mirror of https://github.com/Desuuuu/klipper.git
112 lines
2.1 KiB
INI
112 lines
2.1 KiB
INI
# This file contains common configurations and pin mappings
|
|
# for the Flsun Q5 using the MKS Robin Nano board.
|
|
|
|
# To use this config, the firmware should be compiled for the
|
|
# STM32F103. When running "make menuconfig", enable "extra low-level
|
|
# configuration setup", select the 28KiB bootloader, and serial (on
|
|
# USART3 PB11/PB10) communication.
|
|
|
|
# Note that the "make flash" command does not work with MKS Robin
|
|
# boards. After running "make", run the following command:
|
|
# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano.bin
|
|
# Copy the file out/Robin_nano.bin to an SD card and then restart the
|
|
# printer with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: delta
|
|
max_velocity: 250
|
|
max_accel: 3000
|
|
max_z_velocity: 100
|
|
delta_radius: 107.5
|
|
print_radius: 100
|
|
|
|
[stepper_a]
|
|
step_pin: PE3
|
|
dir_pin: PE2
|
|
enable_pin: !PE4
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: PA15
|
|
homing_speed: 20
|
|
homing_retract_dist: 5
|
|
homing_retract_speed: 10
|
|
second_homing_speed: 2
|
|
position_endstop: 220
|
|
arm_length: 215
|
|
angle: 210
|
|
|
|
[stepper_b]
|
|
step_pin: PE0
|
|
dir_pin: PB9
|
|
enable_pin: !PE1
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: PA12
|
|
angle: 330
|
|
|
|
[stepper_c]
|
|
step_pin: PB5
|
|
dir_pin: PB4
|
|
enable_pin: !PB8
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: PC4
|
|
angle: 90
|
|
|
|
[probe]
|
|
pin: !PA11
|
|
x_offset: 0
|
|
y_offset: 0
|
|
z_offset: 20.26
|
|
speed: 5.0
|
|
samples: 5
|
|
samples_result: average
|
|
sample_retract_dist: 3
|
|
samples_tolerance: 0.02
|
|
samples_tolerance_retries: 5
|
|
|
|
[delta_calibrate]
|
|
radius: 95
|
|
horizontal_move_z: 25
|
|
Speed: 10
|
|
|
|
[extruder]
|
|
step_pin: PD6
|
|
dir_pin: !PD3
|
|
enable_pin: !PB3
|
|
microsteps: 16
|
|
rotation_distance: 22.17
|
|
gear_ratio: 66:22
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PC3
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC1
|
|
control: pid
|
|
pid_kp: 14.529
|
|
pid_ki: 0.557
|
|
pid_kd: 94.802
|
|
min_temp: 0
|
|
max_temp: 250
|
|
max_extrude_only_distance: 110.0
|
|
|
|
[heater_bed]
|
|
heater_pin: PA0
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC0
|
|
control: pid
|
|
pid_Kp: 325.10
|
|
pid_Ki: 63.35
|
|
pid_Kd: 417.10
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PB1
|