4.9 KiB
Frequently asked questions
How do I calculate the step_distance parameter in the printer config file?
If you know the steps per millimeter for the axis then use a calculator to divide 1.0 by steps_per_mm. Then round this number to six decimal places and place it in the config (six decimal places is nano-meter precision).
The step_distance defines the distance that the axis will travel on each motor driver pulse. It can also be calculated from the axis pitch, motor step angle, and driver microstepping. If unsure, do a web search for "calculate steps per mm" to find an online calculator.
When I restart my micro-controller the device changes to /dev/ttyACM1
If the device sometimes changes from /dev/ttyACM0 to /dev/ttyACM1 then
ssh into the host computer and run: ls -l /dev/serial/by-id/
The name found in the above command is stable and it is possible to use it in the config file. For example, an updated config might look like:
[mcu]
serial: /dev/serial/by-id/usb-UltiMachine__ultimachine.com__RAMBo_12345678912345678912-if00
Be sure to copy-and-paste the name from the "ls" command above as the name will be different on each printer.
Can I run Klipper on something other than a Raspberry Pi?
Klipper only requires Python running on a Linux (or similar) computer. However, if you wish to run it on a different machine you will need Linux admin knowledge to install the system prerequisites for the Linux distribution running on that particular machine. See the install-octopi.sh script for further information on the necessary Linux admin steps.
Why can't I move the stepper before homing the printer?
The code does this to reduce the chance of accidentally commanding the head into the bed or a wall. Once the printer is homed the software attempts to verify each move is within the position_min/max defined in the config file. If the motors are disabled (via an M84 or M18 command) then the motors will need to be homed again prior to movement.
If you want to move the head after canceling a print via Octoprint, consider changing the Octoprint cancel sequence to do that for you. It's configured in Octoprint via a web browser under: Settings->GCODE Scripts
If you want to move the head after a print finishes, consider adding the desired movement to the "custom g-code" section of your slicer.
Why is the Z position_endstop set to 0.5 in the default configs?
For cartesian style printers the Z position_endstop specifies how far the nozzle is from the bed when the endstop triggers. If possible, it is recommended to use a Z-max endstop and home away from the bed (as this reduces the potential for bed collisions). However, if one must home towards the bed then it is recommended to position the endstop so it triggers when the nozzle is still a small distance away from the bed. This way, when homing the axis, it will stop before the nozzle touches the bed.
Almost all mechanical switches can still move a small distance (eg, 0.5mm) after they are triggered. So, for example, if the position_endstop is set to 0.5mm then one may still command the printer to move to Z0.2. The position_min config setting (which defaults to 0) is used to specify the minimum Z position one may command the printer to move to.
Note, the Z position_endstop specifies the distance from the nozzle to the bed when the nozzle and bed (if applicable) are hot. It is typical for thermal expansion to cause nozzle expansion of around .1mm, which is also the typical thickness of a sheet of printer paper. Thus, it is common to use the "paper test" to confirm calibration of the Z height - check that the bed and nozzle are at room temperature, check that there is no plastic on the head or bed, home the printer, place a piece of paper between the nozzle and bed, and repeatedly command the head to move closer to the bed checking each time if you feel a small amount of friction when sliding the paper between bed and nozzle - if all is calibrated well a small amount of friction would be felt when the height is at Z0.
I converted my config from Marlin and the X/Y axes work fine, but I just get a screeching noise when homing the Z axis
Short answer: Try reducing the max_z_velocity setting in the printer config. Also, if the Z stepper is moving in the wrong direction, try inverting the dir_pin setting in the config (eg, "dir_pin: !xyz" instead of "dir_pin: xyz").
Long answer: In practice Marlin can typically only step at a rate of around 10000 steps per second. If it is requested to move at a speed that would require a higher step rate then Marlin will generally just step as fast as it can. Klipper is able to achieve much higher step rates, but the stepper motor may not have sufficient torque to move at a higher speed. So, for a Z axis with a very precise step_distance the actual obtainable max_z_velocity may be smaller than what is configured in Marlin.