mirror of https://github.com/Desuuuu/klipper.git
178 lines
3.0 KiB
INI
178 lines
3.0 KiB
INI
# This file contains common pin mappings for the FlashForge-Creator-Pro
|
|
# To use this config, the firmware should be compiled for
|
|
# the Atmel atmega2560.
|
|
|
|
# Use the following command to flash the board:
|
|
# avrdude -c stk500v2 -p m2560 -P /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_557373136313514061A2-if00 -b 57600 -D -U out/klipper.elf.hex
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PF1
|
|
dir_pin: !PF0
|
|
enable_pin: !PF2
|
|
microsteps: 16
|
|
rotation_distance: 34
|
|
endstop_pin: ^!PL1
|
|
position_endstop: 116
|
|
position_max: 116
|
|
position_min: -116
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PF5
|
|
dir_pin: !PF4
|
|
enable_pin: !PF6
|
|
microsteps: 16
|
|
rotation_distance: 34
|
|
endstop_pin: ^!PL3
|
|
position_endstop: 80
|
|
position_max: 80
|
|
position_min: -80
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PK1
|
|
dir_pin: !PK0
|
|
enable_pin: !PK2
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: !PL6
|
|
position_endstop: -0.25
|
|
position_max: 181
|
|
position_min: -0.25
|
|
|
|
[extruder]
|
|
step_pin: PA3
|
|
dir_pin: !PA2
|
|
enable_pin: !PA4
|
|
microsteps: 16
|
|
rotation_distance: 33
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PH3
|
|
sensor_type: MAX6675
|
|
sensor_pin: PE3
|
|
spi_software_miso_pin: PE5
|
|
spi_software_sclk_pin: PE2
|
|
spi_software_mosi_pin: PA1 #dummy mosi pin
|
|
control: pid
|
|
pid_kp: 27.341
|
|
pid_ki: 1.293
|
|
pid_kd: 144.566
|
|
min_temp: 0
|
|
max_temp: 260
|
|
|
|
[extruder1]
|
|
step_pin: PA7
|
|
dir_pin: PA6
|
|
enable_pin: !PG2
|
|
microsteps: 16
|
|
rotation_distance: 33
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PB5
|
|
sensor_type: MAX6675
|
|
sensor_pin: PE4
|
|
spi_software_miso_pin: PE5
|
|
spi_software_sclk_pin: PE2
|
|
spi_software_mosi_pin: PA1 #dummy mosi pin
|
|
control: pid
|
|
pid_kp: 27.341
|
|
pid_ki: 1.293
|
|
pid_kd: 144.566
|
|
min_temp: 0
|
|
max_temp: 260
|
|
|
|
[gcode_macro T0]
|
|
gcode:
|
|
SET_GCODE_OFFSET X=-34
|
|
ACTIVATE_EXTRUDER EXTRUDER=extruder
|
|
|
|
[gcode_macro T1]
|
|
gcode:
|
|
SET_GCODE_OFFSET X=0
|
|
ACTIVATE_EXTRUDER EXTRUDER=extruder1
|
|
|
|
|
|
[heater_fan extruder_fan]
|
|
pin: PH4
|
|
|
|
[heater_fan extruder1_fan]
|
|
pin: PB6
|
|
|
|
[fan]
|
|
pin: PL5
|
|
|
|
[heater_bed]
|
|
heater_pin: PL4
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PK7
|
|
control: pid
|
|
pid_kp: 72.914
|
|
pid_ki: 2.060
|
|
pid_kd: 645.290
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_557373136313514061A2-if00
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 1000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[mcp4018 x_axis_pot]
|
|
scl_pin: PJ5
|
|
sda_pin: PF3
|
|
wiper: 118
|
|
scale: 127
|
|
|
|
[mcp4018 y_axis_pot]
|
|
scl_pin: PJ5
|
|
sda_pin: PF7
|
|
wiper: 118
|
|
scale: 127
|
|
|
|
[mcp4018 z_axis_pot]
|
|
scl_pin: PJ5
|
|
sda_pin: PK3
|
|
wiper: 40
|
|
scale: 127
|
|
|
|
[mcp4018 a_axis_pot]
|
|
scl_pin: PJ5
|
|
sda_pin: PA5
|
|
wiper: 118
|
|
scale: 127
|
|
|
|
[mcp4018 b_axis_pot]
|
|
scl_pin: PJ5
|
|
sda_pin: PJ6
|
|
wiper: 118
|
|
scale: 127
|
|
|
|
[display]
|
|
lcd_type: hd44780_spi
|
|
spi_software_mosi_pin: PC3
|
|
spi_software_sclk_pin: PC2
|
|
#miso not used, dummy pin.
|
|
spi_software_miso_pin: PJ1
|
|
latch_pin: PC4
|
|
|
|
click_pin: ^PJ0
|
|
back_pin: ^PJ2
|
|
up_pin: ^PJ4
|
|
down_pin: ^PJ3
|
|
|
|
[pca9533 led_strip]
|
|
i2c_bus: twi
|
|
i2c_address: 98
|
|
initial_RED: 1
|
|
initial_GREEN: 1
|
|
initial_BLUE: 1
|