mirror of https://github.com/Desuuuu/klipper.git
126 lines
6.1 KiB
Markdown
126 lines
6.1 KiB
Markdown
This document describes Klipper's stepper phase adjusted endstop
|
|
system. This functionality can improve the accuracy of traditional
|
|
endstop switches. It is most useful when using a Trinamic stepper
|
|
motor driver that has run-time configuration.
|
|
|
|
A typical endstop switch has an accuracy of around 100 microns. (Each
|
|
time an axis is homed the switch may trigger slightly earlier or
|
|
slightly later.) Although this is a relatively small error, it can
|
|
result in unwanted artifacts. In particular, this positional deviation
|
|
may be noticeable when printing the first layer of an object. In
|
|
contrast, typical stepper motors can obtain significantly higher
|
|
precision.
|
|
|
|
The stepper phase adjusted endstop mechanism can use the precision of
|
|
the stepper motors to improve the precision of the endstop switches.
|
|
A stepper motor moves by cycling through a series of phases until in
|
|
completes four "full steps". So, a stepper motor using 16 micro-steps
|
|
would have 64 phases and when moving in a positive direction it would
|
|
cycle through phases: 0, 1, 2, ... 61, 62, 63, 0, 1, 2, etc.
|
|
Crucially, when the stepper motor is at a particular position on a
|
|
linear rail it should always be at the same stepper phase. Thus, when
|
|
a carriage triggers the endstop switch the stepper controlling that
|
|
carriage should always be at the same stepper motor phase. Klipper's
|
|
endstop phase system combines the stepper phase with the endstop
|
|
trigger to improve the accuracy of the endstop.
|
|
|
|
In order to use this functionality it is necessary to be able to
|
|
identify the phase of the stepper motor. If one is using Trinamic
|
|
TMC2130, TMC2208, TMC2224 or TMC2660 drivers in run-time configuration
|
|
mode (ie, not stand-alone mode) then Klipper can query the stepper
|
|
phase from the driver. (It is also possible to use this system on
|
|
traditional stepper drivers if one can reliably reset the stepper
|
|
drivers - see below for details.)
|
|
|
|
Calibrating endstop phases
|
|
==========================
|
|
|
|
If using Trinamic stepper motor drivers with run-time configuration
|
|
then one can calibrate the endstop phases using the
|
|
ENDSTOP_PHASE_CALIBRATE command. Start by adding the following to the
|
|
config file:
|
|
```
|
|
[endstop_phase]
|
|
```
|
|
|
|
Then RESTART the printer and run a `G28` command followed by an
|
|
`ENDSTOP_PHASE_CALIBRATE` command. Then move the toolhead to a new
|
|
location and run `G28` again. Try moving the toolhead to several
|
|
different locations and rerun `G28` from each position. Run at least
|
|
five `G28` commands.
|
|
|
|
After performing the above, the `ENDSTOP_PHASE_CALIBRATE` command will
|
|
often report the same (or nearly the same) phase for the stepper. This
|
|
phase can be saved in the config file so that all future G28 commands
|
|
use that phase. (So, in future homing operations, Klipper will obtain
|
|
the same position even if the endstop triggers a little earlier or a
|
|
little later.)
|
|
|
|
To save the endstop phase for a particular stepper motor, run
|
|
something like the following:
|
|
```
|
|
ENDSTOP_PHASE_CALIBRATE STEPPER=stepper_z
|
|
```
|
|
|
|
Run the above for all the steppers one wishes to save. Typically, one
|
|
would use this on stepper_z for cartesian and corexy printers, and for
|
|
stepper_a, stepper_b, and stepper_c on delta printers. Finally, run
|
|
the following to update the configuration file with the data:
|
|
```
|
|
SAVE_CONFIG
|
|
```
|
|
|
|
Additional notes
|
|
----------------
|
|
|
|
* This feature is most useful on delta printers and on the Z endstop
|
|
of cartesian/corexy printers. It is possible to use this feature on
|
|
the XY endstops of cartesian printers, but that isn't particularly
|
|
useful as a minor error in X/Y endstop position is unlikely to
|
|
impact print quality. It is not valid to use this feature on the XY
|
|
endstops of corexy printers (as the XY position is not determined by
|
|
a single stepper on corexy kinematics). It is not valid to use this
|
|
feature on a printer using a "probe:z_virtual_endstop" Z endstop (as
|
|
the stepper phase is only stable if the endstop is at a static
|
|
location on a rail).
|
|
|
|
* After calibrating the endstop phase, if the endstop is later moved
|
|
or adjusted then it will be necessary to recalibrate the endstop.
|
|
Remove the calibration data from the config file and rerun the steps
|
|
above.
|
|
|
|
* In order to use this system the endstop must be accurate enough to
|
|
identify the stepper position within two "full steps". So, for
|
|
example, if a stepper is using 16 micro-steps with a step distance
|
|
of 0.005mm then the endstop must have an accuracy of at least
|
|
0.160mm. If one gets "Endstop stepper_z incorrect phase" type error
|
|
messages than in may be due to an endstop that is not sufficiently
|
|
accurate. If recalibration does not help then disable endstop phase
|
|
adjustments by removing them from the config file.
|
|
|
|
* If one is using a traditional stepper controlled Z axis (as on a
|
|
cartesian or corexy printer) along with traditional bed leveling
|
|
screws then it is also possible to use this system to arrange for
|
|
each print layer to be performed on a "full step" boundary. To
|
|
enable this feature be sure the G-Code slicer is configured with a
|
|
layer height that is a multiple of a "full step", manually enable
|
|
the endstop_align_zero option in the endstop_phase config section
|
|
(see config/example-extras.cfg for further details), and then
|
|
re-level the bed screws.
|
|
|
|
* It is possible to use this system with traditional (non-Trinamic)
|
|
stepper motor drivers. However, doing this requires making sure that
|
|
the stepper motor drivers are reset every time the micro-controller
|
|
is reset. (If the two are always reset together then Klipper can
|
|
determine the stepper phase by tracking the total number of steps it
|
|
has commanded the stepper to move.) Currently, the only way to do
|
|
this reliably is if both the micro-controller and stepper motor
|
|
drivers are powered solely from USB and that USB power is provided
|
|
from a host running on a Raspberry Pi. In this situation one can
|
|
specify an mcu config with "restart_method: rpi_usb" - that option
|
|
will arrange for the micro-controller to always be reset via a USB
|
|
power reset, which would arrange for both the micro-controller and
|
|
stepper motor drivers to be reset together. If using this mechanism,
|
|
one would then need to manually configure the "endstop_phase" config
|
|
sections (see config/example-extras.cfg for the details).
|