mirror of https://github.com/Desuuuu/klipper.git
68 lines
2.6 KiB
Markdown
68 lines
2.6 KiB
Markdown
This document describes the protocol Klipper uses to communicate over
|
|
[CAN bus](https://en.wikipedia.org/wiki/CAN_bus). See
|
|
[CANBUS.md](CANBUS.md) for information on configuring Klipper with CAN
|
|
bus.
|
|
|
|
# Micro-controller id assignment
|
|
|
|
Klipper uses only CAN 2.0A standard size CAN bus packets, which are
|
|
limited to 8 data bytes and an 11-bit CAN bus identifier. In order to
|
|
support efficient communication, each micro-controller is assigned at
|
|
run-time a unique 1-byte CAN bus nodeid (`canbus_nodeid`) for general
|
|
Klipper command and response traffic. Klipper command messages going
|
|
from host to micro-controller use the CAN bus id of `canbus_nodeid *
|
|
2 + 256`, while Klipper response messages from micro-controller to
|
|
host use `canbus_nodeid * 2 + 256 + 1`.
|
|
|
|
Each micro-controller has a factory assigned unique chip identifier
|
|
that is used during id assignment. This identifier can exceed the
|
|
length of one CAN packet, so a hash function is used to generate a
|
|
unique 6-byte id (`canbus_uuid`) from the factory id.
|
|
|
|
# Admin messages
|
|
|
|
Admin messages are used for id assignment. Admin messages sent from
|
|
host to micro-controller use the CAN bus id `0x3f0` and messages sent
|
|
from micro-controller to host use the CAN bus id `0x3f1`. All
|
|
micro-controllers listen to messages on id `0x3f0`; that id can be
|
|
thought of as a "broadcast address".
|
|
|
|
## CMD_QUERY_UNASSIGNED message
|
|
|
|
This command queries all micro-controllers that have not yet been
|
|
assigned a `canbus_nodeid`. Unassigned micro-controllers will respond
|
|
with a RESP_NEED_NODEID response message.
|
|
|
|
The CMD_QUERY_UNASSIGNED message format is:
|
|
`<1-byte message_id = 0x00>`
|
|
|
|
## CMD_SET_NODEID message
|
|
|
|
This command assigns a `canbus_nodeid` to the micro-controller with a
|
|
given `canbus_uuid`.
|
|
|
|
The CMD_SET_NODEID message format is:
|
|
`<1-byte message_id = 0x01><6-byte canbus_uuid><1-byte canbus_nodeid>`
|
|
|
|
## RESP_NEED_NODEID message
|
|
|
|
The RESP_NEED_NODEID message format is:
|
|
`<1-byte message_id = 0x20><6-byte canbus_uuid>`
|
|
|
|
# Data Packets
|
|
|
|
A micro-controller that has been assigned a nodeid via the
|
|
CMD_SET_NODEID command can send and receive data packets.
|
|
|
|
The packet data in messages using the node's receive CAN bus id
|
|
(`canbus_nodeid * 2 + 256`) are simply appended to a buffer, and when
|
|
a complete [mcu protocol message](Protocol.md) is found its contents
|
|
are parsed and processed. The data is treated as a byte stream - there
|
|
is no requirement for the start of a Klipper message block to align
|
|
with the start of a CAN bus packet.
|
|
|
|
Similarly, mcu protocol message responses are sent from
|
|
micro-controller to host by copying the message data into one or more
|
|
packets with the node's transmit CAN bus id (`canbus_nodeid * 2 +
|
|
256 + 1`).
|