mirror of https://github.com/Desuuuu/klipper.git
159 lines
7.3 KiB
Markdown
159 lines
7.3 KiB
Markdown
This document provides a list of steps to help confirm the pin
|
|
settings in the Klipper printer.cfg file. It is a good idea to run
|
|
through these steps after following the steps in the
|
|
[installation document](Installation.md).
|
|
|
|
During this guide, it may be necessary to make changes to the Klipper
|
|
config file. Be sure to issue a RESTART command after every change to
|
|
the config file to ensure that the change takes effect (type "restart"
|
|
in the Octoprint terminal tab and then click "Send"). It's also a good
|
|
idea to issue a STATUS command after every RESTART to verify that the
|
|
config file is successfully loaded.
|
|
|
|
### Verify temperature
|
|
|
|
Start by verifying that temperatures are being properly
|
|
reported. Navigate to the Octoprint temperature tab.
|
|
|
|
|
|
|
|
Verify that the temperature of the nozzle and bed (if applicable) are
|
|
present and not increasing. If it is increasing, remove power from the
|
|
printer. If the temperatures are not accurate, review the
|
|
"sensor_type" and "sensor_pin" settings for the nozzle and/or bed.
|
|
|
|
### Verify M112
|
|
|
|
Navigate to the Octoprint terminal tab and issue an M112 command in
|
|
the terminal box. This command requests Klipper to go into a
|
|
"shutdown" state. It will cause Octoprint to disconnect from Klipper -
|
|
navigate to the Connection area and click on "Connect" to cause
|
|
Octoprint to reconnect. Then navigate to the Octoprint temperature tab
|
|
and verify that temperatures continue to update and the temperatures
|
|
are not increasing. If temperatures are increasing, remove power from
|
|
the printer.
|
|
|
|
The M112 command causes Klipper to go into a "shutdown" state. To
|
|
clear this state, issue a FIRMWARE_RESTART command in the Octoprint
|
|
terminal tab.
|
|
|
|
### Verify heaters
|
|
|
|
Navigate to the Octoprint temperature tab and type in 50 followed by
|
|
enter in the "Tool" temperature box. The extruder temperature in the
|
|
graph should start to increase (within about 30 seconds or so). Then
|
|
go to the "Tool" temperature drop-down box and select "Off". After
|
|
several minutes the temperature should start to return to its initial
|
|
room temperature value. If the temperature does not increase then
|
|
verify the "heater_pin" setting in the config.
|
|
|
|
If the printer has a heated bed then perform the above test again with
|
|
the bed.
|
|
|
|
### Verify stepper motor enable pin
|
|
|
|
Verify that all of the printer axes can manually move freely (the
|
|
stepper motors are disabled). If not, issue an M84 command to disable
|
|
the motors. If any of the axes still can not move freely, then verify
|
|
the stepper "enable_pin" configuration for the given axis. On most
|
|
commodity stepper motor drivers, the motor enable pin is "active low"
|
|
and therefore the enable pin should have a "!" before the pin (for
|
|
example, "enable_pin: !ar38").
|
|
|
|
### Verify endstops
|
|
|
|
Manually move all the printer axes so that none of them are in contact
|
|
with an endstop. Send a QUERY_ENDSTOPS command via the Octoprint
|
|
terminal tab. It should respond with the current state of all of the
|
|
configured endstops and they should all report a state of "open". For
|
|
each of the endstops, rerun the QUERY_ENDSTOPS command while manually
|
|
triggering the endstop. The QUERY_ENDSTOPS command should report the
|
|
endstop as "TRIGGERED".
|
|
|
|
If the endstop appears inverted (it reports "open" when triggered and
|
|
vice-versa) then add a "!" to the pin definition (for example,
|
|
"endstop_pin: ^!ar3"), or remove the "!" if there is already one
|
|
present.
|
|
|
|
If the endstop does not change at all then it generally indicates that
|
|
the endstop is connected to a different pin. However, it may also
|
|
require a change to the pullup setting of the pin (the '^' at the
|
|
start of the endstop_pin name - most printers will use a pullup
|
|
resistor and the '^' should be present).
|
|
|
|
### Verify stepper motors
|
|
|
|
Use the STEPPER_BUZZ command to verify the connectivity of each
|
|
stepper motor. Start by manually positioning the given axis to a
|
|
midway point and then run `STEPPER_BUZZ STEPPER=stepper_x` . The
|
|
STEPPER_BUZZ command will cause the given stepper to move one
|
|
millimeter in a positive direction and then it will return to its
|
|
starting position. (If the endstop is defined at position_endstop=0
|
|
then at the start of each movement the stepper will move away from the
|
|
endstop.) It will perform this oscillation ten times.
|
|
|
|
If the stepper does not move at all, then verify the "enable_pin" and
|
|
"step_pin" settings for the stepper. If the stepper motor moves but
|
|
does not return to its original position then verify the "dir_pin"
|
|
setting. If the stepper motor oscillates in an incorrect direction,
|
|
then it generally indicates that the "dir_pin" for the axis needs to
|
|
be inverted. This is done by adding a '!' to the "dir_pin" in the
|
|
printer config file (or removing it if one is already there). If the
|
|
motor moves significantly more or significantly less than one
|
|
millimeter then verify the "step_distance" setting.
|
|
|
|
Run the above test for each stepper motor defined in the config
|
|
file. (Set the STEPPER parameter of the STEPPER_BUZZ command to the
|
|
name of the config section that is to be tested.) If there is no
|
|
filament in the extruder then one can use STEPPER_BUZZ to verify the
|
|
extruder motor connectivity (use STEPPER=extruder). Otherwise, it's
|
|
best to test the extruder motor separately (see the next section).
|
|
|
|
After verifying all endstops and verifying all stepper motors the
|
|
homing mechanism should be tested. Issue a G28 command to home all
|
|
axes. Remove power from the printer if it does not home properly.
|
|
Rerun the endstop and stepper motor verification steps if necessary.
|
|
|
|
### Verify extruder motor
|
|
|
|
To test the extruder motor it will be necessary to heat the extruder
|
|
to a printing temperature. Navigate to the Octoprint temperature tab
|
|
and select a target temperature from the temperature drop-down box (or
|
|
manually enter an appropriate temperature). Wait for the printer to
|
|
reach the desired temperature. Then navigate to the Octoprint control
|
|
tab and click the "Extrude" button. Verify that the extruder motor
|
|
turns in the correct direction. If it does not, see the
|
|
troubleshooting tips in the previous section to confirm the
|
|
"enable_pin", "step_pin", and "dir_pin" settings for the extruder.
|
|
|
|
### Calibrate PID settings
|
|
|
|
Klipper supports
|
|
[PID control](https://en.wikipedia.org/wiki/PID_controller) for the
|
|
extruder and bed heaters. In order to use this control mechanism it is
|
|
necessary to calibrate the PID settings on each printer. (PID settings
|
|
found in other firmwares or in the example configuration files often
|
|
work poorly.)
|
|
|
|
To calibrate the extruder, navigate to the OctoPrint terminal tab and
|
|
run the PID_CALIBRATE command. For example: `PID_CALIBRATE
|
|
HEATER=extruder TARGET=170`
|
|
|
|
At the completion of the tuning test, update the printer.cfg file with
|
|
the recommended pid_Kp, pid_Ki, and pid_Kd values.
|
|
|
|
If the printer has a heated bed and it supports being driven by PWM
|
|
(Pulse Width Modulation) then it is recommended to use PID control for
|
|
the bed. (When the bed heater is controlled using the PID algorithm it
|
|
may turn on and off ten times a second, which may not be suitable for
|
|
heaters using a mechanical switch.) A typical bed PID calibration
|
|
command is: `PID_CALIBRATE HEATER=heater_bed TARGET=60`
|
|
|
|
### Next steps
|
|
|
|
This guide is intended to help with basic verification of pin settings
|
|
in the Klipper configuration file. It may be necessary to perform
|
|
detailed printer calibration - a number of guides are available online
|
|
to help with this (for example, do a web search for "3d printer
|
|
calibration").
|