mirror of https://github.com/Desuuuu/klipper.git
142 lines
4.1 KiB
INI
142 lines
4.1 KiB
INI
# This file contains common pin mappings for the Monoprice
|
|
# Select Mini v1. To use this config, the firmware should be compiled for the
|
|
# STM32F103 microcontroller with an 8MHz crystal and USB for communication.
|
|
#
|
|
# Use the following settings in make menuconfig:
|
|
#
|
|
# * Enable extra low-level configuration options: Enable
|
|
# * Microcontroller architecture: STM32
|
|
# * Processor: STM32F103
|
|
# * Bootloader offset: 8KiB bootloader
|
|
# * Clockspeed: 8 Mhz crystal
|
|
# * Communication interface: USB (on PA11/PA12)
|
|
# * GPIO pins to set: PA8, PB1, PB11, PB9
|
|
#
|
|
# IMPORTANT: A bootloader offset of 8KiB will preserver the stock bootloader
|
|
# and allows easy flashing via SDCard without additional hardware.
|
|
#
|
|
# IMPORTANT: Setting PB9 in the the GPIO pins to set at micro-controller
|
|
# startup is required for the USB port to function.
|
|
#
|
|
# PA8, PB1, PB11 in the GPIO pins deactivates the steppers until klippy
|
|
# takes over.
|
|
#
|
|
# Note 1: Prior to flashing klipper, if possible, make a copy of the default
|
|
# or current configuration values for the printer. Running an M503 command
|
|
# will output these values.
|
|
#
|
|
# Note 2: Klipper can be flashed by copying out/klipper.bin to the MPSMv1's
|
|
# SDCard, renaming it to update.bin, and creating an empty file on the SD card
|
|
# named fcupdate.flg. Insert the SDCard while the printer is off it on. After
|
|
# klipper is flashed, remove the SDCard and delete update.bin and fcupdate.flg
|
|
# to prevent the firmware from flashing on every subsequent power-on.
|
|
# Returning to stock firmware without a programmer is possible as long as the
|
|
# bootloader is not overwritten.
|
|
#
|
|
# Note 3: Stepper directions are not consistent in MSPMv1 printers. Check the
|
|
# directions of the printer with M503 in the stock firmware and adjust the
|
|
# dir_pins below accordingly.
|
|
#
|
|
# Note 4: Klipper currently does not support the LCD-UI of this
|
|
# printer, which is connected via serial interface and controlled by an
|
|
# esp8266 using a custom protocol.
|
|
#
|
|
# See ../docs/Config_Reference.md file for a description of all parameters.
|
|
|
|
[stepper_x]
|
|
homing_speed: 15
|
|
step_pin: PB14
|
|
dir_pin: !PB15 # modify stepper direction if necessary
|
|
enable_pin: !PA8
|
|
# rotation_distance varies in the printer model. Check the correct
|
|
# step-rate of the Select Mini in the original firmware (with M503)
|
|
# and calculate the appropriate value for rotation_distance. This has
|
|
# to be done for all axes.
|
|
microsteps: 16
|
|
rotation_distance: 34.510 # 17 teeth on pulley; MXL belt (2.03 pitch)
|
|
endstop_pin: ^!PB4
|
|
position_endstop: 0
|
|
position_max: 120 # default bed width
|
|
position_min: 0
|
|
|
|
[stepper_y]
|
|
homing_speed: 15
|
|
step_pin: PB12
|
|
dir_pin: PB13 # modify stepper direction if necessary
|
|
enable_pin: !PA8
|
|
microsteps: 16
|
|
rotation_distance: 34.510 # check comment in [stepper_x] section
|
|
endstop_pin: ^!PA15
|
|
position_endstop: 0
|
|
position_max: 120 # default bed length
|
|
position_min: 0
|
|
|
|
[stepper_z]
|
|
homing_speed: 10
|
|
step_pin: PB10
|
|
dir_pin: PB2 # modify stepper direction if necessary
|
|
enable_pin: !PB11
|
|
microsteps: 16
|
|
full_steps_per_rotation: 48
|
|
rotation_distance: 0.7 # M4 rod. check comment in [stepper_x] section
|
|
endstop_pin: ^!PB5
|
|
position_endstop: 0.5
|
|
position_max: 120 # default height
|
|
|
|
[extruder]
|
|
# extruder stepper
|
|
step_pin: PB0
|
|
dir_pin: !PC13 # modify stepper direction if necessary
|
|
enable_pin: !PB1
|
|
microsteps: 16
|
|
rotation_distance: 32.990 # 97 steps/mm. check comment in [stepper_x] section
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
# heater
|
|
heater_pin: PB6
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA0
|
|
control: pid
|
|
pid_kp: 20.00
|
|
pid_ki: 0.02
|
|
pid_kd: 250.00
|
|
# temperatures
|
|
min_temp: 0
|
|
max_temp: 250
|
|
max_extrude_only_distance: 425 #for (un-)loading
|
|
|
|
[heater_bed]
|
|
heater_pin: PB7
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA1
|
|
control: pid
|
|
pid_kp: 70.00
|
|
pid_ki: 1.50
|
|
pid_kd: 812.00
|
|
min_temp: 0
|
|
max_temp: 85
|
|
|
|
# Print cooling fan
|
|
[heater_fan hotend_fan]
|
|
pin: PB8
|
|
heater: extruder
|
|
heater_temp: 45.0
|
|
|
|
[mcu]
|
|
serial: /dev/ttyACM0
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 150
|
|
max_accel: 800
|
|
max_z_velocity: 1.5
|
|
max_z_accel: 20
|
|
|
|
# Positions for BED_SCREWS_ADJUST levelling with bed screws still accessible
|
|
[bed_screws]
|
|
screw1: 22, 10
|
|
screw2: 22, 90
|
|
screw3: 98, 90
|
|
screw4: 98, 10
|