mirror of https://github.com/Desuuuu/klipper.git
67 lines
2.6 KiB
Markdown
67 lines
2.6 KiB
Markdown
This document describes the method for calibrating the x, y, and z
|
|
offsets of an "automatic z probe" in Klipper. This is useful for users
|
|
that have a `[probe]` or `[bltouch]` section in their config file.
|
|
|
|
# Calibrating probe X and Y offsets
|
|
|
|
To calibrate the X and Y offset, navigate to the OctoPrint "Control"
|
|
tab, home the printer, and then use the OctoPrint jogging buttons to
|
|
move the head to a position near the center of the bed.
|
|
|
|
Place a piece of blue painters tape (or similar) on the bed underneath
|
|
the probe. Navigate to the OctoPrint "Terminal" tab and issue a PROBE
|
|
command:
|
|
```
|
|
PROBE
|
|
```
|
|
Place a mark on the tape directly under where the probe is (or use a
|
|
similar method to note the location on the bed).
|
|
|
|
Issue a `GET_POSITION` command and record the toolhead XY location
|
|
reported by that command. For example if one sees:
|
|
```
|
|
Recv: // toolhead: X:46.500000 Y:27.000000 Z:15.000000 E:0.000000
|
|
```
|
|
then one would record a probe X position of 46.5 and probe Y position
|
|
of 27.
|
|
|
|
After recording the probe position, issue a series of G1 commands
|
|
until the nozzle is directly above the mark on the bed. For example,
|
|
one might issue:
|
|
```
|
|
G1 F300 X57 Y30 Z15
|
|
```
|
|
to move the nozzle to an X position of 57 and Y of 30. Once one finds
|
|
the position directly above the mark, use the `GET_POSITION` command
|
|
to report that position. This is the nozzle position.
|
|
|
|
The x_offset is then the `nozzle_x_position - probe_x_position` and
|
|
y_offset is similarly the `nozzle_y_position - probe_y_position`.
|
|
Update the printer.cfg file with the given values, remove the
|
|
tape/marks from the bed, and then issue a `RESTART` command so that
|
|
the new values take effect.
|
|
|
|
# Calibrating probe Z offset
|
|
|
|
Providing an accurate probe Z offset is critical to obtaining high
|
|
quality prints.
|
|
|
|
Start by homing the printer and then move the head to a position near
|
|
the center of the bed. Navigate to the OctoPrint terminal tab and run
|
|
the `PROBE_CALIBRATE` command to start Klipper's probe calibration
|
|
tool.
|
|
|
|
This tool will perform an automatic probe, then lift the head, move
|
|
the nozzle over the location of the probe point, and start the manual
|
|
probe tool. Once the manual probe tool starts, perform the
|
|
["paper test"](Bed_Level.md#the-paper-test) to determine the actual
|
|
nozzle height at the given point.
|
|
|
|
If the nozzle does not move to a position above the probe point, then
|
|
`ABORT` the manual probe tool and perform the XY probe offset
|
|
calibration described above.
|
|
|
|
After completing the "paper test", use the `ACCEPT` command to
|
|
accept the current Z height and then use the `SAVE_CONFIG` command to
|
|
save the given probe z_offset to the config file.
|