mirror of https://github.com/Desuuuu/klipper.git
148 lines
6.7 KiB
Markdown
148 lines
6.7 KiB
Markdown
This document provides a list of steps to help confirm the pin
|
|
settings in the Klipper printer.cfg file. It is a good idea to run
|
|
through these steps after following the steps in the
|
|
[installation document](Installation.md).
|
|
|
|
During this guide, it may be necessary to make changes to the Klipper
|
|
config file. Be sure to issue a RESTART command after every change to
|
|
the config file to ensure that the change takes effect (type "restart"
|
|
in the Octoprint terminal tab and then click "Send"). It's also a good
|
|
idea to issue a STATUS command after every RESTART to verify that the
|
|
config file is successfully loaded.
|
|
|
|
### Verify temperature
|
|
|
|
Start by verifying that temperatures are being properly
|
|
reported. Navigate to the Octoprint temperature tab.
|
|
|
|
|
|
|
|
Verify that the temperature of the nozzle and bed (if applicable) are
|
|
present and not increasing. If it is increasing, remove power from the
|
|
printer. If the temperatures are not accurate, review the
|
|
"sensor_type" and "sensor_pin" settings for the nozzle and/or bed.
|
|
|
|
### Verify M112
|
|
|
|
Navigate to the Octoprint terminal tab and issue an M112 command in
|
|
the terminal box. This command requests Klipper to go into a
|
|
"shutdown" state. It will cause Octoprint to disconnect from Klipper -
|
|
navigate to the Connection area and click on "Connect" to cause
|
|
Octoprint to reconnect. Then navigate to the Octoprint temperature tab
|
|
and verify that temperatures continue to update and the temperatures
|
|
are not increasing. If temperatures are increasing, remove power from
|
|
the printer.
|
|
|
|
The M112 command causes Klipper to go into a "shutdown" state. To
|
|
clear this state, issue a FIRMWARE_RESTART command in the Octoprint
|
|
terminal tab.
|
|
|
|
### Verify heaters
|
|
|
|
Navigate to the Octoprint temperature tab and type in 50 followed by
|
|
enter in the "Tool" temperature box. The extruder temperature in the
|
|
graph should start to increase (within about 30 seconds or so). Then
|
|
go to the "Tool" temperature drop-down box and select "Off". After
|
|
several minutes the temperature should start to return to its initial
|
|
room temperature value. If the temperature does not increase then
|
|
verify the "heater_pin" setting in the config.
|
|
|
|
If the printer has a heated bed then perform the above test again with
|
|
the bed.
|
|
|
|
### Verify stepper motor enable pin
|
|
|
|
Verify that all of the printer axes can manually move freely (the
|
|
stepper motors are disabled). If not, issue an M84 command to disable
|
|
the motors. If any of the axes still can not move freely, then verify
|
|
the stepper "enable_pin" configuration for the given axis. On most
|
|
commodity stepper motor drivers, the motor enable pin is "active low"
|
|
and therefore the enable pin should have a "!" before the pin (for
|
|
example, "enable_pin: !ar38").
|
|
|
|
### Verify endstops
|
|
|
|
Manually move all the printer axes so that none of them are in contact
|
|
with an endstop. Send a QUERY_ENDSTOPS command via the Octoprint
|
|
terminal tab. It should respond with the current state of all of the
|
|
configured endstops and they should all report a state of "open". For
|
|
each of the endstops, rerun the QUERY_ENDSTOPS command while manually
|
|
triggering the endstop. The QUERY_ENDSTOPS command should report the
|
|
endstop as "TRIGGERED".
|
|
|
|
If the endstop appears inverted (it reports "open" when triggered and
|
|
vice-versa) then add a "!" to the pin definition (for example,
|
|
"endstop_pin: ^!ar3"), or remove the "!" if there is already one
|
|
present.
|
|
|
|
If the endstop does not change at all then it generally indicates that
|
|
the endstop is connected to a different pin. However, it may also
|
|
require a change to the pullup setting of the pin (the '^' at the
|
|
start of the endstop_pin name - most printers will use a pullup
|
|
resistor and the '^' should be present).
|
|
|
|
### Verify stepper motor direction
|
|
|
|
Make sure the printer.cfg file does not have "homing_speed" set for
|
|
any axis (or set it to a value of 5 or less).
|
|
|
|
On cartesian style printers, manually move the X axis to a midway
|
|
point, issue a G28X0 command, and verify that the X motor moves slowly
|
|
towards the endstop defined for that axis. If the motor moves in the
|
|
wrong direction issue an M112 command to abort the move. A wrong
|
|
direction generally indicates that the "dir_pin" for the axis needs to
|
|
be inverted. This is done by adding a '!' to the "dir_pin" in the
|
|
printer config file (or removing it if one is already there). For
|
|
example, change "dir_pin: xyz" to "dir_pin: !xyz". Then RESTART and
|
|
retest the axis. If the axis does not move at all, then verify the
|
|
"enable_pin" and "step_pin" settings for the axis. For cartesian style
|
|
printers, repeat the test for the Y and Z axis with G28Y0 and G28Z0.
|
|
|
|
For delta style printers, manually move all three carriages to a
|
|
midway point and then issue a G28 command. Verify all three motors
|
|
move simultaneously upwards. If not, issue an M112 command and follow
|
|
the troubleshooting steps in the preceding paragraph.
|
|
|
|
### Verify extruder motor
|
|
|
|
To test the extruder motor it will be necessary to heat the extruder
|
|
to a printing temperature. Navigate to the Octoprint temperature tab
|
|
and select a target temperature from the temperature drop-down box (or
|
|
manually enter an appropriate temperature). Wait for the printer to
|
|
reach the desired temperature. Then navigate to the Octoprint control
|
|
tab and click the "Extrude" button. Verify that the extruder motor
|
|
turns in the correct direction. If it does not, see the
|
|
troubleshooting tips in the previous section to confirm the
|
|
"enable_pin", "step_pin", and "dir_pin" settings for the extruder.
|
|
|
|
### Calibrate PID settings
|
|
|
|
Klipper supports
|
|
[PID control](https://en.wikipedia.org/wiki/PID_controller) for the
|
|
extruder and bed heaters. In order to use this control mechanism it is
|
|
necessary to calibrate the PID settings on each printer. (PID settings
|
|
found in other firmwares or in the example configuration files often
|
|
work poorly.)
|
|
|
|
To calibrate the extruder, navigate to the OctoPrint terminal tab and
|
|
run the PID_CALIBRATE command. For example: `PID_CALIBRATE
|
|
HEATER=extruder TARGET=170`
|
|
|
|
At the completion of the tuning test, update the printer.cfg file with
|
|
the recommended pid_Kp, pid_Ki, and pid_Kd values.
|
|
|
|
If the printer has a heated bed and it supports being driven by PWM
|
|
(Pulse Width Modulation) then it is recommended to use PID control for
|
|
the bed. (When the bed heater is controlled using the PID algorithm it
|
|
may turn on and off ten times a second, which may not be suitable for
|
|
heaters using a mechanical switch.) A typical bed PID calibration
|
|
command is: `PID_CALIBRATE HEATER=heater_bed TARGET=60`
|
|
|
|
### Next steps
|
|
|
|
This guide is intended to help with basic verification of pin settings
|
|
in the Klipper configuration file. It may be necessary to perform
|
|
detailed printer calibration - a number of guides are available online
|
|
to help with this (for example, do a web search for "3d printer
|
|
calibration").
|