I donate to the project?](#how-can-i-donate-to-the-project)
|
|
2. [How do I calculate the step_distance parameter in the printer config file?](#how-do-i-calculate-the-step_distance-parameter-in-the-printer-config-file)
|
|
3. [Where's my serial port?](#wheres-my-serial-port)
|
|
4. [When the micro-controller restarts the device changes to /dev/ttyUSB1](#when-the-micro-controller-restarts-the-device-changes-to-devttyusb1)
|
|
5. [The "make flash" command doesn't work](#the-make-flash-command-doesnt-work)
|
|
6. [How do I change the serial baud rate?](#how-do-i-change-the-serial-baud-rate)
|
|
7. [Can I run Klipper on something other than a Raspberry Pi 3?](#can-i-run-klipper-on-something-other-than-a-raspberry-pi-3)
|
|
8. [Can I run multiple instances of Klipper on the same host machine?](#can-i-run-multiple-instances-of-klipper-on-the-same-host-machine)
|
|
9. [Why can't I move the stepper before homing the printer?](#why-cant-i-move-the-stepper-before-homing-the-printer)
|
|
10. [Why is the Z position_endstop set to 0.5 in the default configs?](#why-is-the-z-position_endstop-set-to-05-in-the-default-configs)
|
|
11. [I converted my config from Marlin and the X/Y axes work fine, but I just get a screeching noise when homing the Z axis](#i-converted-my-config-from-marlin-and-the-xy-axes-work-fine-but-i-just-get-a-screeching-noise-when-homing-the-z-axis)
|
|
12. [My TMC motor driver turns off in the middle of a print](#my-tmc-motor-driver-turns-off-in-the-middle-of-a-print)
|
|
13. [I keep getting random "Lost communication with MCU" errors](#i-keep-getting-random-lost-communication-with-mcu-errors)
|
|
14. [My Raspberry Pi keeps rebooting during prints](#my-raspberry-pi-keeps-rebooting-during-prints)
|
|
15. [When I set "restart_method=command" my AVR device just hangs on a restart](#when-i-set-restart_methodcommand-my-avr-device-just-hangs-on-a-restart)
|
|
16. [Will the heaters be left on if the Raspberry Pi crashes?](#will-the-heaters-be-left-on-if-the-raspberry-pi-crashes)
|
|
17. [How do I convert a Marlin pin number to a Klipper pin name?](#how-do-i-convert-a-marlin-pin-number-to-a-klipper-pin-name)
|
|
18. [How do I cancel an M109/M190 "wait for temperature" request?](#how-do-i-cancel-an-m109m190-wait-for-temperature-request)
|
|
19. [How do I upgrade to the latest software?](#how-do-i-upgrade-to-the-latest-software)
|
|
|
|
### How can I donate to the project?
|
|
|
|
Thanks. Kevin has a Patreon page at: https://www.patreon.com/koconnor
|
|
|
|
### How do I calculate the step_distance parameter in the printer config file?
|
|
|
|
If you know the steps per millimeter for the axis then use a
|
|
calculator to divide 1.0 by steps_per_mm. Then round this number to
|
|
six decimal places and place it in the config (six decimal places is
|
|
nano-meter precision).
|
|
|
|
The step_distance defines the distance that the axis will travel on
|
|
each motor driver pulse. It can also be calculated from the axis
|
|
pitch, motor step angle, and driver microstepping. If unsure, do a web
|
|
search for "calculate steps per mm" to find an online calculator.
|
|
|
|
### Where's my serial port?
|
|
|
|
The general way to find a USB serial port is to run `ls -l
|
|
/dev/serial/by-id/` from an ssh terminal on the host machine. It will
|
|
likely produce output similar to the following:
|
|
```
|
|
lrwxrwxrwx 1 root root 13 Jun 1 21:12 usb-1a86_USB2.0-Serial-if00-port0 -> ../../ttyUSB0
|
|
```
|
|
|
|
The name found in the above command is stable and it is possible to
|
|
use it in the config file and while flashing the micro-controller
|
|
code. For example, a flash command might look similar to:
|
|
```
|
|
sudo service klipper stop
|
|
make flash FLASH_DEVICE=/dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
sudo service klipper start
|
|
```
|
|
and the updated config might look like:
|
|
```
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
```
|
|
|
|
Be sure to copy-and-paste the name from the "ls" command that you ran
|
|
above as the name will be different for each printer.
|
|
|
|
If you are using multiple micro-controllers and they do not have
|
|
unique ids (common on boards with a CH340 USB chip) then follow the
|
|
directions above using the directory `/dev/serial/by-path/` instead.
|
|
|
|
### When the micro-controller restarts the device changes to /dev/ttyUSB1
|
|
|
|
Follow the directions in the
|
|
"[Where's my serial port?](#wheres-my-serial-port)" section to prevent
|
|
this from occurring.
|
|
|
|
### The "make flash" command doesn't work
|
|
|
|
The code attempts to flash the device using the most common method for
|
|
each platform. Unfortunately, there is a lot of variance in flashing
|
|
methods, so the "make flash" command may not work on all boards.
|
|
|
|
If you're having an intermittent failure or you do have a standard
|
|
setup, then double check that Klipper isn't running when flashing
|
|
(sudo service klipper stop), make sure OctoPrint isn't trying to
|
|
connect directly to the device (open the Connection tab in the web
|
|
page and click Disconnect if the Serial Port is set to the device),
|
|
and make sure FLASH_DEVICE is set correctly for your board (see the
|
|
[question above](#wheres-my-serial-port)).
|
|
|
|
However, if "make flash" just doesn't work for your board, then you
|
|
will need to manually flash. See if there is a config file in the
|
|
[config directory](../config) with specific instructions for flashing
|
|
the device. Also, check the board manufacturer's documentation to see
|
|
if it describes how to flash the device. Finally, on AVR devices, it
|
|
may be possible to manually flash the device using
|
|
[avrdude](http://www.nongnu.org/avrdude/) with custom command-line
|
|
parameters - see the avrdude documentation for further information.
|
|
|
|
### How do I change the serial baud rate?
|
|
|
|
The recommended baud rate for Klipper is 250000. This baud rate works
|
|
well on all micro-controller boards that Klipper supports. If you've
|
|
found an online guide recommending a different baud rate, then ignore
|
|
that part of the guide and continue with the default value of 250000.
|
|
|
|
If you want to change the baud rate anyway, then the new rate will
|
|
need to be configured in the micro-controller (during **make
|
|
menuconfig**) and that updated code will need to be compiled and
|
|
flashed to the micro-controller. The Klipper printer.cfg file will
|
|
also need to be updated to match that baud rate (see the example.cfg
|
|
file for details). For example:
|
|
```
|
|
[mcu]
|
|
baud: 250000
|
|
```
|
|
|
|
The baud rate shown on the OctoPrint web page has no impact on the
|
|
internal Klipper micro-controller baud rate. Always set the OctoPrint
|
|
baud rate to 250000 when using Klipper.
|
|
|
|
The Klipper micro-controller baud rate is not related to the baud rate
|
|
of the micro-controller's bootloader. See the
|
|
[bootloader document](Bootloaders.md) for additional information on
|
|
bootloaders.
|
|
|
|
### Can I run Klipper on something other than a Raspberry Pi 3?
|
|
|
|
The recommended hardware is a Raspberry Pi 2 or a Raspberry
|
|
Pi 3.
|
|
|
|
Klipper will run on a Raspberry Pi 1 and on the Raspberry Pi Zero, but
|
|
these boards don't have enough processing power to run OctoPrint
|
|
well. It's not uncommon for print stalls to occur on these slower
|
|
machines (the printer may move faster than OctoPrint can send movement
|
|
commands) when printing directly from OctoPrint. If you wish to run on
|
|
one one of these slower boards anyway, consider using the
|
|
"virtual_sdcard" feature (see
|
|
[config/example-extras.cfg](../config/example-extras.cfg) for details)
|
|
when printing.
|
|
|
|
For running on the Beaglebone, see the
|
|
[Beaglebone specific installation instructions](beaglebone.md).
|
|
|
|
Klipper has been run on other machines. The Klipper host software
|
|
only requires Python running on a Linux (or similar)
|
|
computer. However, if you wish to run it on a different machine you
|
|
will need Linux admin knowledge to install the system prerequisites
|
|
for that particular machine. See the
|
|
[install-octopi.sh](../scripts/install-octopi.sh) script for further
|
|
information on the necessary Linux admin steps.
|
|
|
|
### Can I run multiple instances of Klipper on the same host machine?
|
|
|
|
It is possible to run multiple instances of the Klipper host software,
|
|
but doing so requires Linux admin knowledge. The Klipper installation
|
|
scripts ultimately cause the following Unix command to be run:
|
|
```
|
|
~/klippy-env/bin/python ~/klipper/klippy/klippy.py ~/printer.cfg -l /tmp/klippy.log
|
|
```
|
|
One can run multiple instances of the above command as long as each
|
|
instance has its own printer config file and its own log file.
|
|
|
|
If you choose to do this, you will need to implement the necessary
|
|
start, stop, and installation scripts (if any). The
|
|
[install-octopi.sh](../scripts/install-octopi.sh) script and the
|
|
[klipper-start.sh](../scripts/klipper-start.sh) script may be useful
|
|
as examples.
|
|
|
|
### Why can't I move the stepper before homing the printer?
|
|
|
|
The code does this to reduce the chance of accidentally commanding the
|
|
head into the bed or a wall. Once the printer is homed the software
|
|
attempts to verify each move is within the position_min/max defined in
|
|
the config file. If the motors are disabled (via an M84 or M18
|
|
command) then the motors will need to be homed again prior to
|
|
movement.
|
|
|
|
If you want to move the head after canceling a print via OctoPrint,
|
|
consider changing the OctoPrint cancel sequence to do that for
|
|
you. It's configured in OctoPrint via a web browser under:
|
|
Settings->GCODE Scripts
|
|
|
|
If you want to move the head after a print finishes, consider adding
|
|
the desired movement to the "custom g-code" section of your slicer.
|
|
|
|
If the printer requires some additional movement as part of the homing
|
|
process itself (or fundamentally does not have a homing process) then
|
|
consider using a homing_override section in the config file. If you
|
|
need to move a stepper for diagnostic or debugging purposes then
|
|
consider adding a force_move section to the config file. See
|
|
[example-extras.cfg](../config/example-extras.cfg) for further details
|
|
on these options.
|
|
|
|
### Why is the Z position_endstop set to 0.5 in the default configs?
|
|
|
|
For cartesian style printers the Z position_endstop specifies how far
|
|
the nozzle is from the bed when the endstop triggers. If possible, it
|
|
is recommended to use a Z-max endstop and home away from the bed (as
|
|
this reduces the potential for bed collisions). However, if one must
|
|
home towards the bed then it is recommended to position the endstop so
|
|
it triggers when the nozzle is still a small distance away from the
|
|
bed. This way, when homing the axis, it will stop before the nozzle
|
|
touches the bed.
|
|
|
|
Almost all mechanical switches can still move a small distance
|
|
(eg, 0.5mm) after they are triggered. So, for example, if the
|
|
position_endstop is set to 0.5mm then one may still command the
|
|
printer to move to Z0.2. The position_min config setting (which
|
|
defaults to 0) is used to specify the minimum Z position one may
|
|
command the printer to move to.
|
|
|
|
Note, the Z position_endstop specifies the distance from the nozzle to
|
|
the bed when the nozzle and bed (if applicable) are hot. It is typical
|
|
for thermal expansion to cause nozzle expansion of around .1mm, which
|
|
is also the typical thickness of a sheet of printer paper. Thus, it is
|
|
common to use the "paper test" to confirm calibration of the Z
|
|
height - check that the bed and nozzle are at room temperature, check
|
|
that there is no plastic on the head or bed, home the printer, place a
|
|
piece of paper between the nozzle and bed, and repeatedly command the
|
|
head to move closer to the bed checking each time if you feel a small
|
|
amount of friction when sliding the paper between bed and nozzle - if
|
|
all is calibrated well a small amount of friction would be felt when
|
|
the height is at Z0.
|
|
|
|
### I converted my config from Marlin and the X/Y axes work fine, but I just get a screeching noise when homing the Z axis
|
|
|
|
Short answer: Try reducing the max_z_velocity setting in the printer
|
|
config. Also, if the Z stepper is moving in the wrong direction, try
|
|
inverting the dir_pin setting in the config (eg, "dir_pin: !xyz"
|
|
instead of "dir_pin: xyz").
|
|
|
|
Long answer: In practice Marlin can typically only step at a rate of
|
|
around 10000 steps per second. If it is requested to move at a speed
|
|
that would require a higher step rate then Marlin will generally just
|
|
step as fast as it can. Klipper is able to achieve much higher step
|
|
rates, but the stepper motor may not have sufficient torque to move at
|
|
a higher speed. So, for a Z axis with a very precise step_distance the
|
|
actual obtainable max_z_velocity may be smaller than what is
|
|
configured in Marlin.
|
|
|
|
### My TMC motor driver turns off in the middle of a print
|
|
|
|
There have been reports of some TMC drivers being disabled in the
|
|
middle of a print. (In particular, with the TMC2208 driver.) When this
|
|
issue occurs, the stepper associated with the driver moves freely,
|
|
while the print continues.
|
|
|
|
It is believed this may be due to "over current" detection within the
|
|
TMC driver. Trinamic has indicated that this could occur if the driver
|
|
is in "stealthChop mode" and an abrupt velocity change occurs. If you
|
|
experience this problem during homing, consider using a slower homing
|
|
speed. If you experience this problem in the middle of a print,
|
|
consider using a lower square_corner_velocity setting.
|
|
|
|
### I keep getting random "Lost communication with MCU" errors
|
|
|
|
This is commonly caused by hardware errors on the USB connection
|
|
between the host machine and the micro-controller. Things to look for:
|
|
- Use a good quality USB cable between the host machine and
|
|
micro-controller. Make sure the plugs are secure.
|
|
- If using a Raspberry Pi, use a
|
|
[good quality power supply](https://www.raspberrypi.org/documentation/hardware/raspberrypi/power/README.md)
|
|
for the Raspberry Pi and use a
|
|
[good quality USB cable](https://www.raspberrypi.org/forums/viewtopic.php?p=589877#p589877)
|
|
to connect that power supply to the Pi. If you get "under voltage"
|
|
warnings from OctoPrint, this is related to the power supply and it
|
|
must be fixed.
|
|
- Make sure the printer's power supply is not being overloaded. (Power
|
|
fluctuations to the micro-controller's USB chip may result in resets
|
|
of that chip.)
|
|
- Verify stepper, heater, and other printer wires are not crimped or
|
|
frayed. (Printer movement may place stress on a faulty wire causing
|
|
it to lose contact, briefly short, or generate excessive noise.)
|
|
- There have been reports of high USB noise when both the printer's
|
|
power supply and the host's 5V power supply are mixed. (If you find
|
|
that the micro-controller powers on when either the printer's power
|
|
supply is on or the USB cable is plugged in, then it indicates the
|
|
5V power supplies are being mixed.) It may help to configure the
|
|
micro-controller to use power from only one source. (Alternatively,
|
|
if the micro-controller board can not configure its power source,
|
|
one may modify a USB cable so that it does not carry 5V power
|
|
between the host and micro-controller.)
|
|
|
|
### My Raspberry Pi keeps rebooting during prints
|
|
|
|
This is most likely do to voltage fluctuations. Follow the same
|
|
troubleshooting steps for a
|
|
["Lost communication with MCU"](#i-keep-getting-random-lost-communication-with-mcu-errors)
|
|
error.
|
|
|
|
### When I set "restart_method=command" my AVR device just hangs on a restart
|
|
|
|
Some old versions of the AVR bootloader have a known bug in watchdog
|
|
event handling. This typically manifests when the printer.cfg file has
|
|
restart_method set to "command". When the bug occurs, the AVR device
|
|
will be unresponsive until power is removed and reapplied to the
|
|
device (the power or status LEDs may also blink repeatedly until the
|
|
power is removed).
|
|
|
|
The workaround is to use a restart_method other than "command" or to
|
|
flash an updated bootloader to the AVR device. Flashing a new
|
|
bootloader is a one time step that typically requires an external
|
|
programmer - search the web to find the instructions for your
|
|
particular device.
|
|
|
|
### Will the heaters be left on if the Raspberry Pi crashes?
|
|
|
|
The software has been designed to prevent that. Once the host enables
|
|
a heater, the host software needs to confirm that enablement every 5
|
|
seconds. If the micro-controller does not receive a confirmation every
|
|
5 seconds it goes into a "shutdown" state which is designed to turn
|
|
off all heaters and stepper motors.
|
|
|
|
See the "config_digital_out" command in the
|
|
[MCU commands](MCU_Commands.md) document for further details.
|
|
|
|
In addition, the micro-controller software is configured with a
|
|
minimum and maximum temperature range for each heater at startup (see
|
|
the min_temp and max_temp parameters in the
|
|
[example.cfg](../config/example.cfg) file for details). If the
|
|
micro-controller detects that the temperature is outside of that range
|
|
then it will also enter a "shutdown" state.
|
|
|
|
Separately, the host software also implements code to check that
|
|
heaters and temperature sensors are functioning correctly. See the
|
|
"verify_heater" section of the
|
|
[example-extras.cfg](../config/example-extras.cfg) for further
|
|
details.
|
|
|
|
### How do I convert a Marlin pin number to a Klipper pin name?
|
|
|
|
Short answer: In some cases one can use Klipper's `pin_map: arduino`
|
|
feature. Otherwise, for "digital" pins, one method is to search for
|
|
the requested pin in Marlin's fastio header files. The Atmega2560 and
|
|
Atmega1280 chips use
|
|
[fastio_1280.h](https://github.com/MarlinFirmware/Marlin/blob/1.1.9/Marlin/fastio_1280.h),
|
|
while the Atmega644p and Atmega1284p chips use
|
|
[fastio_644.h](https://github.com/MarlinFirmware/Marlin/blob/1.1.9/Marlin/fastio_644.h).
|
|
For example, if you are looking to translate Marlin's digital pin
|
|
number 23 on an atmega2560 then one could find the following line in
|
|
Marlin's fastio_1280.h file:
|
|
```
|
|
#define DIO23_PIN PINA1
|
|
```
|
|
The `DIO23` indicates the line is for Marlin's pin 23 and the `PINA1`
|
|
indicates the pin uses the hardware name of `PA1`. Klipper uses the
|
|
hardware names (eg, `PA1`).
|
|
|
|
Long answer: Klipper uses the standard pin names defined by the
|
|
micro-controller. On the Atmega chips these hardware pins have names
|
|
like `PA4`, `PC7`, or `PD2`.
|
|
|
|
Long ago, the Arduino project decided to avoid using the standard
|
|
hardware names in favor of their own pin names based on incrementing
|
|
numbers - these Arduino names generally look like `D23` or `A14`. This
|
|
was an unfortunate choice that has lead to a great deal of confusion.
|
|
In particular the Arduino pin numbers frequently don't translate to
|
|
the same hardware names. For example, `D21` is `PD0` on one common
|
|
Arduino board, but is `PC7` on another common Arduino board.
|
|
|
|
In order to support 3d printers based on real Arduino boards, Klipper
|
|
supports the Arduino pin aliases. This feature is enabled by adding
|
|
`pin_map: arduino` to the [mcu] section of the config file. When these
|
|
aliases are enabled, Klipper understands pin names that start with the
|
|
prefix "ar" (eg, Arduino pin `D23` is Klipper alias `ar23`) and the
|
|
prefix "analog" (eg, Arduino pin `A14` is Klipper alias `analog14`).
|
|
Klipper does not use the Arduino names directly because we feel a name
|
|
like D7 is too easily confused with the hardware name PD7.
|
|
|
|
Marlin primarily follows the Arduino pin numbering scheme. However,
|
|
Marlin supports a few chips that Arduino does not support and in some
|
|
cases it supports pins that Arduino boards do not expose. In these
|
|
cases, Marlin chose their own pin numbering scheme. Klipper does not
|
|
support these custom pin numbers - check Marlin's fastio headers (see
|
|
above) to translate these pin numbers to their standard hardware
|
|
names.
|
|
|
|
### How do I cancel an M109/M190 "wait for temperature" request?
|
|
|
|
Navigate to the OctoPrint terminal tab and issue an M112 command in
|
|
the terminal box. The M112 command will cause Klipper to enter into a
|
|
"shutdown" state, and it will cause OctoPrint to disconnect from
|
|
Klipper. Navigate to the OctoPrint connection area and click on
|
|
"Connect" to cause OctoPrint to reconnect. Navigate back to the
|
|
terminal tab and issue a FIRMWARE_RESTART command to clear the Klipper
|
|
error state. After completing this sequence, the previous heating
|
|
request will be canceled and a new print may be started.
|
|
|
|
### How do I upgrade to the latest software?
|
|
|
|
The general way to upgrade is to ssh into the Raspberry Pi and run:
|
|
|
|
```
|
|
cd ~/klipper
|
|
git pull
|
|
~/klipper/scripts/install-octopi.sh
|
|
```
|
|
|
|
Then one can recompile and flash the micro-controller code. For
|
|
example:
|
|
|
|
```
|
|
make menuconfig
|
|
make clean
|
|
make
|
|
|
|
sudo service klipper stop
|
|
make flash FLASH_DEVICE=/dev/ttyACM0
|
|
sudo service klipper start
|
|
```
|
|
|
|
However, it's often the case that only the host software changes. In
|
|
this case, one can update and restart just the host software with:
|
|
|
|
```
|
|
cd ~/klipper
|
|
git pull
|
|
sudo service klipper restart
|
|
```
|
|
|
|
If after using this shortcut the software warns about needing to
|
|
reflash the micro-controller or some other unusual error occurs, then
|
|
follow the full upgrade steps outlined above. Note that the RESTART
|
|
and FIRMWARE_RESTART g-code commands do not load new software - the
|
|
above "sudo service klipper restart" and "make flash" commands are
|
|
needed for a software change to take effect.
|
|
|
|
When upgrading the software, be sure to check the
|
|
[config changes](Config_Changes.md) document for information on
|
|
software changes that may require updates to your printer.cfg file.
|