mirror of https://github.com/Desuuuu/klipper.git
303 lines
16 KiB
Markdown
303 lines
16 KiB
Markdown
This document provides information on the low-level micro-controller
|
|
commands that are sent from the Klipper "host" software and processed
|
|
by the Klipper micro-controller software. This document is not an
|
|
authoritative reference for these commands, nor is it an exclusive
|
|
list of all available commands.
|
|
|
|
This document may be useful for developers interested in understanding
|
|
the low-level micro-controller commands.
|
|
|
|
See the [protocol](Protocol.md) document for more information on the
|
|
format of commands and their transmission. The commands here are
|
|
described using their "printf" style syntax - for those unfamiliar
|
|
with that format, just note that where a '%...' sequence is seen it
|
|
should be replaced with an actual integer. For example, a description
|
|
with "count=%c" could be replaced with the text "count=10". Note that
|
|
parameters that are considered "enumerations" (see the above protocol
|
|
document) take a string value which is automatically converted to an
|
|
integer value for the micro-controller. This is common with parameters
|
|
named "pin" (or that have a suffix of "_pin").
|
|
|
|
Startup Commands
|
|
================
|
|
|
|
It may be necessary to take certain one-time actions to configure the
|
|
micro-controller and its peripherals. This section lists common
|
|
commands available for that purpose. Unlike most micro-controller
|
|
commands, these commands run as soon as they are received and they do
|
|
not require any particular setup.
|
|
|
|
Common startup commands:
|
|
|
|
* `set_digital_out pin=%u value=%c` : This command immediately
|
|
configures the given pin as a digital out GPIO and it sets it to
|
|
either a low level (value=0) or a high level (value=1). This command
|
|
may be useful for configuring the initial value of LEDs and for
|
|
configuring the initial value of stepper driver micro-stepping pins.
|
|
|
|
* `set_pwm_out pin=%u cycle_ticks=%u value=%hu` : This command will
|
|
immediately configure the given pin to use hardware based
|
|
pulse-width-modulation (PWM) with the given number of
|
|
cycle_ticks. The "cycle_ticks" is the number of MCU clock ticks each
|
|
power on and power off cycle should last. A cycle_ticks value of 1
|
|
can be used to request the fastest possible cycle time. The "value"
|
|
parameter is between 0 and 255 with 0 indicating a full off state
|
|
and 255 indicating a full on state. This command may be useful for
|
|
enabling CPU and nozzle cooling fans.
|
|
|
|
Low-level micro-controller configuration
|
|
========================================
|
|
|
|
Most commands in the micro-controller require an initial setup before
|
|
they can be successfully invoked. This section provides an overview of
|
|
the configuration process. This section and the following sections are
|
|
likely only of interest to developers interested in the internal
|
|
details of Klipper.
|
|
|
|
When the host first connects to the micro-controller it always starts
|
|
by obtaining a data dictionary (see [protocol](Protocol.md) for more
|
|
information). After the data dictionary is obtained the host will
|
|
check if the micro-controller is in a "configured" state and configure
|
|
it if not. Configuration involves the following phases:
|
|
|
|
* `get_config` : The host starts by checking if the micro-controller
|
|
is already configured. The micro-controller responds to this command
|
|
with a "config" response message. The micro-controller software
|
|
always starts in an unconfigured state at power-on. It remains in
|
|
this state until the host completes the configuration processes (by
|
|
issuing a finalize_config command). If the micro-controller is
|
|
already configured from a previous session (and is configured with
|
|
the desired settings) then no further action is needed by the host
|
|
and the configuration process ends successfully.
|
|
|
|
* `allocate_oids count=%c` : This command is issued to inform the
|
|
micro-controller of the maximum number of object-ids (oid) that the
|
|
host requires. It is only valid to issue this command once. An oid
|
|
is an integer identifier allocated to each stepper, each endstop,
|
|
and each schedulable gpio pin. The host determines in advance the
|
|
number of oids it will require to operate the hardware and passes
|
|
this to the micro-controller so that it may allocate sufficient
|
|
memory to store a mapping from oid to internal object.
|
|
|
|
* `config_XXX oid=%c ...` : By convention any command starting with
|
|
the "config_" prefix creates a new micro-controller object and
|
|
assigns the given oid to it. For example, the config_digital_out
|
|
command will configure the specified pin as a digital output GPIO
|
|
and create an internal object that the host can use to schedule
|
|
changes to the given GPIO. The oid parameter passed into the config
|
|
command is selected by the host and must be between zero and the
|
|
maximum count supplied in the allocate_oids command. The config
|
|
commands may only be run when the micro-controller is not in a
|
|
configured state (ie, prior to the host sending finalize_config) and
|
|
after the allocate_oids command has been sent.
|
|
|
|
* `finalize_config crc=%u` : The finalize_config command transitions
|
|
the micro-controller from an unconfigured state to a configured
|
|
state. The crc parameter passed to the micro-controller is stored
|
|
and provided back to the host in "config" response messages. By
|
|
convention, the host takes a 32bit CRC of the configuration it will
|
|
request and at the start of subsequent communication sessions it
|
|
checks that the CRC stored in the micro-controller exactly matches
|
|
its desired CRC. If the CRC does not match then the host knows the
|
|
micro-controller has not been configured in the state desired by the
|
|
host.
|
|
|
|
Common micro-controller objects
|
|
-------------------------------
|
|
|
|
This section lists some commonly used config commands.
|
|
|
|
* `config_digital_out oid=%c pin=%u value=%c default_value=%c
|
|
max_duration=%u` : This command creates an internal micro-controller
|
|
object for the given GPIO 'pin'. The pin will be configured in
|
|
digital output mode and set to an initial value as specified by
|
|
'value' (0 for low, 1 for high). Creating a digital_out object
|
|
allows the host to schedule GPIO updates for the given pin at
|
|
specified times (see the schedule_digital_out command described
|
|
below). Should the micro-controller software go into shutdown mode
|
|
then all configured digital_out objects will be set to
|
|
'default_value'. The 'max_duration' parameter is used to implement a
|
|
safety check - if it is non-zero then it is the maximum number of
|
|
clock ticks that the host may set the given GPIO to a non-default
|
|
value without further updates. For example, if the default_value is
|
|
zero and the max_duration is 16000 then if the host sets the gpio to
|
|
a value of one then it must schedule another update to the gpio pin
|
|
(to either zero or one) within 16000 clock ticks. This safety
|
|
feature can be used with heater pins to ensure the host does not
|
|
enable the heater and then go off-line.
|
|
|
|
* `config_pwm_out oid=%c pin=%u cycle_ticks=%u value=%hu
|
|
default_value=%hu max_duration=%u` : This command creates an
|
|
internal object for hardware based PWM pins that the host may
|
|
schedule updates for. Its usage is analogous to config_digital_out -
|
|
see the description of the 'set_pwm_out' and 'config_digital_out'
|
|
commands for parameter description.
|
|
|
|
* `config_soft_pwm_out oid=%c pin=%u cycle_ticks=%u value=%c
|
|
default_value=%c max_duration=%u` : This command creates an internal
|
|
micro-controller object for software implemented PWM. Unlike
|
|
hardware pwm pins, a software pwm object does not require any
|
|
special hardware support (other than the ability to configure the
|
|
pin as a digital output GPIO). Because the output switching is
|
|
implemented in the micro-controller software, it is recommended that
|
|
the cycle_ticks parameter correspond to a time of 10ms or
|
|
greater. See the description of the 'set_pwm_out' and
|
|
'config_digital_out' commands for parameter description.
|
|
|
|
* `config_analog_in oid=%c pin=%u` : This command is used to configure
|
|
a pin in analog input sampling mode. Once configured, the pin can be
|
|
sampled at regular interval using the query_analog_in command (see
|
|
below).
|
|
|
|
* `config_stepper oid=%c step_pin=%c dir_pin=%c min_stop_interval=%u
|
|
invert_step=%c` : This command creates an internal stepper
|
|
object. The 'step_pin' and 'dir_pin' parameters specify the step and
|
|
direction pins respectively; this command will configure them in
|
|
digital output mode. The 'invert_step' parameter specifies whether a
|
|
step occurs on a rising edge (invert_step=0) or falling edge
|
|
(invert_step=1). The 'min_stop_interval' implements a safety
|
|
feature - it is checked when the micro-controller finishes all moves
|
|
for a stepper - if it is non-zero it specifies the minimum number of
|
|
clock ticks since the last step. It is used as a check on the
|
|
maximum stepper velocity that a stepper may have before stopping.
|
|
|
|
* `config_end_stop oid=%c pin=%c pull_up=%c stepper_count=%c` : This
|
|
command creates an internal "endstop" object. It is used to specify
|
|
the endstop pins and to enable "homing" operations (see the
|
|
end_stop_home command below). The command will configure the
|
|
specified pin in digital input mode. The 'pull_up' parameter
|
|
determines whether hardware provided pullup resistors for the pin
|
|
(if available) will be enabled. The 'stepper_count' parameter
|
|
specifies the maximum number of steppers that this endstop may need
|
|
to halt during a homing operation (see end_stop_home below).
|
|
|
|
* `config_spi oid=%c bus=%u pin=%u mode=%u rate=%u shutdown_msg=%*s` :
|
|
This command creates an internal SPI object. It is used with
|
|
spi_transfer and spi_send commands (see below). The "bus"
|
|
identifies the SPI bus to use (if the micro-controller has more than
|
|
one SPI bus available). The "pin" specifies the chip select (CS) pin
|
|
for the device. The "mode" is the SPI mode (should be between 0 and
|
|
3). The "rate" parameter specifies the SPI bus rate (in cycles per
|
|
second). Finally, the "shutdown_msg" is an SPI command to send to
|
|
the given device should the micro-controller go into a shutdown
|
|
state.
|
|
|
|
* `config_spi_without_cs oid=%c bus=%u mode=%u rate=%u
|
|
shutdown_msg=%*s` : This command is similar to config_spi, but
|
|
without a CS pin definition. It is useful for SPI devices that do
|
|
not have a chip select line.
|
|
|
|
Common commands
|
|
===============
|
|
|
|
This section lists some commonly used run-time commands. It is likely
|
|
only of interest to developers looking to gain insight into Klipper.
|
|
|
|
* `schedule_digital_out oid=%c clock=%u value=%c` : This command will
|
|
schedule a change to a digital output GPIO pin at the given clock
|
|
time. To use this command a 'config_digital_out' command with the
|
|
same 'oid' parameter must have been issued during micro-controller
|
|
configuration.
|
|
|
|
* `schedule_pwm_out oid=%c clock=%u value=%hu` : Schedules a change to
|
|
a hardware PWM output pin. See the 'schedule_digital_out' and
|
|
'config_pwm_out' commands for more info.
|
|
|
|
* `schedule_soft_pwm_out oid=%c clock=%u value=%hu` : Schedules a
|
|
change to a software PWM output pin. See the 'schedule_digital_out'
|
|
and 'config_soft_pwm_out' commands for more info.
|
|
|
|
* `query_analog_in oid=%c clock=%u sample_ticks=%u sample_count=%c
|
|
rest_ticks=%u min_value=%hu max_value=%hu` : This command sets up a
|
|
recurring schedule of analog input samples. To use this command a
|
|
'config_analog_in' command with the same 'oid' parameter must have
|
|
been issued during micro-controller configuration. The samples will
|
|
start as of 'clock' time, it will report on the obtained value every
|
|
'rest_ticks' clock ticks, it will over-sample 'sample_count' number
|
|
of times, and it will pause 'sample_ticks' number of clock ticks
|
|
between over-sample samples. The 'min_value' and 'max_value'
|
|
parameters implement a safety feature - the micro-controller
|
|
software will verify the sampled value (after any oversampling) is
|
|
always between the supplied range. This is intended for use with
|
|
pins attached to thermistors controlling heaters - it can be used to
|
|
check that a heater is within a temperature range.
|
|
|
|
* `get_clock` : This command causes the micro-controller to generate a
|
|
"clock" response message. The host sends this command once a second
|
|
to obtain the value of the micro-controller clock and to estimate
|
|
the drift between host and micro-controller clocks. It enables the
|
|
host to accurately estimate the micro-controller clock.
|
|
|
|
Stepper commands
|
|
----------------
|
|
|
|
* `queue_step oid=%c interval=%u count=%hu add=%hi` : This command
|
|
schedules 'count' number of steps for the given stepper, with
|
|
'interval' number of clock ticks between each step. The first step
|
|
will be 'interval' number of clock ticks since the last scheduled
|
|
step for the given stepper. If 'add' is non-zero then the interval
|
|
will be adjusted by 'add' amount after each step. This command
|
|
appends the given interval/count/add sequence to a per-stepper
|
|
queue. There may be hundreds of these sequences queued during normal
|
|
operation. New sequence are appended to the end of the queue and as
|
|
each sequence completes its 'count' number of steps it is popped
|
|
from the front of the queue. This system allows the micro-controller
|
|
to queue potentially hundreds of thousands of steps - all with
|
|
reliable and predictable schedule times.
|
|
|
|
* `set_next_step_dir oid=%c dir=%c` : This command specifies the value
|
|
of the dir_pin that the next queue_step command will use.
|
|
|
|
* `reset_step_clock oid=%c clock=%u` : Normally, step timing is
|
|
relative to the last step for a given stepper. This command resets
|
|
the clock so that the next step is relative to the supplied 'clock'
|
|
time. The host usually only sends this command at the start of a
|
|
print.
|
|
|
|
* `stepper_get_position oid=%c` : This command causes the
|
|
micro-controller to generate a "stepper_position" response message
|
|
with the stepper's current position. The position is the total
|
|
number of steps generated with dir=1 minus the total number of steps
|
|
generated with dir=0.
|
|
|
|
* `end_stop_home oid=%c clock=%u sample_ticks=%u sample_count=%c
|
|
rest_ticks=%u pin_value=%c` : This command is used during stepper
|
|
"homing" operations. To use this command a 'config_end_stop' command
|
|
with the same 'oid' parameter must have been issued during
|
|
micro-controller configuration. When this command is invoked, the
|
|
micro-controller will sample the endstop pin every 'rest_ticks'
|
|
clock ticks and check if it has a value equal to 'pin_value'. If the
|
|
value matches (and it continues to match for 'sample_count'
|
|
additional samples spread 'sample_ticks' apart) then the movement
|
|
queue for the associated stepper will be cleared and the stepper
|
|
will come to an immediate halt. The host uses this command to
|
|
implement homing - the host instructs the endstop to sample for the
|
|
endstop trigger and then it issues a series of queue_step commands
|
|
to move a stepper towards the endstop. Once the stepper hits the
|
|
endstop, the trigger will be detected, the movement halted, and the
|
|
host notified.
|
|
|
|
### Move queue
|
|
|
|
Each queue_step command utilizes an entry in the micro-controller
|
|
"move queue". This queue is allocated when it receives the
|
|
"finalize_config" command, and it reports the number of available
|
|
queue entries in "config" response messages.
|
|
|
|
It is the responsibility of the host to ensure that there is available
|
|
space in the queue before sending a queue_step command. The host does
|
|
this by calculating when each queue_step command completes and
|
|
scheduling new queue_step commands accordingly.
|
|
|
|
SPI Commands
|
|
------------
|
|
|
|
* `spi_transfer oid=%c data=%*s` : This command causes the
|
|
micro-controller to send 'data' to the spi device specified by 'oid'
|
|
and it generates a "spi_transfer_response" response message with the
|
|
data returned during the transmission.
|
|
|
|
* `spi_send oid=%c data=%*s` : This command is similar to
|
|
"spi_transfer", but it does not generate a "spi_transfer_response"
|
|
message.
|