Kevin O'Connor f08a0c5e93 lcd_st7920: Use a longer delay at the start of each command/data ... It appears the st7920 requires a longer delay when switching from command to data mode (and vice-versa). Slower MCUs don't show a problem because the klipper command processing time results in a sufficient delay. However, some of the faster MCUs can process klipper commands fast enough that the next st7920 transfer is sent too fast. Add an additional delay to account for this. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>		2018-06-22 23:47:09 -04:00
..
__init__.py	klippy: Add support for dynamic loading of python modules	2018-01-28 12:19:26 -05:00
ad5206.py	spicmds: Rework SPI message transmission	2018-05-07 09:10:34 -04:00
adc_temperature.py	adc_temperature: Support defining custom sensors in the config file	2018-04-09 15:44:34 -04:00
bed_tilt.py	probe: Rename get_position() callback to get_probed_position()	2018-06-22 15:33:12 -04:00
delta_calibrate.py	probe: Rename get_position() callback to get_probed_position()	2018-06-22 15:33:12 -04:00
display.py	lcd_st7920: Use a longer delay at the start of each command/data	2018-06-22 23:47:09 -04:00
fan.py	fan: Allow the fan shutdown_speed to be configured	2018-05-18 19:12:03 -04:00
gcode_macro.py	gcode_macro: Add the ability to define custom g-code macros	2018-05-25 12:40:06 -04:00
heater_bed.py	heater: Add PrinterHeaters class that stores all sensors and heaters	2018-04-04 23:13:53 -04:00
heater_fan.py	fan: Allow the fan shutdown_speed to be configured	2018-05-18 19:12:03 -04:00
homing_override.py	homing_override: Add axes config parameter	2018-06-11 20:41:18 -04:00
multi_pin.py	pins: Remove module level get_printer_pins() and setup_pin() functions	2018-04-04 12:26:39 -04:00
output_pin.py	output_pin: Fix SET_PIN max_val check	2018-06-05 09:12:31 -04:00
pid_calibrate.py	pid_calibrate: Make sure to unregister new control class on error	2018-04-06 11:39:24 -04:00
probe.py	probe: Rename get_position() callback to get_probed_position()	2018-06-22 15:33:12 -04:00
replicape.py	linux: Convert linux SPI code to use the generic spicmds.c code	2018-05-07 09:10:34 -04:00
servo.py	servo: Use new gcode.register_mux_command()	2018-05-20 12:40:10 -04:00
static_digital_output.py	static_digital_output: Add static_digital_output section to extras/	2018-03-17 13:06:51 -04:00
stepper_buzz.py	stepper: Don't peak into PrinterStepper members	2018-06-22 14:09:01 -04:00
temperature_fan.py	temperature_fan: Fix issue 403 use max_speed	2018-06-19 11:51:07 -04:00
thermistor.py	thermistor: Add Honeywell 100K and MGB18 thermistor definitions	2018-04-30 16:08:17 -04:00
tmc2130.py	tmc2130: Allow the PWMCONF register to be configured	2018-05-25 11:38:27 -04:00
verify_heater.py	verify_heater: Disable when writing output to a debug file	2018-06-08 23:51:41 -04:00
virtual_sdcard.py	gcode: Raise an error if a duplicate command is registered	2018-05-20 13:08:22 -04:00
z_tilt.py	probe: Rename get_position() callback to get_probed_position()	2018-06-22 15:33:12 -04:00