mirror of https://github.com/Desuuuu/klipper.git
137 lines
4.3 KiB
Markdown
137 lines
4.3 KiB
Markdown
Klipper is currently in an experimental state. These instructions
|
|
assume the software will run on a Raspberry Pi computer in conjunction
|
|
with OctoPrint. Klipper supports only Atmel ATmega based
|
|
micro-controllers and Arduino Due (Atmel SAM3x8e ARM
|
|
micro-controllers) printers at this time.
|
|
|
|
It is recommended that a Raspberry Pi 2 or Raspberry Pi 3 computer be
|
|
used as the host. The software will run on a first generation
|
|
Raspberry Pi, but the combined load of OctoPrint, Klipper, and a web
|
|
cam (if applicable) can overwhelm its CPU leading to print stalls.
|
|
|
|
Prepping an OS image
|
|
====================
|
|
|
|
Start by installing [OctoPi](https://github.com/guysoft/OctoPi) on the
|
|
Raspberry Pi computer. Use version 0.13.0 or later - see the
|
|
[octopi releases](https://github.com/guysoft/OctoPi/releases) for
|
|
release information. One should verify that OctoPi boots, that the
|
|
OctoPrint web server works, and that one can ssh to the octopi server
|
|
(ssh pi@octopi -- password is "raspberry") before continuing.
|
|
|
|
After installing OctoPi, ssh into the target machine and run the
|
|
following commands:
|
|
|
|
```
|
|
sudo apt-get update
|
|
sudo apt-get install libncurses-dev
|
|
sudo apt-get install avrdude gcc-avr binutils-avr avr-libc # AVR toolchain
|
|
sudo apt-get install bossa-cli libnewlib-arm-none-eabi # ARM toolchain
|
|
```
|
|
|
|
The host software (Klippy) requires a one-time setup - run as the
|
|
regular "pi" user:
|
|
|
|
```
|
|
virtualenv ~/klippy-env
|
|
~/klippy-env/bin/pip install cffi==1.6.0 pyserial==2.7
|
|
```
|
|
|
|
Building Klipper
|
|
================
|
|
|
|
To obtain Klipper, run the following command on the target machine:
|
|
|
|
```
|
|
git clone https://github.com/KevinOConnor/klipper
|
|
cd klipper/
|
|
```
|
|
|
|
To compile the micro-controller code, start by configuring it:
|
|
|
|
```
|
|
make menuconfig
|
|
```
|
|
|
|
Select the appropriate micro-controller and serial baud rate. Once
|
|
configured, run:
|
|
|
|
```
|
|
make
|
|
```
|
|
|
|
Ignore any warnings you may see about "misspelled signal handler" (it
|
|
is due to a bug fixed in gcc v4.8.3).
|
|
|
|
Installing Klipper on an AVR micro-controller
|
|
---------------------------------------------
|
|
|
|
The avrdude package can be used to install the micro-controller code
|
|
on an AVR ATmega chip. The exact syntax of the avrdude command is
|
|
different for each micro-controller. The following is an example
|
|
command for atmega2560 chips:
|
|
|
|
```
|
|
example-only$ avrdude -C/etc/avrdude.conf -v -patmega2560 -cwiring -P/dev/ttyACM0 -b115200 -D -Uflash:w:/home/pi/klipper/out/klipper.elf.hex:i
|
|
```
|
|
|
|
Installing Klipper on an Arduino Due
|
|
------------------------------------
|
|
|
|
Klipper currently uses the Arduino Due USB programming port (it will
|
|
not work when connected to the application USB port). The programming
|
|
port is the USB port closest to the power supply. To flash Klipper to
|
|
the Due connect it to the host machine and run:
|
|
|
|
```
|
|
stty -F /dev/ttyACM0 1200
|
|
bossac -i -p ttyACM0 -R -e -w -v -b ~/klipper/out/klipper.bin
|
|
```
|
|
|
|
Setting up the printer configuration
|
|
====================================
|
|
|
|
It is necessary to configure the printer. This is done by modifying a
|
|
configuration file that resides on the host. Start by copying an
|
|
example configuration and editing it. For example:
|
|
|
|
```
|
|
cp ~/klipper/config/example.cfg ~/printer.cfg
|
|
nano printer.cfg
|
|
```
|
|
|
|
Make sure to look at and update each setting that is appropriate for
|
|
the hardware.
|
|
|
|
Configuring OctoPrint to use Klippy
|
|
===================================
|
|
|
|
The OctoPrint web server needs to be configured to communicate with
|
|
the Klippy host software. Using a web-browser, login to the OctoPrint
|
|
web page, and navigate to the Settings tab. Then configure the
|
|
following items:
|
|
|
|
Under "Serial Connection" in "Additional serial ports" add
|
|
"/tmp/printer". Then click "Save".
|
|
|
|
Enter the Settings tab again and under "Serial Connection" change the
|
|
"Serial Port" setting to "/tmp/printer". Change the Baudrate field to
|
|
250000 (this buad rate field is not related to the firmware baudrate
|
|
and may be safely left at 250000).
|
|
|
|
Under the "Features" tab, unselect "Enable SD support". Then click
|
|
"Save".
|
|
|
|
Running the host software
|
|
=========================
|
|
|
|
The host software is executed by running the following as the regular
|
|
"pi" user:
|
|
|
|
```
|
|
~/klippy-env/bin/python ~/klipper/klippy/klippy.py ~/printer.cfg -l /tmp/klippy.log < /dev/null > /tmp/klippy-errors.log 2>&1 &
|
|
```
|
|
|
|
Once Klippy is running, use a web-browser and navigate to the
|
|
OctoPrint web site. Click on "Connect" under the "Connection" tab.
|