mirror of https://github.com/Desuuuu/klipper.git
144 lines
3.0 KiB
INI
144 lines
3.0 KiB
INI
# This file contains a configuration for the Anycubic Vyper printer from 2021.
|
|
# It uses a clone of the STM32F103 chip named GD32F103.
|
|
# There are 2 Mainboard versions out there v0.0.5 and v0.0.6, this config has
|
|
# been tested with the v0.0.6 only. It should probably work for v0.0.5 as well
|
|
# since there are no different changes in the Anycubic Marlin firmware.
|
|
# The LCD is not supported yet (might work, but didn't try yet).
|
|
#
|
|
# To create the Firmware you need to use the following configuration:
|
|
# - Micro-controller: STM32
|
|
# - Processor model: STM32F103
|
|
# - Bootloader offset: 32KiB
|
|
# - Communication interface: Serial (on USART1 PA10/PA9)
|
|
#
|
|
# To install the Firmware rename the klipper bin to `main_board_20xxxxxx.bin`
|
|
# and copy it to an SD Card.
|
|
# Power off the Printer, insert the SD Card and power it on.
|
|
# It should beep several times and the LCD should be stuck on the Splash screen.
|
|
# Now you should be able to connect to the Printer, you might need to change
|
|
# the mcu/serial setting in this config according to your set up.
|
|
#
|
|
# If you want to revert the Firmware back to Marlin you simply need to flash it
|
|
# with a anycubic firmware through the SD Card
|
|
|
|
[stepper_x]
|
|
step_pin: PC2
|
|
dir_pin: PB9
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: !PA7
|
|
position_min: -3
|
|
position_endstop: -3
|
|
position_max: 245
|
|
homing_speed: 30.0
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: PB7
|
|
enable_pin: !PC13
|
|
microsteps: 16
|
|
rotation_distance: 32
|
|
endstop_pin: !PC5
|
|
position_min: -17
|
|
position_endstop: -17
|
|
position_max: 245
|
|
homing_speed: 30.0
|
|
|
|
[stepper_z]
|
|
step_pin: PB6
|
|
dir_pin: !PB5
|
|
enable_pin: !PC14
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: PB2
|
|
position_endstop: 0.0
|
|
position_max: 260
|
|
position_min: -3
|
|
homing_speed: 5.0
|
|
|
|
[stepper_z1]
|
|
step_pin: PC0
|
|
dir_pin: !PC1
|
|
enable_pin: !PC15
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: PC6
|
|
|
|
[extruder]
|
|
step_pin: PB4
|
|
dir_pin: !PB3
|
|
enable_pin: !PA15
|
|
microsteps: 16
|
|
rotation_distance: 22.6789511 #has to be calibrated by everyone
|
|
gear_ratio: 50:17
|
|
full_steps_per_rotation: 200
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PA1
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PC4
|
|
control: pid
|
|
pid_kp: 28.937
|
|
pid_ki: 1.295
|
|
pid_kd: 161.688
|
|
min_temp: 0
|
|
max_temp: 260
|
|
|
|
[heater_fan extruder_fan]
|
|
pin: PB1
|
|
|
|
[heater_bed]
|
|
heater_pin: PA4
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PB0
|
|
control: pid
|
|
pid_kp: 67.648
|
|
pid_ki: 1.044
|
|
pid_kd: 1095.893
|
|
min_temp: 0
|
|
max_temp: 110
|
|
|
|
[fan]
|
|
pin: PA0
|
|
|
|
[probe]
|
|
pin: !PB12
|
|
z_offset: 0
|
|
activate_gcode:
|
|
probe_reset
|
|
|
|
[output_pin probe_reset_pin]
|
|
pin: PB13
|
|
|
|
[bed_mesh]
|
|
mesh_min: 15,15
|
|
mesh_max: 230, 230
|
|
probe_count: 6,6
|
|
|
|
[filament_switch_sensor runout]
|
|
pause_on_runout: True
|
|
switch_pin: PA5
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
restart_method: command
|
|
|
|
[safe_z_home]
|
|
home_xy_position: -3,-17
|
|
z_hop: 10
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 10
|
|
max_z_accel: 100
|
|
|
|
[gcode_macro probe_reset]
|
|
gcode:
|
|
SET_PIN PIN=probe_reset_pin VALUE=0
|
|
G4 P300
|
|
SET_PIN PIN=probe_reset_pin VALUE=1
|
|
G4 P100
|